Finite Element Analysis of Radial Bearing Magnetic Field

2010 ◽  
Vol 37-38 ◽  
pp. 486-490
Author(s):  
Guo Qing Wu ◽  
Wei Nan Zhu ◽  
Jing Ling Zhou
Keyword(s):  
Magnetic Field ◽  
Finite Element ◽  
Controller Design ◽  
Magnetic Coupling ◽  
System Structure ◽  
Element Analysis ◽  
Radial Bearing ◽  
And Performance ◽  
Magnetic Poles ◽  
The Magnetic Field

There is a magnetic field inside of the radial bearing. The magnetic field distribution is one of the key factors that decides the running state and performance of the system. By using the finite element ANSYS software, the magnetic field of radial bearing was analyzed. The analysis indicated that NSSN mode is suiTable for magnetic radial bearing and NSNS mode unsuiTable. There is a magnetic coupling between magnetic poles. There is magnetic leakage for radial bearing, which leaks towards spindle center through rotor and to coil, but it is very little, less than 5%. The research provides a theoretical basis for optimization of system structure and controller design.

Finite Element Analysis of Thrust Bearing Magnetic Field in 22KW Spindle

2008 ◽  
Vol 392-394 ◽  
pp. 761-766 ◽  
Author(s):  
G.Q. Wu ◽  
J.L. Zhou ◽  
Xu Dong Zhang ◽  
Y.M. Zhang ◽  
Xiao Ni Chi ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Finite Element ◽  
Thrust Bearing ◽  
System Structure ◽  
Magnetic Saturation ◽  
Element Analysis ◽  
Direction Control ◽  
And Performance ◽  
The Magnetic Field ◽  
Flux Leakage

There is a magnetic field inside thrust bearing. The magnetic field distribution is one of the key factors which decide the running state and performance. With the finite element of ANSYS software, the magnetic field of thrust bearing has been analyzed. The rule of changes between the magnetic field and the influencing factors has been discovered. The analysis shows that the direction of exciting current should be opposite other than identical. The greater the ratio of gap length between stator and rotor and working gap length is, the less magnetic field leakage is. The flux leakage of thrust bearing attains 37 percent when the ratio of the gap is 4.0. If the design of a complete machine is not proper, the flux leakage may attain 20 percent upwards through other gaps although that of the bearing itself is almost zero. Calculation of bearing capacity indicates that theoretical value is not exact due to its neglect of magnetic saturation and flux leakage, while FEM value comparably matches the real substance with considering the magnetic saturation and flux leakage. The research provides the theoretical basis for optimization of system structure and selection of current direction control.

scholarly journals Finite Element Analysis of Magnetic Field Exciter for Direct Testing of Magnetocaloric Materials’ Properties

Energies ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2792
Author(s):  
Wieslaw Lyskawinski ◽  
Wojciech Szelag ◽  
Cezary Jedryczka ◽  
Tomasz Tolinski
Keyword(s):  
Magnetic Field ◽  
Finite Element ◽  
Magnetic Circuit ◽  
Homogeneous Magnetic Field ◽  
Element Analysis ◽  
Mcm Testing ◽  
Testing Region ◽  
Magnetocaloric Materials ◽  
Field Excitation ◽  
The Magnetic Field

The paper presents research on magnetic field exciters dedicated to testing magnetocaloric materials (MCMs) as well as used in the design process of magnetic refrigeration systems. An important element of the proposed test stand is the system of magnetic field excitation. It should provide a homogeneous magnetic field with a controllable value of its intensity in the MCM testing region. Several concepts of a magnetic circuit when designing the field exciters have been proposed and evaluated. In the MCM testing region of the proposed exciters, the magnetic field is controlled by changing the structure of the magnetic circuit. A precise 3D field model of electromagnetic phenomena has been developed in the professional finite element method (FEM) package and used to design and analyze the exciters. The obtained results of the calculations of the magnetic field distribution in the working area were compared with the results of the measurements carried out on the exciter prototype. The conclusions resulting from the conducted research are presented and discussed.

Experimental Research on the Magnetic Field Sensitive Polymeric Actuator

2011 ◽  
Vol 287-290 ◽  
pp. 603-607
Author(s):  
Chun Lin Xia ◽  
Yang Fang Wu ◽  
Qian Qian Lu
Keyword(s):  
Magnetic Field ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Energy Conversion ◽  
Experimental Research ◽  
Experimental Results ◽  
Deformation Characteristics ◽  
Analysis Software ◽  
Element Analysis ◽  
The Magnetic Field

Using domestic MFSP membrane as a medium of energy conversion, a kind of MFSP actuator was designed. The dedicated test equipment was constructed for experimental research, and the experimental results were given. The strip and circular MSFP membrane were analyzed qualitatively to obtain the deformation characteristics of membrane by finite element analysis software.

