Roll Casting of Al-Mg-Si Alloy

2021 ◽  
Vol 880 ◽  
pp. 3-8
Author(s):  
Toshio Haga ◽  
Keisuke Oida ◽  
Hisaki Watari ◽  
Shinichi Nishida
Keyword(s):  
Aluminum Alloy ◽  
High Speed ◽  
Die Casting ◽  
Sheet Forming ◽  
Drawing Ratio ◽  
Cast Aluminum ◽  
Roll Casting ◽  
Chemical Content ◽  
Cold Rolled ◽  
Twin Roll

The aluminum alloy Al–5%Mg–2%Si, the chemical content of which is close to that of the Magsimal-59 aluminum alloy commonly for die casting, was successfully cast into strips using a vertical high-speed twin-roll caster at a speed of 30 m/min. This means that Al–5%Mg–2%Si is suitable for the high-speed twin roll-casting. The as-cast Al–5%Mg–2%Si strip was then successfully cold-rolled to a thickness of 0.7 mm. Tension and cup tests were conducted on the cold-rolled annealed strips. The tensile stress was 205 MPa and the elongation was 20% for a thickness of 1 mm. The limiting drawing ratio was 2.0 at a 0.7 mm thickness. The present results demonstrates that Al–5%Mg–2%Si can be used for die casting and sheet forming. This means that use of this alloy for both sheet forming and die casting could eliminate the need for the separation of wrought aluminum alloys from cast aluminum prior to processing at recycling plants.

Roll Casting and Die Casting of Si-Added Al-Mg Alloy

2020 ◽  
Vol 1007 ◽  
pp. 12-17
Author(s):  
Toshio Haga ◽  
Shinichiro Imamura ◽  
Hiroshi Fuse ◽  
Hisaki Watari ◽  
Shinichi Nishida
Keyword(s):  
High Speed ◽  
Die Casting ◽  
Sheet Forming ◽  
Mg Alloy ◽  
Tension Tests ◽  
Roll Casting ◽  
Cold Rolled ◽  
Twin Roll Caster ◽  
Si Content ◽  
Twin Roll

Si ranging from 0.2 mass% to 2.0 mass% was added to Al-5%Mg alloy (5182) and strip was cast by a vertical type high-speed twin-roll caster at a speed of 80 m/min. The as-cast strip was cold-rolled down to 1 mm thickness and annealed. The mechanical properties were investigated using cup tests and tension tests. The limiting draw ratio (LDR) of the 5182 alloy was 2.0 and the LDR became smaller as the Si content increased. When the Si content was 2.0 mass%, the LDR was 1.8, which shows that Si-added 5182 can be used for sheet forming, if the Si content is less than 2.0 mass%. The tensile strength and elongation were almost constant when the Si content was less than 1 mass%, but decreased at 2.0 mass% Si. However, the elongation was greater than 20% at 2.0 mass% Si. For die casting, 2.0 mass% Si was determined as the appropriate content from the results of the tension tests. When the Si content is in the range from 1.0 mass% to 2.0 mass%, then the Si added Al-5%Mg has the ability to be used for both die casting and sheet forming.

Application of Vertical-Type High-Speed Twin-Roll Casting for Up-Grade Recycling and Clad Sheets Fabrication of Aluminum Alloys

2016 ◽  
Vol 877 ◽  
pp. 56-61 ◽  
Author(s):  
Shinji Kumai ◽  
Yusuke Takayama ◽  
Ryoji Nakamura ◽  
Daisuke Shimosaka ◽  
Yohei Harada ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
High Speed ◽  
Cast Aluminum Alloy ◽  
Cast Aluminum ◽  
Casting Method ◽  
Twin Roll Casting ◽  
Roll Casting ◽  
Twin Roll Cast ◽  
Twin Roll

A horizontal-type twin roll casting method has been popular for producing aluminum alloy strips, however, it is characterized by a relatively low productivity (1~6 m/min). In contrast, a vertical-type high-speed twin-roll casting method possesses an extremely high productivity (60~120 m/min (1~2 m/s)) and an excellent heat extraction ability. The rapid cooling effect provided significant microstructure refinement and mechanical properties improvement in various kinds of cast aluminum alloy products. Not only “product to product recycling” but also “up-grade recycling” can be achieved by making good use of these merits. Two examples of application showing the potential of vertical-type high-speed twin roll casting method are presented. (1) Several kinds of Al-Si base alloy were cast into the strips. Not only strength and toughness but also formability was increased in the twin roll cast products. In particular, great improvement in deformability shows the potential of the twin-roll cast aluminum alloy products as substitutes for some wrought aluminum alloy products. (2) The vertical-type tandem twin-roll caster was able to fabricate a clad strip by single step. The A4045/A3003/A4045 aluminum alloy clad sheets produced by the twin-roll casting showed better mechanical properties than the conventional hot-roll bonded clad sheets.

