scholarly journals Collection efficiency of <i>α</i>-pinene secondary organic aerosol particles explored via light-scattering single-particle aerosol mass spectrometry

2017 ◽  
Vol 10 (3) ◽  
pp. 1139-1154 ◽  
Author(s):  
Ellis Shipley Robinson ◽  
Timothy B. Onasch ◽  
Douglas Worsnop ◽  
Neil M. Donahue
Keyword(s):  
Light Scattering ◽  
Single Particle ◽  
Secondary Organic Aerosol ◽  
Collection Efficiency ◽  
Organic Aerosol ◽  
Ionization Efficiency ◽  
Signal Delay ◽  
Aerosol Mass ◽  
The Mean ◽  
Effective Ionization

Abstract. We investigated the collection efficiency and effective ionization efficiency for secondary organic aerosol (SOA) particles made from α-pinene + O3 using the single-particle capabilities of the aerosol mass spectrometer (AMS). The mean count-based collection efficiency (CEp) for SOA across these experiments is 0.30 (±0.04 SD), ranging from 0.25 to 0.40. The mean mass-based collection efficiency (CEm) is 0.49 (±0.07 SD). This sub-unit collection efficiency and delayed vaporization is attributable to particle bounce in the vaporization region. Using the coupled optical and chemical detection of the light-scattering single-particle (LSSP) module of the AMS, we provide clear evidence that delayed vaporization is somewhat of a misnomer for these particles: SOA particles measured as a part of the AMS mass distribution do not vaporize at a slow rate; rather, they flash-vaporize, albeit often not on the initial impact with the vaporizer but instead upon a subsequent impact with a hot surface in the vaporization region. We also find that the effective ionization efficiency (defined as ions per particle, IPP) decreases with delayed arrival time. CEp is not a function of particle size (for the mobility diameter range investigated, 170–460 nm), but we did see a decrease in CEp with thermodenuder temperature, implying that oxidation state and/or volatility can affect CEp for SOA. By measuring the mean ions per particle produced for monodisperse particles as a function of signal delay time, we can separately determine CEp and CEm and thus more accurately measure the relative ionization efficiency (compared to ammonium nitrate) of different particle types.

scholarly journals Collection efficiency of α-pinene secondary organic aerosol particles explored via light scattering single particle aerosol mass spectrometry

2016 ◽  
Author(s):  
Ellis Shipley Robinson ◽  
Timothy B. Onasch ◽  
Douglas Worsnop ◽  
Neil M. Donahue
Keyword(s):  
Light Scattering ◽  
Single Particle ◽  
Secondary Organic Aerosol ◽  
Collection Efficiency ◽  
Organic Aerosol ◽  
Ionization Efficiency ◽  
Aerosol Mass ◽  
The Mean ◽  
Hot Surface ◽  
Effective Ionization

Abstract. We investigated the collection efficiency and effective ionization efficiency for secondary organic aerosol (SOA) particles made from α-pinene &amp;plus; O3 using the single-particle capabilities of the Aerosol Mass Spectrometer (AMS). The mean count-based collection efficiency (CEp) for SOA across these experiments is 0.30 (±0.04 S.D.), ranging from 0.25 to 0.40. The mean mass-based collection efficiency (CEm) is 0.49 (±0.07 S.D.). This sub-unit collection efficiency and delayed vaporization is attributable to particle bounce in the vaporization region. Using the coupled optical and chemical detection of the light scattering single-particle (LSSP) module 5 of the AMS, we provide clear evidence that ''delayed vaporization'' is somewhat of a misnomer for these particles: SOA particles that appear within the chopper window do not vaporize at a slow rate; rather, they flash-vaporize, but often not on the initial impact with the vaporizer, and instead upon a subsequent impact with a hot surface in the vaporization region. We also find that the effective ionization efficiency (defined as ions per particle, IPP) decreases with delayed arrival time. CEp is not a function of particle size (for the mobility diameter range investigated, 170–460 nm), but we did see a decrease in CEp with thermodenuder temperature, implying that oxidation state and/or volatility can affect CEp for SOA.

scholarly journals Single-particle measurements of bouncing particles and in situ collection efficiency from an airborne aerosol mass spectrometer (AMS) with light-scattering detection

