ST14 Material Stamping Process Applications of Finite Element Analysis

2013 ◽  
Vol 711 ◽  
pp. 214-218
Author(s):  
Xiao Jiang Yuan ◽  
Qiu Ju Zhang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Material Structure ◽  
Analysis Software ◽  
Forming Process ◽  
Element Analysis ◽  
Stamping Process ◽  
Back Door ◽  
Material Forming ◽  
Process Structure

ST14 material around the back door window frames of the front bracket parts for the carrier, and to AutoForm stamping process finite element analysis software as a platform for ST14 experience of the material structure process simulation of material forming process, the analysis of the parts stamping process defects through repeated amendments of Part Process structure, to achieve the purpose of stamping process defects.

Numerical Simulation of Liner Curvature Radius on Formation of LEFP

2014 ◽  
Vol 941-944 ◽  
pp. 2305-2308 ◽  
Author(s):  
Rui Jun Gou
Keyword(s):  
Numerical Simulation ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Small Radius ◽  
Curvature Radius ◽  
Arbitrary Lagrangian Eulerian ◽  
Analysis Software ◽  
Forming Process ◽  
Element Analysis ◽  
Charge Structure

In order to obtain a linear explosively formed projectile (LEFP) with a good flying form under large stand-off, the LS-Dyna finite element analysis software and arbitrary Lagrangian - Eulerian (ALE) algorithm were used to simulate the forming process of LEFP with a 30mm charge structure diameter. On the basis of that, the only changed factor was the curvature radius of the liner which was selected as 0.65D, 0.75D, 0.85D, 1.0D and 1.1D for the simulation of LEFP forming progress. The warhead speed-time curves and fracture surfaces of the LEFP are analyzed, with liner radius decreasing, the projectiles become more slender, and instead, the larger radius liner forms flat and wide LEFP. Slender LEFP is conductive to penetration, however the over small radius which cause the reduction of weight and kinetic energy makes fracture easily, oversize radius influence either end of LEFP that warps upward seriously , what means speed grads of both ends differ greatly .The suitable radius ranges from 0.75D to 1.0D.

Finite Element Analysis and Optimization of the Truss of Installing Wave-Maker Based on ANSYS

2013 ◽  
Vol 313-314 ◽  
pp. 1038-1041
Author(s):  
Shou Jun Wang ◽  
Xing Xiong ◽  
Chao Li
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Design Parameters ◽  
Analysis Software ◽  
Element Analysis ◽  
Large Span ◽  
The Finite Element Analysis ◽  
Wave Maker

According to uncertainty of the design parameters for large span truss of installing wave-maker, in order to avoid the waste of materials,the truss is analyzed based on the finite element analysis software ANSYS to find out its weaknesses and various parts of the deformation. On the premise of ensuring the intensity and stiffness, the weight of the truss is reduced by adjusting its sizes and selecting different profiles, so as to achieve the optimization of the truss of installing wave-maker.

Experimental Research on the Magnetic Field Sensitive Polymeric Actuator

2011 ◽  
Vol 287-290 ◽  
pp. 603-607
Author(s):  
Chun Lin Xia ◽  
Yang Fang Wu ◽  
Qian Qian Lu
Keyword(s):  
Magnetic Field ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Energy Conversion ◽  
Experimental Research ◽  
Experimental Results ◽  
Deformation Characteristics ◽  
Analysis Software ◽  
Element Analysis ◽  
The Magnetic Field

Using domestic MFSP membrane as a medium of energy conversion, a kind of MFSP actuator was designed. The dedicated test equipment was constructed for experimental research, and the experimental results were given. The strip and circular MSFP membrane were analyzed qualitatively to obtain the deformation characteristics of membrane by finite element analysis software.

Sign in / Sign up

Export Citation Format

Share Document