Asymmetric Incremental Sheet Forming

2005 ◽  
Vol 6-8 ◽  
pp. 35-58 ◽  
Author(s):  
J. Jeswiet
Keyword(s):  
Sheet Metal ◽  
Sheet Metal Forming ◽  
Metal Forming ◽  
Incremental Forming ◽  
Sheet Forming ◽  
Incremental Sheet Forming ◽  
Localized Deformation ◽  
Recent Advances ◽  
Conventional Spinning ◽  
Forming Methods

The use of computers in manufacturing has enabled the development of several new sheet metal forming processes. This paper describes modifications that have been made to traditional forming methods such as conventional spinning and shear forming, where deformation is localized. Recent advances have enabled this localized deformation to be accurately controlled and studied. Current developments have been focused on forming asymmetric parts using CNC technology, without the need for costly dies. Asymmetric Incremental Forming has the potential to revolutionize sheet metal forming, making it accessible to all levels of manufacturing.

A review of conventional and modern single-point sheet metal forming methods

2003 ◽  
Vol 217 (2) ◽  
pp. 213-225 ◽  
Author(s):  
E Hagan ◽  
J Jeswiet
Keyword(s):  
Sheet Metal ◽  
Sheet Metal Forming ◽  
Metal Forming ◽  
Single Point ◽  
Small Region ◽  
Numerical Control ◽  
Localized Deformation ◽  
Flow Forming ◽  
Conventional Spinning ◽  
Forming Methods

The use of computers in manufacturing has enabled the development of several new metal forming processes that are based upon older technologies. In this case modifications have been made to traditional forming methods such as conventional spinning and shear forming. These two processes are similar in that the deformation mechanism is localized to a small region under the forming tool. Recent advances in computing power have enabled this localized deformation to be accurately controlled and studied. Spinning, shear forming and flow forming are limited to forming parts that are symmetrical about the revolving lathe axis. Current research has been focused on forming non-symmetrical parts using computer numerical control (CNC) technology, without the need for costly dies. A comparison of traditional and modern forming methods is presented here in an attempt to illustrate the evolution of different incremental sheet metal forming techniques. Emphasis is placed on conventional spinning, shear forming and modern computer-controlled forming methods that are currently being studied.

scholarly journals Recent Developments and Trends in the Friction Testing for Conventional Sheet Metal Forming and Incremental Sheet Forming

Metals ◽  
2019 ◽  
Vol 10 (1) ◽  
pp. 47 ◽  
Author(s):  
Tomasz Trzepiecinski ◽  
Hirpa G. Lemu
Keyword(s):  
Sheet Metal ◽  
Sheet Metal Forming ◽  
Metal Forming ◽  
Coulomb Friction ◽  
Sheet Forming ◽  
Friction Model ◽  
Friction Resistance ◽  
Friction Testing ◽  
Coulomb Friction Model

Friction is the main phenomenon that has a huge influence on the flow behavior of deformed material in sheet metal forming operations. Sheet metal forming methods are one of the most popular processes of obtaining finished products, especially in aerospace, automobile, and defense industries. Methods of sheet forming are carried out at different temperatures. So, it requires tribological tests that suitably represent the contact phenomena related to the temperature. The knowledge of the friction properties of the sheet is required for the proper design of the conditions of manufacturing processes and tools. This paper summarizes the methods used to describe friction conditions in conventional sheet metal forming and incremental sheet forming that have been developed over a period of time. The following databases have been searched: WebofKowledge, Scopus, Baztool, Bielefield Academic Search Engine, DOAJ Directory of Open Access Journals, eLibrary.ru, FreeFullPdf, GoogleScholar, INGENTA, Polish Scientific Journals Database, ScienceDirect, Springer, WorldCat, WorldWideScience. The English language is selected as the main source of review. However, in a limited scope, databases in Polish and Russian languages are also used. Many methods of friction testing for tribological studies are selected and presented. Some of the methods are observed to have a huge potential in characterizing frictional resistance. The application of these methods and main results have also been provided. Parameters affecting the frictional phenomena and the role of friction have also been explained. The main disadvantages and limitations of the methods of modeling the friction phenomena in specific areas of material to be formed have been discussed. The main findings are as follows—The tribological tests can be classified into direct and indirect measurement tests of the coefficient of friction (COF). In indirect methods of determination, the COF is determined based on measuring other physical quantities. The disadvantage of this type of methods is that they allow the determination of the average COF values, but they do not allow measuring and determining the real friction resistance. In metal forming operations, there exist high local pressures that intensify the effects of adhesion and plowing in the friction resistance. In such conditions, due to the plastic deformation of the material tested, the usage of the formula for the determination of the COF based on the Coulomb friction model is limited. The applicability of the Coulomb friction model to determine the COF is also very limited in the description of contact phenomena in hot SMF due to the high shear of adhesion in total contact resistance.