2017 ◽  
Vol 10 (10) ◽  
pp. 3801-3820 ◽  
Author(s):  
Jin Liao ◽  
Charles A. Brock ◽  
Daniel M. Murphy ◽  
Donna T. Sueper ◽  
André Welti ◽  
...  
Keyword(s):  
Light Scattering ◽  
Mass Spectrometer ◽  
Single Particle ◽  
Total Mass ◽  
Mass Spectra ◽  
Collection Efficiency ◽  
Aerosol Mass Spectrometer ◽  
Mass Spectral ◽  
Aerosol Mass ◽  
Spectral Signal

Abstract. A light-scattering module was coupled to an airborne, compact time-of-flight aerosol mass spectrometer (LS-AMS) to investigate collection efficiency (CE) while obtaining nonrefractory aerosol chemical composition measurements during the Southeast Nexus (SENEX) campaign. In this instrument, particles scatter light from an internal laser beam and trigger saving individual particle mass spectra. Nearly all of the single-particle data with mass spectra that were triggered by scattered light signals were from particles larger than ∼ 280 nm in vacuum aerodynamic diameter. Over 33 000 particles are characterized as either prompt (27 %), delayed (15 %), or null (58 %), according to the time and intensity of their total mass spectral signals. The particle mass from single-particle spectra is proportional to that derived from the light-scattering diameter (dva-LS) but not to that from the particle time-of-flight (PToF) diameter (dva-MS) from the time of the maximum mass spectral signal. The total mass spectral signal from delayed particles was about 80 % of that from prompt ones for the same dva-LS. Both field and laboratory data indicate that the relative intensities of various ions in the prompt spectra show more fragmentation compared to the delayed spectra. The particles with a delayed mass spectral signal likely bounced off the vaporizer and vaporized later on another surface within the confines of the ionization source. Because delayed particles are detected by the mass spectrometer later than expected from their dva-LS size, they can affect the interpretation of particle size (PToF) mass distributions, especially at larger sizes. The CE, measured by the average number or mass fractions of particles optically detected that had measurable mass spectra, varied significantly (0.2–0.9) in different air masses. The measured CE agreed well with a previous parameterization when CE > 0.5 for acidic particles but was sometimes lower than the minimum parameterized CE of 0.5.

scholarly journals Single particle characterization using a light scattering module coupled to a time-of-flight aerosol mass spectrometer

2009 ◽  
Vol 9 (20) ◽  
pp. 7769-7793 ◽  
Author(s):  
E. S. Cross ◽  
T. B. Onasch ◽  
M. Canagaratna ◽  
J. T. Jayne ◽  
J. Kimmel ◽  
...  
Keyword(s):  
Light Scattering ◽  
Mass Spectrometer ◽  
Single Particle ◽  
Collection Efficiency ◽  
Time Of Flight ◽  
Chemical Compositions ◽  
Single Particles ◽  
Mixing State ◽  
Aerosol Mass Spectrometer ◽  
Aerosol Mass

Abstract. We present the first single particle results obtained with an Aerodyne time-of-flight aerosol mass spectrometer coupled with a light scattering module (LS-ToF-AMS). The instrument was deployed at the T1 ground site approximately 40 km northeast of the Mexico City Metropolitan Area as part of the MILAGRO field study in March of 2006. The LS-ToF-AMS acquires both ensemble average and single particle data. Over a 75-h sampling period from 27–30 March 2006, 12 853 single particle mass spectra were optically-triggered and saved. The single particles were classified based on observed vaporization histories and measured chemical compositions. The single particle data is shown to provide insights on internal AMS collection efficiencies and ambient mixing state information that augments the ensemble data. Detection of correlated light scattering and chemical ion signals allowed for a detailed examination of the vaporization/ionization process for single particles measured with the AMS instrument. Three particle vaporization event types were identified as a fraction of the total number of particles detected: (1) 23% with prompt vaporization, (2) 26% with delayed vaporization, and (3) 51% characterized as null. Internal consistency checks show that average single particle nonrefractory mass and chemical composition measurements were in reasonable agreement with ensemble measurements and suggest that delayed and null vaporization events are the dominant source of the nonunit collection efficiency of the AMS. Taken together, the simultaneous prompt single particle and aerosol ensemble measurements offer insight into the mixing state and atmospheric transformations of ambient aerosol particles.

scholarly journals Secondary organic aerosol formation from biomass burning emissions

