scholarly journals Local Corrosion of Austenitic Steels and Alloys

2017 ◽  
Author(s):  
Pisarevskiy Lev Alexandrovich ◽  
Filippov Georgiy Anatolievich
Keyword(s):  
Austenitic Steels ◽  
Local Corrosion

scholarly journals Local corrosion of austenitic steels and alloys for heat exchanger tubes of nuclear power stations steam generators

2019 ◽  
Vol 75 (2) ◽  
pp. 227-241 ◽  
Author(s):  
L. A. Pisarevskii ◽  
A. B. Korostelev ◽  
A. A. Lipatov ◽  
G. A. Filippov ◽  
T. Yu. Kin
Keyword(s):  
Thermal Aging ◽  
Nuclear Power ◽  
Austenitic Steels ◽  
Local Corrosion ◽  
Nickel Steel ◽  
Water Type ◽  
Low Carbon ◽  
Steam Generators ◽  
Power Stations

Elaboration of modern domestic structural materials with increased corrosion resistance in contact with advanced heatcarriers of future reactor plants is an important problem at development of innovation projects of nuclear power engineering. Heatexchanging tubes are the critical components, which influence on the safety and reliability of steam generators operation. Corrosion properties of non-stabilized nitrogen-containing corrosion resistant steels of austenite class after cold deformation, thermal treatment and long-term thermal aging studied. It was shown, that silicon introducing into chrome-nickel steel, alloyed by nitrogen and molybdenum, results in increasing of its resistance against local kinds of corrosion and equated it on resistance against intercrystallite and pitting corrosion with particularly low-carbon steels and alloys. But the experimental 03Х18Н13С2АМ2ВФБР-Ш low carbon micro-alloyed steel, proposed for operation at a heat-carrier temperature of 450–500 о С, in the first version had a tendency to a decrease of resistance against local corrosion and impact resistance after long-term thermal aging at temperatures of 360 о С and higher. At present specifying of technological parameters of production and balanced alloying element content takes place, which prevents heat exchanging tubes properties degradation. Steel 03Х17Н13С2АМ2 which has higher resistance against local corrosion and strength comparing with 316LN and 08Х18Н10Т grades, can be taken as a candidate material for production of heat-exchanging tubes of steam generators of nuclear power stations having power reactors of water-water type. The new 03Х17Н9АС2 steel, resistant against inter-crystallite corrosion in high-oxidizing media, was proposed for tests of its operation under conditions of contact with lead heat-carriers instead of 10Х15Н9С3Б1-Ш (ЭП 302-Ш) steel.

Effect of N, Mo, and Si on Local Corrosion Resistance of Unstabilized Cr–Ni and Cr–Mn–Ni Austenitic Steels

Metallurgist ◽  
2016 ◽  
Vol 60 (7-8) ◽  
pp. 822-831 ◽  
Author(s):  
L. A. Pisarevskii ◽  
G. A. Filippov ◽  
A. A. Lipatov
Keyword(s):  
Corrosion Resistance ◽  
Austenitic Steels ◽  
Local Corrosion

Microstructures of Ti-1.5 w/o Ni Alloys with Mo and A1 Additions

1975 ◽  
Vol 33 ◽  
pp. 54-55
Author(s):  
Anna C. Fraker
Keyword(s):  
Corrosion Resistance ◽  
Beneficial Effect ◽  
Crevice Corrosion ◽  
Local Corrosion ◽  
Precipitate Size ◽  
Ni Alloys

Small amounts of nickel are added to titanium to improve the crevice corrosion resistance but this results in an alloy which has sheet fabrication difficulties and is subject to the formation of large Ti2Ni precipitates. These large precipitates can serve as local corrosion sites; but in a smaller more widely dispersed form, they can have a beneficial effect on crevice corrosion resistance. The purpose of the present work is to show that the addition of a small amount of Mo to the Ti-1.5Ni alloy reduces the Ti2Ni precipitate size and produces a more elongated grained microstructure. It has recently been reported that small additions of Mo to Ti-0.8 to lw/o Ni alloys produce good crevice corrosion resistance and improved fabrication properties.

CONSTITUTIVE FLOW RELATIONS FOR AUSTENITIC STEELS DURING STRAININDUCED MARTENSITIC TRANSFORMATION

1982 ◽  
Vol 43 (C4) ◽  
pp. C4-429-C4-434 ◽  
Author(s):  
T. Narutani ◽  
G. B. Olson ◽  
M. Cohen
Keyword(s):  
Martensitic Transformation ◽  
Austenitic Steels

Descaling of austenitic steels by laser radiation

1994 ◽  
Author(s):  
H. Schlüter ◽  
A. Zwick ◽  
M. Aden ◽  
G. Uhlig ◽  
K. Wissenbach ◽  
...  
Keyword(s):  
Laser Radiation ◽  
Austenitic Steels

Activity of Nitrogen in Austenitic Steels

1975 ◽  
Vol 61 (13) ◽  
pp. 2892-2903 ◽  
Author(s):  
Makoto KIKUCHI ◽  
Ryohei TANAKA
Keyword(s):  
Austenitic Steels

NIROSTA 4305

Alloy Digest ◽  
2002 ◽  
Vol 51 (5) ◽  
Keyword(s):  
Corrosion Resistance ◽  
Physical Properties ◽  
Tungsten Carbide ◽  
Tensile Properties ◽  
High Speed ◽  
High Speed Steel ◽  
Heat Treating ◽  
Austenitic Steels ◽  
High Sulfur Content ◽  
Machined Parts

Abstract NIROSTA 4305 is an austenitic alloy with a high sulfur content. The alloy is typically used for machined parts. As with other austenitic steels, it is necessary to machine with good-quality high-speed steel or tungsten carbide tools. This datasheet provides information on composition, physical properties, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: SS-854. Producer or source: ThyssenKrupp Nirosta GmbH.

ALLEGHENY LUDLUM TYPE 205

Alloy Digest ◽  
1997 ◽  
Vol 46 (10) ◽  
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Corrosion Resistance ◽  
Physical Properties ◽  
Tensile Properties ◽  
Magnetic Permeability ◽  
Cold Working ◽  
High Strength ◽  
Heat Treating ◽  
Austenitic Steels

Abstract Allegheny Stainless Type 205 is a chromium-manganese nitrogen austenitic high strength stainless steel that maintains its low magnetic permeability even after large amounts of cold working. Annealed Type 205 has higher mechanical properties than any of the conventional austenitic steels-and for any given strength level, the ductility of Type 205 is comparable to that of Type 301. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fatigue. It also includes information on corrosion resistance as well as heat treating, machining, and joining. Filing Code: SS-640. Producer or source: Allegheny Ludlum Corporation. Originally published March 1996, revised October 1997.

Sign in / Sign up

Export Citation Format

Share Document