Roll Casting of Recycled AA5182

2011 ◽  
Vol 121-126 ◽  
pp. 4667-4670
Author(s):  
Toshio Haga ◽  
Kosuke Komeda ◽  
Kenta Mtsuoka ◽  
Shinji Kumai ◽  
Hisaki Watari
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
High Speed ◽  
Model Alloy ◽  
Drawing Ratio ◽  
Roll Speed ◽  
Roll Casting ◽  
Twin Roll Caster ◽  
Twin Roll ◽  
Fe Addition

Roll casting of the model alloy of recycled AA5182 aluminum alloy was investigated. Fe up to 0.6% was added to the AA5182 to make the model alloys of recycled AA5182. Increase of 0.6% of Fe means that the recycle was three times operated. A vertical type high speed twin roll caster was used. Some devices were operated on the twin roll caster to increase the cooling rate in order to make impurity fine. The roll speed could be increased up to 80m/min. The roll-castability did not become worse by the addition of the Fe. The LDR (limiting Drawing Ratio) was 1.9 when the Fe addition was 0.6. The deterioration of the mechanical properties by the addition of impurity Fe was very small.

Inline Rolling of 5182 Aluminum Alloy Strip Cast by a Vertical Type High Speed Twin Roll Caster

2010 ◽  
Vol 139-141 ◽  
pp. 477-480
Author(s):  
Ryoji Nakamura ◽  
Shuya Hanada ◽  
Shinji Kumai ◽  
Hisaki Watari
Keyword(s):  
Aluminum Alloy ◽  
High Speed ◽  
Rolling Speed ◽  
Center Line ◽  
Alloy Strip ◽  
Ripple Mark ◽  
Roll Casting ◽  
Strip Cast ◽  
Twin Roll Caster ◽  
Twin Roll

An inline hot rolling was operated on 5182 aluminum alloy strip cast using a vertical type high speed caster (VHSTRC) at the speed of 60 m/min. A porosity existing at center line of the thickness and a ripple mark on the surface, these are typical defects of the strip cast by the VHSTRC, could be improved by the inline rolling. The rolling speed was as same as the roll-casting-speed of 60m/min. The temperature of the strip, when the inline rolling was operated, was 450oC. The reduction of the strip of the inline rolling was 35%.

Globular Crystals in the Center of Roll Cast Aluminum Alloy Strips

2020 ◽  
Vol 1007 ◽  
pp. 34-40
Author(s):  
Toshio Haga ◽  
Maho Tsuchida ◽  
Hirotaka Sakata ◽  
Hisaki Watari ◽  
Shinichi Nishida
Keyword(s):  
Aluminum Alloy ◽  
High Speed ◽  
Strip Casting ◽  
Cast Aluminum Alloy ◽  
Thickness Direction ◽  
Cast Aluminum ◽  
Cooling Slope ◽  
Roll Gap ◽  
Twin Roll ◽  
Center Area

This study investigated the crystallization position and formation mechanism of globular crystals at the center area in the thickness direction of aluminum alloy strips cast by a high-speed twin roll caster. Twin roll casters for single strips and clad strips were used, as well as twin roll casters equipped with a cooling slope. The globular crystals were formed from dividing arms of dendrites of the solidified layer facing the center area at the roll gap. The arms of isolated dendrite also divided. No globular crystals were formed at the interfaces of clad strips with different solidification temperatures because of the temperature gradient at the interface which inhibited division of the dendrite arms. It was demonstrated that globular crystals at the center area of the thickness direction were formed by dendrite-arm-dividing at the roll gap by the strip casting clad strip. Experiments by semisolid-strip casting with the cooling slope showed that globular crystals in the molten metal existed in the solidification layers.

