Effectiveness Evaluation Criteria of Using Fine Powders of Secondary Concrete as a Component of Composite Binder

2021 ◽  
Vol 1017 ◽  
pp. 163-171
Author(s):  
Tatiana Drozdyuk ◽  
Arkady Ayzenshtadt ◽  
Sergey Aksenov

The paper considers the possibility of using energy criteria (surface activity, free surface energy) to quantify the efficiency of a highly dispersed system consisting of fine particles of secondary concrete as a component of composite binder of the hydration type of hardening. Using the G.A. Zisman method, the value of the critical surface tension was determined for secondary concrete fractions with different degrees of dispersion, which gives an idea of the free surface energy of a surface area unit. Based on the experimental data for determining the specific surface area and critical surface tension, the free surface energy and surface activity of the studied concrete powder were calculated, which can serve as criteria for quantitative energy characteristics of raw materials for the production of composite binders. Calorimetric studies related to measurements of the thermal effects of the hydration reaction of highly dispersed samples of secondary concrete have shown that this process is exothermic, the enthalpy of hydration of which is comparable to a similar parameter for cement. It was experimentally shown that fine powders of secondary concrete are effective as components of a composite binder, but they need to be pre-activated to optimal parameters, one of which is surface activity. In addition, the symbasis of changes in surface activity, the specific heat of the hydration reaction of highly dispersed concrete fractions and the compressive strength of fine-grained concrete samples made by using a composite binder containing a highly dispersed fraction of secondary concrete was established.

1948 ◽  
Vol 158 (1) ◽  
pp. 297-316
Author(s):  
W. T. Bottomley

Van Iterson's experiments show that cavitation erosion is produced by the collapse of minute air bubbles in water in a state of air supersaturation. This is contrary to the usual conception that cavitation erosion is due to the collapse of vapour bubbles. The author gives results of experiments which indicate that the bubbles which form and collapse at the stage of incipient cavitation in aerated water are air bubbles in a supersaturated state. The experiments also show that vapour bubbles which collapse in de-aerated water are in thermal equilibrium. It is shown that the collapse of bubbles in thermal equilibrium cannot cause erosion because the vapour pressure inside and the hydrostatic pressure surrounding the bubbles are balanced during collapse. The energy producing cavitation erosion is the free surface energy liberated by the collapse of the air bubbles. The final collapse velocity is the velocity of sound in water and the magnitude of the blow produced is of the order of 120 tons per sq. in. or more. The effect of these views on the interpretation of the model tests in cavitation tunnels and on the cavitation number is discussed.


2009 ◽  
Vol 50 (6) ◽  
pp. 1171-1176
Author(s):  
N. Yu. Sdobnyakov ◽  
A. N. Bazulev ◽  
V. M. Samsonov ◽  
D. A. Kul’pin ◽  
D. N. Sokolov

2019 ◽  
Vol 394 ◽  
pp. 1-4
Author(s):  
Valentina Ivanovna Loganina ◽  
Yerkebulan Bisengalievich Mazhitov ◽  
Yuri Petrovich Skachkov

The results of the study provide information on the resistance of coatings based on the solof silicate paint in the process of freezing and thawing. It was found, that coatings based on sol silicatepaints are characterized by a higher resistance compared of silicate coatings. It is shown, that thecoatings withstood 50 cycles of alternate freezing and thawing. The surface energy of the coatingswas calculated using the critical surface tension of the fluid at the interface with the solid. Thedispersion contribution in the intermolecular interaction between the particles of the coatings wasestimated. The values of the surface tension of the coatings and the values of the dispersioncomponent of the surface energy of the coatings — the complex Hamaker constant — are calculated.It was revealed, that after testing a decrease in the values of the Hamaker constant is observed. It wasestablished, that after testing for frost resistance, the values of the Hamaker constant for coatingsbased on sol of silicate paint are higher compared to coatings based on silicate paint.


2020 ◽  
Vol 47 (3) ◽  
pp. 223-231 ◽  
Author(s):  
Fabienne Suter ◽  
Spiros Zinelis ◽  
Raphael Patcas ◽  
Marc Schätzle ◽  
George Eliades ◽  
...  

Objective: The characterisation of surface roughness and energy of contemporary thermoplastic materials used in manufacturing of orthodontic aligners. Design: In vitro, laboratory study. Materials and methods: Four commercially available thermoplastic materials were selected (CA-medium/CAM, Essix-copopyester/COP, Duran/DUR and Erkodur/ERK). Five disks from each, as received, material were tested and subjected to: (1) reflected light microscopy; (2) optical profilometry for the estimation of Sa, Sz, Sq, Sdr, Sc, Sv surface roughness parameters (n = 5); and (3) contact angle measurements with a Zisman series of liquids for the estimation of critical surface tension (γC), total work of adhesion (WA), as well as the work of adhesion due to polar (WP) and dispersion (WD) components employing the Zisman method (n = 5/liquid). Thermoformed disks were prepared against a dental stone model and the roughness parameters were calculated again Statistical analysis was performed by one-way ANOVA/ Tukey multiple comparison test and t-test (a = 0.05). Results: Microscopic and profilometric analyses revealed a smooth surface texture in the as-received materials, but a very rough texture after thermoforming, with insignificant differences within each state. Significant differences in the as-received state were found in the surface energy parameters; CAM showed the lowest γC and the highest WA, WP, WD, whereas ERK with the highest γC demonstrated lower WA. COP and DUR were ranked in an intermediate group regarding γC, with a statistically significant difference in WA between them, mainly attributed to the lower WP of the former. Conclusion: Given the differences in surface energy parameters and the lack of roughness differences within the as received or thermoformed groups, it may be concluded that variations in the plaque retaining capacity are anticipated, determined by γC, WA and the WP, WD components.


2006 ◽  
Vol 252 (15) ◽  
pp. 5384-5386 ◽  
Author(s):  
S. Garruchet ◽  
O. Politano ◽  
J.M. Salazar ◽  
A. Hasnaoui ◽  
T. Montesin

2013 ◽  
Vol 6 (2) ◽  
pp. 157-159 ◽  
Author(s):  
I. A. Starostina ◽  
O. V. Stoyanov ◽  
N. V. Sokorova

Sign in / Sign up

Export Citation Format

Share Document