Axial-Shear Force-Bending Moment Interaction in Elastoplastic Analysis of Steel Frames

2012 ◽  
Author(s):  
M.M.S. Manola ◽  
V.K. Koumousis
Keyword(s):  
Shear Force ◽  
Steel Frames ◽  
Bending Moment ◽  
Elastoplastic Analysis ◽  
Axial Shear ◽  
Moment Interaction

scholarly journals Statics And Kinematics Of Semirigid Steel Frames Under Seismic Action

2015 ◽  
Vol 5 (2) ◽  
pp. 59-64
Author(s):  
Aliz Mathe ◽  
Al. Cătărig ◽  
Ilinca Moldovan
Keyword(s):  
Shear Force ◽  
Degrees Of Freedom ◽  
Steel Frames ◽  
Time History ◽  
Bending Moment ◽  
Cyclic Behavior ◽  
Seismic Action ◽  
Base Shear ◽  
Planar Frames ◽  
Lumped Masses

Abstract Intended contribution emphasizes the statics and kinematics of semi-rigid steel frames seismically acted upon. The dynamic model of analyzed structures consists of multi degree of freedom systems with lumped masses located at floor levels. The dynamic degrees of freedom are the lateral seismically induced floor displacements. A cyclic behavior of semi-rigid beam – column connections associated with the four parameters analytical bending moment M – relative rotation θr is considered. Time history seismic analyses are performed on multi-story steel planar frames equipped with several top and seat and web angle beam – column connections acted upon by recorded seismic actions. The computed numerical results refer to the contrary static and effects of semi-rigidity: the increase in lateral floor displacements accompanied by a decrease in the seismic base shear force. Relevant comments are drawn.

Imperialist Competitive Algorithm for Multiobjective Optimization of Ellipsoidal Head of Pressure Vessel

2011 ◽  
Vol 110-116 ◽  
pp. 3422-3428 ◽  
Author(s):  
Behzad Abdi ◽  
Hamid Mozafari ◽  
Ayob Amran ◽  
Roya Kohandel
Keyword(s):  
Genetic Algorithm ◽  
Pressure Vessel ◽  
Shear Force ◽  
Minimum Weight ◽  
Bending Moment ◽  
Imperialist Competitive Algorithm ◽  
Optimum Shape ◽  
Working Pressure ◽  
Competitive Algorithm ◽  
Bending Stresses

This work devoted to an ellipsoidal head of pressure vessel under internal pressure load. The analysis is aimed at finding an optimum weight of ellipsoidal head of pressure vessel due to maximum working pressure that ensures its full charge with stresses by using imperialist competitive algorithm and genetic algorithm. In head of pressure vessel the region of its joint with the cylindrical shell is loaded with shear force and bending moments. The load causes high bending stresses in the region of the joint. Therefore, imperialist competitive algorithm was used here to find the optimum shape of a head with minimum weight and maximum working pressure which the shear force and the bending moment moved toward zero. Two different size ellipsoidal head examples are selected and studied. The imperialist competitive algorithm results are compared with the genetic algorithm results.

Application of the Mode-Acceleration Technique to the Solution of the Moving Oscillator Problem

1999 ◽  
Author(s):  
Alexander V. Pesterev ◽  
Lawrence A. Bergman
Keyword(s):  
Shear Force ◽  
Series Representation ◽  
Bending Moment ◽  
Static Solution ◽  
Distributed Parameter ◽  
Distributed Parameter System ◽  
Parameter System ◽  
One Dimensional ◽  
Acceleration Technique ◽  
Moving Oscillator

Abstract The problem of calculating the dynamic response of a one-dimensional distributed parameter system excited by an oscillator traversing the system with an arbitrarily varying speed is investigated. An improved series representation for the solution is derived that takes into account the jump in the shear force at the point of the attachment of the oscillator, which makes it possible to efficiently calculate the distributed shear force and, where applicable, bending moment. The improvement is achieved through the introduction of the “quasi-static” solution, an approximation to the desired one, which makes it possible to apply to the moving oscillator problem the “mode-acceleration” technique conventionally used for acceleration of series in problems related to the steady-state vibration of distributed systems. Numerical results illustrating the efficiency of the method are presented.

The Influence of Rotatory Inertia and Transverse Shear on the Dynamic Plastic Behavior of Beams

1979 ◽  
Vol 46 (2) ◽  
pp. 303-310 ◽  
Author(s):  
Norman Jones ◽  
J. Gomes de Oliveira
Keyword(s):  
Transverse Shear ◽  
Shear Force ◽  
Yield Criterion ◽  
Yield Condition ◽  
Bending Moment ◽  
Plastic Behavior ◽  
Plastic Response ◽  
Rotatory Inertia ◽  
Perfectly Plastic ◽  
Theoretical Procedure

The theoretical procedure presented herein examines the influence of retaining the transverse shear force in the yield criterion and rotatory inertia on the dynamic plastic response of beams. Exact theoretical rigid perfectly plastic solutions are presented for a long beam impacted by a mass and a simply supported beam loaded impulsively. It transpires that rotatory inertia might play a small, but not negligible, role on the response of these beams. The results in the various figures indicate that the greatest departure from an analysis which neglects rotatory inertia but retains the influence of the bending moment and transverse shear force in the yield condition is approximately 11 percent for the particular range of parameters considered.

Three-dimensional association of bending moment and shear force deformable panels

2001 ◽  
Vol 10 (1) ◽  
pp. 27-42 ◽  
Author(s):  
Eddie Mancini ◽  
Walter Savassi
Keyword(s):  
Shear Force ◽  
Three Dimensional ◽  
Bending Moment
Sign in / Sign up

Export Citation Format

Share Document