Transversely Isotropic Hyperelastic Constitutive Models for Plastic Thermoforming Simulation

2013 ◽  
Vol 554-557 ◽  
pp. 1715-1728 ◽  
Author(s):  
Zied Oueslati ◽  
Mohamed Rachik ◽  
Marie France Lacrampe
Keyword(s):  
Constitutive Modeling ◽  
Strain Energy ◽  
Soft Tissues ◽  
Measurement Data ◽  
Constitutive Models ◽  
Transversely Isotropic ◽  
Tensile Tests ◽  
Energy Potential ◽  
Transversally Isotropic ◽  
Made In

For several years, modeling hyperelasticity has been focused on and leaded to a large choice of strain energy potential forms. Since then, many advances have been made in constitutive modeling of rubber like materials. These models are nowadays widely used in many applications like constitutive modeling of soft tissues in biomechanics problems or plastic thermoforming simulation. In this work, constitutive modeling of TPO sheets for thermoforming application is considered. Experimental measurements have shown that the material is transversely isotropic. To take into account this anisotropy, we implemented some new transversally isotropic hyperelastic constitutive models in Abaqus software with the help of user subroutines. Furthermore, different particular forms of the strain energy potential are investigated and their hyperelatic constants are fitted to the measurement data from tensile tests performed in different directions. Based on the results of these investigations, a transversely isotropic form of the energy potential derived from the Yeoh constitutive model is adopted and several tests are analyzed for validation purpose. The chosen model is a good compromise that achieves accurate predictions with limited amount of tests and limited identification efforts. Another key finding of this work is the influence of the anisotropy on the thermoformed parts.

scholarly journals Comparison of Constitutive Models for predicting the formability of SS 304 by tubular hydroforming process

2022 ◽  
Vol 12 (1) ◽  
pp. 0-0
Keyword(s):  
Constitutive Modeling ◽  
Constitutive Models ◽  
Tensile Tests ◽  
Forming Limit ◽  
Uniaxial Tensile ◽  
Hardening Models ◽  
Forming Precision ◽  
Hydroforming Process ◽  
Ss 304 ◽  
Forming Limit Curves

Finite Element (FE) simulation of sheet/tube forming precision depends mainly on the accuracy of the constitutive modeling. The present paper aim is to compare the constitutive models to fit the stress-strain curves. The accurate deformation behavior of the SS 304 tubes depends on the constitutive modeling of hardening behavior. Deformation data of the tensile specimens cut from tubular sample were collected by conducting Uniaxial tensile tests (UTT) at three different rolling directions. Five constitutive relationships were then recognized by fitting the true stress and strain data with the constitutive models of Hollomon, Power, Krupowsky, Voce and Ghosh, and the fitting accuracy were analyzed and compared. Effects of hardening models on Forming Limit Curves (FLC), pressure loading and bulge height of the hydroformed tube were then studied. The obtained FLC from the simulations were compared with experimental FLC to predict the accuracy of the hardening models.

scholarly journals Constitutive Models for the Tensile Behaviour of TRM Materials: Literature Review and Experimental Verification

Materials ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 700
Author(s):  
Maria Concetta Oddo ◽  
Giovanni Minafò ◽  
Lidia La Mendola
Keyword(s):  
State Of The Art ◽  
Constitutive Models ◽  
Stress Transfer ◽  
Theoretical Models ◽  
Tensile Tests ◽  
Analytical Models ◽  
Tensile Behaviour ◽  
Tensile Response ◽  
Textile Reinforced Mortar ◽  
Inorganic Matrix

In recent years, the scientific community has focused its interest on innovative inorganic matrix composite materials, namely TRM (Textile Reinforced Mortar). This class of materials satisfies the need of retrofitting existing masonry buildings, by keeping the compatibility with the substrate. Different recent studies were addressed to improve the knowledge on their mechanical behaviour and some theoretical models were proposed for predicting the tensile response of TRM strips. However, this task is complex due to the heterogeneity of the constituent materials and the stress transfer mechanism developed between matrix and fabric through the interface in the cracked stage. This paper presents a state-of-the-art review on the existing constitutive models for the tensile behavior of TRM composites. Literature experimental results of tensile tests on TRM coupons are presented and compared with the most relevant analytical models proposed until now. Finally, a new experimental study is presented and its results are used to further verify the reliability of the literature expressions.

A NUMERICAL STUDY ON A TRANSVERSELY ISOTROPIC PERMEABILITY MODEL APPLIED TO SOFT TISSUES

2021 ◽  
Author(s):  
Thayller Weverton Barp ◽  
Bruno Klahr ◽  
Thiago André Carniel ◽  
Eduardo Fancello
Keyword(s):  
Soft Tissues ◽  
Numerical Study ◽  
Transversely Isotropic ◽  
Permeability Model

scholarly journals Applying ASTM Standards to Tensile Tests of Musculoskeletal Soft Tissue: Methods to Reduce Grip Failures and Promote Reproducibility