2019 ◽  
Author(s):  
Christopher Y. Lim ◽  
David H. Hagan ◽  
Matthew M. Coggon ◽  
Abigail R. Koss ◽  
Kanako Sekimoto ◽  
...  
Keyword(s):  
Biomass Burning ◽  
Secondary Organic Aerosol ◽  
Total Concentration ◽  
Organic Aerosol ◽  
Oh Radicals ◽  
Aerosol Formation ◽  
Atmospheric Aging ◽  
Aerosol Mass ◽  
Photochemical Aging ◽  
Organic Gases

Abstract. Biomass burning is an important source of aerosol and trace gases to the atmosphere, but how these emissions change chemically during their lifetimes is not fully understood. As part of the Fire Influence on Regional and Global Environments Experiment (FIREX 2016), we investigated the effect of photochemical aging on biomass burning organic aerosol (BBOA), with a focus on fuels from the western United States. Emissions were sampled into a small (150 L) environmental chamber and photochemically aged via the addition of ozone and irradiation by 254 nm light. While some fraction of species undergoes photolysis, the vast majority of aging occurs via reaction with OH radicals, with total OH exposures corresponding to the equivalent of up to 10 days of atmospheric oxidation. For all fuels burned, large and rapid changes are seen in the ensemble chemical composition of BBOA, as measured by an aerosol mass spectrometer (AMS). Secondary organic aerosol (SOA) formation is seen for all aging experiments and continues to grow with increasing OH exposure, but the magnitude of the SOA formation is highly variable between experiments. This variability can be explained well by a combination of experiment-to-experiment differences in OH exposure and the total concentration of non-methane organic gases (NMOGs) in the chamber before oxidation, measured by PTR-ToF-MS (r2 values from 0.64 to 0.83). From this relationship, we calculate the fraction of carbon from biomass burning NMOGs that is converted to SOA as a function of equivalent atmospheric aging time, with carbon yields ranging from 24 ± 4 % after 6 hours to 56 ± 9 % after 4 days.

scholarly journals Particle-bound reactive oxygen species (PB-ROS) emissions and formation pathways in residential wood smoke under different combustion and aging conditions

2018 ◽  
Vol 18 (10) ◽  
pp. 6985-7000 ◽  
Author(s):  
Jun Zhou ◽  
Peter Zotter ◽  
Emily A. Bruns ◽  
Giulia Stefenelli ◽  
Deepika Bhattu ◽  
...  
Keyword(s):  
Reactive Oxygen Species ◽  
Regression Model ◽  
Secondary Organic Aerosol ◽  
Organic Aerosol ◽  
Oxygen Species ◽  
Wood Combustion ◽  
Aerosol Mass ◽  
Combustion Emissions ◽  
Aging Conditions ◽  
Combustion Regimes

Abstract. Wood combustion emissions can induce oxidative stress in the human respiratory tract by reactive oxygen species (ROS) in the aerosol particles, which are emitted either directly or formed through oxidation in the atmosphere. To improve our understanding of the particle-bound ROS (PB-ROS) generation potential of wood combustion emissions, a suite of smog chamber (SC) and potential aerosol mass (PAM) chamber experiments were conducted under well-determined conditions for different combustion devices and technologies, different fuel types, operation methods, combustion regimes, combustion phases, and aging conditions. The PB-ROS content and the chemical properties of the aerosols were quantified by a novel ROS analyzer using the DCFH (2′,7′-dichlorofluorescin) assay and a high-resolution time-of-flight aerosol mass spectrometer (HR-ToF-AMS). For all eight combustion devices tested, primary PB-ROS concentrations substantially increased upon aging. The level of primary and aged PB-ROS emission factors (EFROS) were dominated by the combustion device (within different combustion technologies) and to a greater extent by the combustion regimes: the variability within one device was much higher than the variability of EFROS from different devices. Aged EFROS under bad combustion conditions were ∼ 2–80 times higher than under optimum combustion conditions. EFROS from automatically operated combustion devices were on average 1 order of magnitude lower than those from manually operated devices, which indicates that automatic combustion devices operated at optimum conditions to achieve near-complete combustion should be employed to minimize PB-ROS emissions. The use of an electrostatic precipitator decreased the primary and aged ROS emissions by a factor of ∼ 1.5 which is however still within the burn-to-burn variability. The parameters controlling the PB-ROS formation in secondary organic aerosol were investigated by employing a regression model, including the fractions of the mass-to-charge ratios m∕z 44 and 43 in secondary organic aerosol (SOA; f44−SOA and f43−SOA), the OH exposure, and the total organic aerosol mass. The regression model results of the SC and PAM chamber aging experiments indicate that the PB-ROS content in SOA seems to increase with the SOA oxidation state, which initially increases with OH exposure and decreases with the additional partitioning of semi-volatile components with lower PB-ROS content at higher OA concentrations, while further aging seems to result in a decay of PB-ROS. The results and the special data analysis methods deployed in this study could provide a model for PB-ROS analysis of further wood or other combustion studies investigating different combustion conditions and aging methods.

