scholarly journals Fabrication of Fe-TiC Composite Powder by High-Energy Milling and Subsequent Reaction Synthesis

2013 ◽  
Vol 20 (1) ◽  
pp. 53-59 ◽  
Author(s):  
Ki-Bong Ahn ◽  
Byung-Hun Lee ◽  
Young-Hee Lee ◽  
Hyunh Xuan Khoa ◽  
Ji-Soon Kim
Keyword(s):  
Composite Powder ◽  
High Energy ◽  
Reaction Synthesis ◽  
Subsequent Reaction ◽  
High Energy Milling

scholarly journals Fabrication of Fe-TiB2Composite Powder by High-Energy Milling and Subsequent Reaction Synthesis

2013 ◽  
Vol 20 (3) ◽  
pp. 221-227 ◽  
Author(s):  
H.X. Khoa ◽  
N.Q. Tuan ◽  
Y.H. Lee ◽  
B.H. Lee ◽  
N.H. Viet ◽  
...  
Keyword(s):  
High Energy ◽  
Reaction Synthesis ◽  
Subsequent Reaction ◽  
High Energy Milling

Production of Al–20 wt.% Al2O3 composite powder using high energy milling

2009 ◽  
Vol 192 (3) ◽  
pp. 346-351 ◽  
Author(s):  
S.S. Razavi Tousi ◽  
R. Yazdani Rad ◽  
E. Salahi ◽  
I. Mobasherpour ◽  
M. Razavi
Keyword(s):  
Composite Powder ◽  
High Energy ◽  
High Energy Milling ◽  
Al2o3 Composite

Effect of high energy milling and compaction pressure on density of a sintered Nb–20%Cu composite powder

2015 ◽  
Vol 51 ◽  
pp. 207-211 ◽  
Author(s):  
Franciné Alves da Costa ◽  
Gilberto Melchiors ◽  
Uílame Umbelino Gomes ◽  
Angelus Giuseppe Pereira da Silva
Keyword(s):  
Composite Powder ◽  
Compaction Pressure ◽  
High Energy ◽  
High Energy Milling

Sintering under plasma of a Ta–20%Cu composite powder prepared by high energy milling

2008 ◽  
Vol 26 (3) ◽  
pp. 207-211 ◽  
Author(s):  
F.A. da Costa ◽  
J.F. da Silva ◽  
A.G.P. da Silva ◽  
U.U. Gomes ◽  
C. Alves
Keyword(s):  
Composite Powder ◽  
High Energy ◽  
High Energy Milling

Effect of Milling Time on Microstructure of CNTs/Al5083 Composites Powder by High Energy Milling

2014 ◽  
Vol 788 ◽  
pp. 608-612
Author(s):  
Zheng Li ◽  
Xiao Lan Cai ◽  
Feng Yi ◽  
Ming Jun Yu ◽  
Chui Hu
Keyword(s):  
Particle Size ◽  
Crystallite Size ◽  
Composite Powder ◽  
Milling Time ◽  
Average Crystallite Size ◽  
High Energy ◽  
High Energy Milling ◽  
Medium Particle ◽  
Medium Particle Size ◽  
Time Lead

The 2wt%CNTs/Al5083 composite powder was prepared by High Energy Milling, and the effect of the milling time on microstructure of the 2wt.%CNTs/Al5083 composite powder was investigated. The Microstructure was observed by SEM, TEM and XRD. The result showed that prolonging the milling time lead to the reduction of the Medium particle size D50. The best D50 was obtained at milling 2.5h with the particle size of 22.33μm. CNTs homogeneous embedded into the Al-matrix when the milling time was 2.5h. The average crystallite size of Al was 46.4nm after milling for 2.5h, and the average crystallite size of Al also increased as the recrystallization.

Nanostructured powders based on aluminum reinforced by silicon nitride designed for spraying of multifunctional strengthened coatings

2019 ◽  
pp. 65-73
Author(s):  
T. I. Bobkova ◽  
B. V. Farmakovsky ◽  
N. A. Sokolova
Keyword(s):  
Silicon Nitride ◽  
Composite Powder ◽  
High Energy ◽  
Cold Gas Dynamic Spraying ◽  
Powder Materials ◽  
Structure And Properties ◽  
Gas Dynamic ◽  
Composition Structure ◽  
New Phase ◽  
Nanostructured Powders

The work deals with topical issues such as development of composite nanostructured powder materials. The results of creating powders based on the system “aluminum–nitride of silicon” are presented. Complex investigations of the composition, structure and properties of powder materials, as well as coatings formed on their basis by supersonic cold gas dynamic spraying, were carried out. It has been found that the high-energy treatment of a powder mixture of aluminum with nanofibers of silicon nitride provides the formation of a composite powder in which a new phase of the Si(1-х)AlхO(1-х)Nх type is formed, which additionally increases the hardness in the coatings to be sprayed.

Impact of the SiC addition on the morphological, structural and mechanical properties of Cu-SiC composite powders prepared by high energy milling

2021 ◽  
Author(s):  
Nailton T. Câmara ◽  
Rafael A. Raimundo ◽  
Cleber S. Lourenço ◽  
Luís M.F. Morais ◽  
David D.S. Silva ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Energy ◽  
Composite Powders ◽  
High Energy Milling

Effect of High-Energy Milling and Sintering Temperature on the Properties of Al2O3-WC-Co Composites

2021 ◽  
Author(s):  
Heytor V. S. B. Azevêdo ◽  
Rafael A. Raimundo ◽  
David D. S. Silva ◽  
Luís M. F. Morais ◽  
Franciné A. Costa ◽  
...  
Keyword(s):  
Sintering Temperature ◽  
High Energy ◽  
High Energy Milling

Fabrication of (Y2O3)n–ZnO nanocomposites by high-energy milling as potential photocatalysts

2021 ◽  
Author(s):  
A. Modwi ◽  
M. A. Ben Aissa ◽  
Kamal K. Taha ◽  
L. Khezami ◽  
J. El Ghoul ◽  
...  
Keyword(s):  
High Energy ◽  
High Energy Milling
Sign in / Sign up

Export Citation Format

Share Document