2020 ◽  
Vol 143 (1) ◽  
Author(s):  
Madison E. Wale ◽  
Derek Q. Nesbitt ◽  
Bradley S. Henderson ◽  
Clare K. Fitzpatrick ◽  
Jaremy J. Creechley ◽  
...  
Keyword(s):  
Tensile Testing ◽  
Soft Tissues ◽  
Tensile Tests ◽  
Standard Test ◽  
International Standards ◽  
Fiber Reinforced Composites ◽  
Fiber Direction ◽  
Reinforced Composites ◽  
Fiber Reinforced ◽  
Test Standards

Abstract Tensile testing is an essential experiment to assess the mechanical integrity of musculoskeletal soft tissues, yet standard test methods have not been developed to ensure the quality and reproducibility of these experiments. The ASTM International standards organization has created tensile test standards for common industry materials that specify geometric dimensions of test specimens (coupons) that promote valid failures within the gage section (midsubstance), away from the grips. This study examined whether ASTM test standards for plastics, elastomers, and fiber-reinforced composites are suitable for tensile testing of bovine meniscus along the circumferential fiber direction. We found that dumbbell (DB) shaped coupons based on ASTM standards for elastomers and plastics had an 80% and 60% rate of midsubstance failures, respectively. The rate of midsubstance failures dropped to 20% when using straight (ST) coupons based on ASTM standards for fiber-reinforced composites. The mechanical properties of dumbbell shaped coupons were also significantly greater than straight coupons. Finite element models of the test coupons revealed stress distributions that supported our experimental findings. In addition, we found that a commercial deli-slicer was able to slice meniscus to uniform layer thicknesses that were within ASTM dimensional tolerances. This study provides methods, recommendations, and insights that can advance the standardization of tensile testing in meniscus and other soft fibrous tissues.

Experimental and Numerical Investigations on Hot Deformation Behavior and Processing Maps for ASS 304 and ASS 316

2018 ◽  
Vol 37 (9-10) ◽  
pp. 873-888 ◽  
Author(s):  
Nitin Kotkunde ◽  
Hansoge Nitin Krishnamurthy ◽  
Swadesh Kumar Singh ◽  
Gangadhar Jella
Keyword(s):  
Experimental Data ◽  
Strain Rate ◽  
Hot Deformation ◽  
Deformation Behavior ◽  
Constitutive Models ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
Processing Maps ◽  
Hot Deformation Behavior ◽  
Statistical Measures

AbstractA thorough understanding of hot deformation behavior plays a vital role in determining process parameters of hot working processes. Firstly, uniaxial tensile tests have been performed in the temperature ranges of 150 °C–600 °C and strain rate ranges of 0.0001–0.01s−1 for analyzing the deformation behavior of ASS 304 and ASS 316. The phenomenological-based constitutive models namely modified Fields–Backofen (m-FB) and Khan–Huang–Liang (KHL) have been developed. The prediction capability of these models has been verified with experimental data using various statistical measures. Analysis of statistical measures revealed KHL model has good agreement with experimental flow stress data. Through the flow stresses behavior, the processing maps are established and analyzed according to the dynamic materials model (DMM). In the processing map, the variation of the efficiency of the power dissipation is plotted as a function of temperature and strain rate. The processing maps results have been validated with experimental data.

scholarly journals Modelling Inhomogeneity of Veneer Laminates with a Finite Element Mapping Method Based on Arbitrary Grayscale Images

Materials ◽  
2020 ◽  
Vol 13 (13) ◽  
pp. 2993
Author(s):  
David Zerbst ◽  
Christian Liebold ◽  
Thomas Gereke ◽  
André Haufe ◽  
Sebastian Clauß ◽  
...  
Keyword(s):  
Finite Element ◽  
Point Cloud ◽  
Nearest Neighbor ◽  
Measurement Data ◽  
Tensile Tests ◽  
Mapping Method ◽  
Nearest Neighbor Search ◽  
Failure Behavior ◽  
Element Mesh ◽  
Mapping Tool

Failure and deformation behavior of veneer laminates of ring porous wood species vary with the individual arrangement of early- and latewood zones over a veneer sheet. Therefore, a method is presented, where local failure and damage modes are considered for finite element models with respect to forming simulations, during the development process of automotive interior trim parts. Within the mapping tool Envyo, a routine has been realized for the discretization of early- and latewood zones from ash wood veneer surfaces to finite element meshes. The routine performs the following steps: reading a grayscale image of known size and generation of a point cloud based on the number of pixels; transformation and scaling of the generated point cloud to align with a target finite element mesh; nearest neighbor search and transfer of grayscale values to the target mesh element centroids; assigning part and therefore material properties to the target elements based on the mapped grayscale value and user-defined grayscale ranges. Due to the absence of measurement data for early- and latewood, optimization was used to identify locally varying material constants. A set of material input parameters for early- and latewood was created, calibrating the force-displacement response of tensile test simulations to corresponding experimental curves. The numerical results gave a very good agreement to the failure behavior of tensile tests in the loading directions longitudinal and transverse to the fiber orientation. Furthermore, in a stochastic analysis the characteristic distribution of tensile strength and ultimate strain could be verified for the suggested procedure. The introduced modelling approach can be applied for the discrete implementation of inhomogeneity to numerical simulations.

Sign in / Sign up

Export Citation Format

Share Document