High Speed Twin-Roll Casting of Al-Mg Alloys

2010 ◽  
Vol 154-155 ◽  
pp. 1544-1548 ◽  
Author(s):  
Kosuke Komeda ◽  
Ryoji Nakamura ◽  
Shinji Kumai
Keyword(s):  
Heat Transfer ◽  
Aluminum Alloy ◽  
High Speed ◽  
Aluminum Alloy 5182 ◽  
Roll Casting ◽  
Twin Roll Caster ◽  
Deep Drawing Test ◽  
Study Heat Transfer ◽  
Twin Roll ◽  
Steel Rolls

The disadvantages of the conventional twin-roll caster for aluminum alloy are low casting speeds and limited choices of alloys that are castable by this processing. It is known that strip casting of aluminum alloy 5182 is very difficult because of their wider freezing zones. The vertical-type high-speed twin-roll caster used in the present study was devised to overcome these disadvantages. Features of the high speed twin roll casters are as below. Mild steel rolls were used in order to increase the casting speed and to be made at a lower equipment cost. Roll coating is produced in casting of Al-Mg alloy. Therefore lubricant, that resists heat transfer, was not used in the present study. Heat transfer between melt and the roll was improved by hydrostatic pressure of the melt. Low superheat casting was carried out in order to improve microstructure of the strip. In the present study, effectiveness of a high-speed twin roll caster for recycling aluminum alloy was investigated. The effects of the high-speed twin roll caster on alleviating the deterioration of mechanical properties by impurities were investigated. Properties of the cast strip were investigated by metalography, a tension test, and a deep drawing test.

Roll Casting of Al-SiCp Strip

2011 ◽  
Vol 675-677 ◽  
pp. 811-814 ◽  
Author(s):  
Toshio Haga ◽  
Teppei Nakamura ◽  
S. Kumai ◽  
H. Watari
Keyword(s):  
Hot Rolling ◽  
High Speed ◽  
Strip Casting ◽  
Cast Strip ◽  
Fine Grain ◽  
Roll Casting ◽  
Speed Up ◽  
Cold Rolled ◽  
Twin Roll Caster ◽  
Twin Roll

The strip casting of Al-SiCp alloy was operated by a high speed twin roll caster. The content of SiCp was 20Vol% and 30Vol%. Both of Al-20Vol%SiCp and Al-30Vol%SiCp strips could be cast continuously at the speed up to 90m/min. The SiCp particle distributed uniformly. This was the effect of fine grain of the strip. The as-cast strip of Al-20Vol%SiCp could be cold rolled after homogenization. The as-cast strip of Al-30Vol%SiCp could be cold rolled after once hot rolling and annealing. The as-cast strip of Al-20Vol%SiCp could be coiled at the diameter of 460mm.

Roll Casting of Aluminum Alloy Strip by a Single Roll Caster Equipped with a Scraper

2012 ◽  
Vol 445 ◽  
pp. 307-312 ◽  
Author(s):  
Toshio Haga ◽  
Kazuya Akitsu ◽  
Shinji Kumai ◽  
Hisaki Watari
Keyword(s):  
Aluminum Alloy ◽  
Contact Surface ◽  
Rolled Strip ◽  
Drawing Ratio ◽  
Cast Strip ◽  
Roll Casting ◽  
Single Side ◽  
Twin Roll Caster ◽  
Deep Drawing Test ◽  
Twin Roll

A single roll caster equipped with a scraper was devised to cast the strip with sound free solidified surface. A property of this single caster is equipment of the scraper. Semisolid metal on the free solidified surface was scribed by a scraper and the surface became flat. Center line segregation did not occur as the strip was solidified from single side. The AA5182 aluminum alloy could be cast at speeds up to 40m/min. Thickness was about 3mm. Pressure of the unit width from the scraper was ranging from 0.1N/mm to 1.0N/mm, and these pressure was enough to make the free solidified surface flat. Roll cast strip could be cold rolled down to 1mm. There was not difference between roll contact surface and the free solidified surface after cold rolling by a visual examination. Result of tension test of the roll cast strip was as same as that of D.C. cast and rolled strip. Deep drawing test was operated at the conditions both of the roll contact surface and the free solidified surface was outside. LDR (limited drawing ratio) was same at both conditions and they were 1.8. Thickness of the strip was controlled by the roll speed, solidification length (length of the melt pool) and pressure of the scraper. The single roll caster is simpler than a twin roll caster. Rigidity for rolling was not needed for the single roll caster. Cost of the roll is half comparing a twin roll caster. The equipment cost of the single roll caster is more economy than that of the twin roll caster.

scholarly journals Texture analysis of cold rolled and annealed aluminum alloy produced by twin-roll casting

2011 ◽  
Vol 15 (1) ◽  
pp. 97-102 ◽  
Author(s):  
Juliana de Paula Martins ◽  
André Luis Moreira de Carvalho ◽  
Angelo Fernando Padilha
Keyword(s):  
Aluminum Alloy ◽  
Texture Analysis ◽  
Twin Roll Casting ◽  
Roll Casting ◽  
Cold Rolled ◽  
Twin Roll
Sign in / Sign up

Export Citation Format

Share Document