scholarly journals Constraining condensed-phase formation kinetics of secondary organic aerosol components from isoprene epoxydiols

2016 ◽  
Vol 16 (3) ◽  
pp. 1245-1254 ◽  
Author(s):  
T. P. Riedel ◽  
Y.-H. Lin ◽  
Z. Zhang ◽  
K. Chu ◽  
J. A. Thornton ◽  
...  
Keyword(s):  
Aqueous Phase ◽  
Atmospheric Aerosols ◽  
Rate Constants ◽  
Reaction Rate ◽  
Secondary Organic Aerosol ◽  
Organic Aerosol ◽  
Heterogeneous Reactions ◽  
Model Calculations ◽  
Reaction Rate Constants ◽  
Aerosol Mass

Abstract. Isomeric epoxydiols from isoprene photooxidation (IEPOX) have been shown to produce substantial amounts of secondary organic aerosol (SOA) mass and are therefore considered a major isoprene-derived SOA precursor. Heterogeneous reactions of IEPOX on atmospheric aerosols form various aerosol-phase components or "tracers" that contribute to the SOA mass burden. A limited number of the reaction rate constants for these acid-catalyzed aqueous-phase tracer formation reactions have been constrained through bulk laboratory measurements. We have designed a chemical box model with multiple experimental constraints to explicitly simulate gas- and aqueous-phase reactions during chamber experiments of SOA growth from IEPOX uptake onto acidic sulfate aerosol. The model is constrained by measurements of the IEPOX reactive uptake coefficient, IEPOX and aerosol chamber wall losses, chamber-measured aerosol mass and surface area concentrations, aerosol thermodynamic model calculations, and offline filter-based measurements of SOA tracers. By requiring the model output to match the SOA growth and offline filter measurements collected during the chamber experiments, we derive estimates of the tracer formation reaction rate constants that have not yet been measured or estimated for bulk solutions.

scholarly journals Secondary organic aerosol formation from reaction of tertiary amines with nitrate radical

2008 ◽  
Vol 8 (4) ◽  
pp. 16585-16608 ◽  
Author(s):  
M. E. Erupe ◽  
D. J. Price ◽  
P. J. Silva ◽  
Q. G. J. Malloy ◽  
L. Qi ◽  
...  
Keyword(s):  
Mass Spectrometer ◽  
Secondary Organic Aerosol ◽  
Organic Aerosol ◽  
Nitrate Radical ◽  
Tertiary Amines ◽  
Aerosol Formation ◽  
Night Time ◽  
Aerosol Mass Spectrometer ◽  
Aerosol Mass ◽  
Secondary Organic Aerosol Formation

Abstract. Secondary organic aerosol formation from the reaction of tertiary amines with nitrate radical was investigated in an indoor environmental chamber. Particle chemistry was monitored using a high resolution aerosol mass spectrometer while gas-phase species were detected using a proton transfer reaction mass spectrometer. Trimethylamine, triethylamine and tributylamine were studied. Results indicate that tributylamine forms the most aerosol mass followed by trimethylamine and triethylamine respectively. Spectra from the aerosol mass spectrometer indicate the formation of complex non-salt aerosol products. We propose a reaction mechanism that proceeds via abstraction of a proton by nitrate radical followed by RO2 chemistry. Rearrangement of the aminyl alkoxy radical through hydrogen shift leads to the formation of hydroxylated amides, which explain most of the higher mass ions in the mass spectra. These experiments show that oxidation of tertiary amines by nitrate radical may be an important night-time source of secondary organic aerosol.

Sign in / Sign up

Export Citation Format

Share Document