Development of Axially Splitting Method for the Pipe Materials with the Cutting Tool

2014 ◽  
Vol 1017 ◽  
pp. 350-354
Author(s):  
Eitoku Nakanishi ◽  
Masayuki Hyono ◽  
Seijiro Maki
Keyword(s):  
Stainless Steel ◽  
Cutting Tool ◽  
Splitting Method ◽  
Axial Direction ◽  
Processing Method ◽  
The Other ◽  
Wall Surface ◽  
Steel Pipes ◽  
Simple Processing ◽  
Pipe Materials

A simple processing method for splitting pipes in the axial direction using a cutting tool was investigated. The special tool developed in this study was pressed into the pipes in the axial direction, and the pipes were split very smoothly without any lubricant. This cutting method did not form fine chips, did not produce a significant heat effect on the inner wall surface. The splitting experiment was carried out with pipes constructed of aluminum and stainless steel. The outer diameters of the pipes were approximately 50 mm, and the thicknesses of the wall varied from 1 to 3 mm. The aluminum pipes were split very smooth by the tool, and curled strip-shaped chips were created by the splitting. On the other hand, the stainless pipes were greatly deformed, making them difficult to cut. Therefore, it was necessary to prevent deformation of the pipe by attaching an outer tool. The outer tool made it possible to cut stainless steel pipes.

Plastic Collapse Stresses for Pipes With Circumferential Twin Flaws Using Combination Rules

2018 ◽  
Author(s):  
Kunio Hasegawa ◽  
Yinsheng Li ◽  
Yun-Jae Kim ◽  
Valery Lacroix ◽  
Bohumir Strnadel
Keyword(s):  
Experimental Data ◽  
Stainless Steel ◽  
Analytical Procedure ◽  
The Other ◽  
Plastic Collapse ◽  
Combination Rules ◽  
Steel Pipes ◽  
Other Hand ◽  
Bending Stresses

When discrete multiple flaws are in the same plane, and they are close to each other, it can be determined whether they are combined or standalone in accordance with combination rules provided by fitness-for-service (FFS) codes, such as ASME, JSME, BS7910, FKM, WES2805, etc. However, specific criteria of the rules are different amongst these FFS codes. On the other hand, plastic collapse bending stresses for stainless steel pipes with circumferential twin flaws were obtained by experiments and the prediction procedure for collapse stresses for pipes with twin flaws were developed analytically. Using the experimental data and the analytical procedure, plastic collapse stresses for pipes with twin flaws are compared with the stresses in compliance with the combination criteria. It is shown that the calculated plastic collapse stresses based on the combination criteria are significantly different from the experimental and analytical stresses.

Plastic Collapse Stresses Based on Flaw Combination Rules for Pipes Containing Two Circumferential Similar Flaws

2019 ◽  
Vol 141 (3) ◽  
Author(s):  
Kunio Hasegawa ◽  
Yinsheng Li ◽  
Yun-Jae Kim ◽  
Valery Lacroix ◽  
Bohumir Strnadel
Keyword(s):  
Experimental Data ◽  
Stainless Steel ◽  
Analytical Procedure ◽  
The Other ◽  
Plastic Collapse ◽  
Combination Rules ◽  
Steel Pipes ◽  
Other Hand ◽  
Bending Stresses

When discrete multiple flaws are in the same plane, and they are close to each other, it can be determined whether they are combined or standalone in accordance with combination rules provided by fitness-for-service (FFS) codes. However, specific criteria of the rules are different among these FFS codes. On the other hand, plastic collapse bending stresses for stainless steel pipes with two circumferential similar flaws were obtained by experiments, and the prediction procedure for collapse stresses for pipes with two similar flaws was developed analytically. Using the experimental data and the analytical procedure, plastic collapse stresses for pipes with two similar flaws are compared with the stresses in compliance with the flaw combination criteria. It is shown that the calculated plastic collapse stresses based on the flaw combination criteria are significantly different from the experimental and analytical stresses.

CLC 18.10LN

Alloy Digest ◽  
2006 ◽  
Vol 55 (1) ◽  
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Shear Strength ◽  
High Temperature ◽  
Austenitic Stainless Steel ◽  
Stainless Steels ◽  
The Other ◽  
Low Carbon ◽  
Good Corrosion Resistance ◽  
Temperature Performance

Abstract CLC 18.10LN is an austenitic stainless steel with 18% Cr, 9.5% Ni, and 0.14% N to provide good corrosion resistance at strengths above the other low-carbon stainless steels. This datasheet provides information on composition, physical properties, elasticity, tensile properties, and shear strength as well as creep. It also includes information on high temperature performance and corrosion resistance as well as forming, machining, and joining. Filing Code: SS-950. Producer or source: Industeel USA, LLC.

Ratcheting assessment of corroded elbow pipes subjected to internal pressure and cyclic bending moment

2021 ◽  
pp. 030932472198989
Author(s):  
Ali Salehi ◽  
Armin Rahmatfam ◽  
Mohammad Zehsaz
Keyword(s):  
Growth Rate ◽  
Stainless Steel ◽  
Internal Pressure ◽  
Bending Moment ◽  
Axial Direction ◽  
Hoop Strain ◽  
Cyclic Bending ◽  
High Fatigue ◽  
The Impact ◽  
Cyclic Bending Moment

The present study aimed to study ratcheting strains of corroded stainless steel 304LN elbow pipes subjected to internal pressure and cyclic bending moment. To this aim, spherical and cubical shapes corrosion are applied at two depths of 1 mm and 2 mm in the critical points of elbow pipe such as symmetry sites at intrados, extrados, and crown positions. Then, a Duplex 2205 stainless steel elbow pipe is considered as an alternative to studying the impact of the pipe materials, due to its high corrosion resistance and strength, toughness, and most importantly, the high fatigue strength and other mechanical properties than stainless steel 304LN. In order to perform numerical analyzes, the hardening coefficients of the materials were calculated. The results highlight a significant relationship between the destructive effects of corrosion and the depth and shape of corrosion, so that as corrosion increases, the resulting destructive effects increases as well, also, the ratcheting strains in cubic corrosions have a higher growth rate than spherical corrosions. In addition, the growth rate of the ratcheting strains in the hoop direction is much higher across the studied sample than the axial direction. The highest growth rate of hoop strain was observed at crown and the highest growth rate of axial strains occurred at intrados position. Altogether, Duplex 2205 material has a better performance than SS 304LN.

Sign in / Sign up

Export Citation Format

Share Document