Investigation of the ultrasonic vibration effect in incremental sheet metal forming process

2015 ◽  
Vol 231 (6) ◽  
pp. 971-982 ◽  
Author(s):  
Mehdi Vahdati ◽  
Ramezanali Mahdavinejad ◽  
Saeid Amini
Keyword(s):  
Sheet Metal ◽  
Ultrasonic Vibration ◽  
Sheet Metal Forming ◽  
Metal Forming ◽  
Longitudinal Vibration ◽  
Numerical Control ◽  
Resonance Phenomenon ◽  
Localized Deformation ◽  
Forming Process ◽  
Incremental Sheet Metal Forming

The mechanism of incremental sheet metal forming is based on plastic and localized deformation of sheet metal. The sheet metal is formed using a hemispherical-head tool in accordance with the path programmed into the computer numerical control milling machine controller. Experimental and numerical analyses have been performed previously on the application of ultrasonic vibration to various metal forming processes. However, thus far, the effects of ultrasonic vibration on incremental sheet metal forming have not been investigated. This article presents the process of design, analysis, manufacture and testing of a vibrating forming tool for the development of ultrasonic vibration–assisted incremental sheet metal forming. The results obtained from modal analysis and natural frequency measurement of the vibrating tool confirmed the emergence of a longitudinal vibration mode and resonance phenomenon in the forming tool. Then, the effect of ultrasonic vibration on incremental sheet metal forming was studied. The obtained experimental results from the straight groove test on Al 1050-O sheet metals showed that ultrasonic vibration led to decrease in the following parameters as compared with conventional incremental sheet metal forming: applied force on forming tool axis, spring-back and surface roughness of formed sample.

Incremental Forming of Sandwich Panels

2007 ◽  
Vol 344 ◽  
pp. 591-598 ◽  
Author(s):  
K.P. Jackson ◽  
J.M. Allwood ◽  
M. Landert
Keyword(s):  
Mild Steel ◽  
Sheet Metal ◽  
Sandwich Panel ◽  
Incremental Forming ◽  
Sandwich Panels ◽  
Economic Benefits ◽  
Sheet Forming ◽  
Incremental Sheet Forming ◽  
Sheet Metals

This paper presents a first investigation of the applicability of incremental sheet forming (ISF) to sandwich panels. Two initial tests on various sandwich panel designs established that sandwich panels which are ductile and incompressible are the most suitable for the process. Further tests on a sandwich panel with mild steel face plates and a continuous polypropylene core demonstrated that patterns of deformation and tool forces followed similar trends to a sheet metal. It is concluded that, where mechanically feasible, ISF can be applied to sandwich panels using existing knowledge of sheet metals with the expectation of achieving similar economic benefits. Potentially this will increase the range of applications for which sandwich panels are viable.

Experimental Study on Residual Formability of Single Point Incrementally Formed Part

2019 ◽  
Author(s):  
Chetan P. Nikhare
Keyword(s):  
Sheet Metal ◽  
Sheet Metal Forming ◽  
Metal Forming ◽  
Incremental Forming ◽  
Thickness Distribution ◽  
Single Point ◽  
Forming Limit ◽  
Single Point Incremental Forming ◽  
Forming Process ◽  
Conventional Process

Abstract A substantial increase in demand on the sheet metal part usage in aerospace and automotive industries is due to the increase in the sale of these products to ease the transportation. However, due to the increase in fuel prices and further environmental regulation had left no choice but to manufacture more fuel efficient and inexpensive vehicles. These heavy demands force researchers to think outside the box. Many innovative research projects came to replace the conventional sheet metal forming of which single point incremental forming is one of them. SPIF is the emerging die-less sheet metal forming process in which the single point tool incrementally forces any single point of sheet metal at any processing time to undergo plastic deformation. It has several advantages over the conventional process like high process flexibility, elimination of die, complex shape and better formability. Previous literature provides enormous research on formability of metal during this process, process with various metals and hybrid metals, the influence of various process parameter, but residual formability after this process is untouched. Thus, the aim of this paper is to investigate the residual formability of the formed parts using single point incremental forming and then restrike with a conventional tool. The common process parameters of single point incremental forming were varied, and residual formability was studied through the conventional process. The strain and thickness distribution were measured and analyzed. In addition, the forming limit of the part was plotted and compared.

Review of the effect of process parameters on performance measures in the incremental sheet forming process

2020 ◽  
pp. 095440542096121
Author(s):  
Ashish Gohil ◽  
Bharat Modi
Keyword(s):  
Process Parameters ◽  
Metal Forming ◽  
Lead Time ◽  
Incremental Forming ◽  
Low Cost ◽  
Research Work ◽  
Sheet Forming ◽  
Commercial Production ◽  
Incremental Sheet Forming ◽  
Forming Process

Incremental sheet forming process has developed the interest of researchers in the field of sheet metal forming due to high formability and capability to produce prototypes of new products at low cost and minimum lead time. Research work is going on in various front to enhance the process capabilities so that it can be explored for commercial production. In this article, progress and recent development in the field of incremental forming has been reviewed and presented for the benefit of practicing engineers and industry. The effect of various process parameters on the performance of the process have been summarized in this paper. Moreover, the issues which need attention are discussed towards the conclusion of this paper.

Forces in Single Point and Two Point Incremental Forming

2005 ◽  
Vol 6-8 ◽  
pp. 449-456 ◽  
Author(s):  
J. Jeswiet ◽  
Joost R. Duflou ◽  
Alexander Szekeres
Keyword(s):  
Sheet Metal ◽  
Incremental Forming ◽  
Single Point ◽  
Sheet Forming ◽  
Incremental Sheet Forming ◽  
Single Point Incremental Forming

Forces have been measured in Two Point Incremental Forming and Single Point Incremental Forming of Sheet Metal. It is necessary to know the magnitude of these forces when trying to determine if the equipment available is capable of Forming Sheet Metal by either one of the two foregoing processes. The magnitude of forces is also needed when developing appropriate models for the Incremental Sheet Forming. The forces measured in forming cones and truncated pyramids from AA 3003-0 are described.

Sign in / Sign up

Export Citation Format

Share Document