scholarly journals Development of a hybrid vibration converter for real vibration source / Entwicklung eines Hybrid-Vibrationswandlers für eine echte Schwingungsquelle

2019 ◽  
Vol 86 (s1) ◽  
pp. 57-61 ◽  
Author(s):  
Sonia Bradai ◽  
Slim Naifar ◽  
Olfa Kanoun
Keyword(s):  
Magnetic Field ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Energy Harvesting ◽  
Resonant Frequency ◽  
Ambient Vibration ◽  
Vibration Source ◽  
Frequency Bandwidth ◽  
Element Analysis ◽  
The Magnetic Field

AbstractHarvesting energy from ambient vibration sources is challenging due to its low characteristic amplitude and frequencies. In this purpose, this work presents a compact hybrid vibration converter based on electromagnetic and magnetoelectric principles working for a frequency bandwidth and under real vibration source properties. The combination of especially these two principles is mainly due to the fact that both converters can use the same changes of the magnetic field for energy harvesting. The converter was investigated using finite element analysis and validated experimentally. Results have shown that a frequency bandwidth up to 12 Hz with a characteristic resonant frequency at 24 Hz and a power density of 0.11mW/cm3 can be reached.

Finite Element Analysis of the Magnetic Field Simulation of High Temperature Superconducting Magnet

2014 ◽  
Vol 672-674 ◽  
pp. 562-566
Author(s):  
Ying Hong Luo ◽  
Jing Jing Wang
Keyword(s):  
Magnetic Field ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Field Distribution ◽  
Magnetic Energy ◽  
Superconducting Magnet ◽  
Magnetic Field Distribution ◽  
Magnetic Storage ◽  
Element Analysis ◽  
The Magnetic Field

Superconducting Magnetic Energy Storage (SMES) system use conductive coils made of superconductor wire to store energy, its application entirely depends on the design and development of superconducting magnet, as the magnetic storage element, during the operation of the superconducting magnet generates relatively strong magnetic field. In this paper, a 1MJ class single solenoidal SMES with Bi2223/Ag conductor is presented. On the basis of electromagnetic theory, subsequently infers mathematical model of magnetic field distribution by ANSYS finite element analysis software, modeling a two-dimensional electromagnetic analysis of 44 double pancakes to get the magnetic field distribution patterns. The results of the analysis provide a reference for the structural design, optimization of a superconducting magnet and shielding of stray magnetic field.

Finite-Element Analysis of the Magnetic Field in a Magnetic Gear Mechanism

2013 ◽  
Vol 479-480 ◽  
pp. 230-233
Author(s):  
Yi Chang Wu ◽  
Bo Syuan Jian
Keyword(s):  
Magnetic Field ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Permanent Magnets ◽  
Design Parameters ◽  
Element Analysis ◽  
Magnetostatic Field ◽  
Gear Mechanism ◽  
Magnetic Gear ◽  
The Magnetic Field

This paper presents finite-element analysis (FEA) of the magnetic field of a magnetic gear mechanism. An external type magnetic gear mechanism, which consists of two identical magnetic gears with sector-shaped permanent magnets, is introduced first. Then, the magnetostatic field distribution and transmitted torque of the magnetic gear mechanism are simulated by a commercial FEA package Ansoft/ Maxwell. Next, the effects of design parameters, including the air-gap length, the number of magnetic pole pairs, and the height of permanent magnets, on the maximum transmitted torque are discussed. The results of this work are beneficial to the design of magnetic gear mechanisms.

Finite Element Analysis of Magnetization Reversal Effect Based on Ferromagnetic Specimens

2014 ◽  
Vol 620 ◽  
pp. 127-132
Author(s):  
Xiao Wen Xi ◽  
Shang Kun Ren ◽  
Li Hua Yuan
Keyword(s):  
Magnetic Field ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Magnetic Flux ◽  
Magnetization Reversal ◽  
Tensile Load ◽  
Magnetic Flux Leakage ◽  
Element Analysis ◽  
The Magnetic Field ◽  
Flux Leakage

Using large finite element analysis (FEA) software ANSYS, the stress-magnetization effect on 20# steel specimens with different shape notches is simulated under the geomagnetic field and tensile load. With the stimulation, the magnetic flux leakage fields at certain positions of the surface specimen were measured. Through analysis the relationship between the magnetic flux leakage fields of certain points with tensile stress, the results showed that the magnetic field value at certain positions of specimen surface first decreases and then increases along with the increase of stress, which is called magnetization reversal phenomenon; Different gaps and different positions of the specimen show different magnetization reversal rules; By measuring the maximal variation of the magnetic field value △Hmax at certain positions of the surface specimen and by analyzing its change law, we can roughly estimate specimen stress size and distribution regularity of stress. Moreover, this article also discusses the effect of lifts-off of the probe on the law of stress magnetization.

Sign in / Sign up

Export Citation Format

Share Document