Electrically Tunable Lens (ETL)-Based Variable Focus Imaging System for Parametric Surface Texture Analysis of Materials

Electrically tunable lenses (ETLs) are those with the ability to alter their optical power in response to an electric signal. This feature allows such systems to not only image the areas of interest but also obtain spatial depth perception (depth of field, DOF). The aim of the present study was to develop an ETL-based imaging system for quantitative surface analysis. Firstly, the system was calibrated to achieve high depth resolution, warranting the accurate measurement of the depth and to account for and correct any influences from external factors on the ETL. This was completed using the Tenengrad operator which effectively identified the plane of best focus as demonstrated by the linear relationship between the control current applied to the ETL and the height at which the optical system focuses. The system was then employed to measure amplitude, spatial, hybrid, and volume surface texture parameters of a model material (pharmaceutical dosage form) which were validated against the parameters obtained using a previously validated surface texture analysis technique, optical profilometry. There were no statistically significant differences between the surface texture parameters measured by the techniques, highlighting the potential application of ETL-based imaging systems as an easily adaptable and low-cost alternative surface texture analysis technique to conventional microscopy techniques.

Three-Dimensional Surface Texture Analysis of Fluoride’s Effect on Enamel Erosion

Enamel erosion has become a common clinical finding that often impairs dental esthetics and function. In the current study, we aimed to implement the three-dimensional surface texture analysis (3DST) method to explore the protective effect of fluoride on surface texture prior to erosive conditions. For each of the 50 teeth used in this study, the polished buccal enamel surface was divided into three separate areas: the first area was untouched polished enamel, the two other surfaces were immersed in 0.3% citric acid for 30 s. One was treated with high-concentration (19,000 ppm) sodium fluoride (NaF) solution prior to acid attack, and the other had no treatment prior to acid exposure. Enamel surface texture and step height measurements were obtained using a high-resolution disk scanning confocal microscope, and SEM images were also acquired. Surfaces treated with fluoride showed fewer variations in 3-D surface texture parameters than the eroded surface compared to the control group (p = 0.001). This was in accordance with the SEM descriptive images. The findings indicate that pre-fluoridated enamel areas were less affected by the acid and showed similar features to the untouched enamel. Moreover, a protective effect of the fluoride treatment against irreversible enamel damage was noted as the surface loss (step-height) was significantly reduced (p = 0.03). The study showed that 3DST analysis is a valuable methodology for detecting and quantifying subtle differences between the surfaces. When exploring the combination of all surface texture parameters, it was revealed that the pre-fluoridated eroded enamel surfaces showed considerable similarity to the untouched enamel.

Surface texture analysis of the X5CrNi18-10 steel after cutting with abrasive water jet and photon beam (laser)

The article presents an analysis of the geometric structure of the surface of X5CrNi18‑10 steel sheet after cutting with a abrasive water-jet (AWJ) and a photon beam (laser). Both methods and the workpiece material were also described. Using the laser triangulation method, the cut surface texture was measured by opto-digital microscopy. Additionally, microscopic images of the cut surface were made using the Dino-Lite Edge AM7915MZT microscope by ANMO Electronics Co. The analysis of changes in the value of the Sa parameter for the surface after laser cutting and abrasive water-jet showed that the thickness of the cut material has the most significant influence on the obtained measurement results.

Effects of different irrigation protocols on dentin surfaces as revealed through quantitative 3D surface texture analysis

The combination of ethylenediaminetetraacetic acid (EDTA) and sodium hypochlorite (NaOCl) has been advocated as an effective irrigation methodology to remove organic and inorganic matter in root canal therapy. Yet, it was suggested that both solutions might lead to structural changes of the dentinal wall surface, depending on the order of application which might affect sealer mechanical retention. This study aims to evaluate the effect of different irrigating protocols on dentin surface roughness using quantitative 3D surface texture analysis. Data stems from 150 human root dentin sections, divided into five groups, each prepared according to one of the following protocols: Negative control; 17% EDTA; 17% EDTA followed by 5.25% NaOCl; 5.25% NaOCl; and 5.25% NaOCl followed by 17% EDTA. Each dentin sample was examined for its three-dimensional surface texture using a high-resolution confocal disc-scanning measuring system. EDTA 17% and the combined EDTA 17% with NaOCl 5.25% showed considerably higher roughness properties compared to the control and to NaOCl 5.25% alone. However, the irrigation sequence did not affect the dentin roughness properties. Therefore, mechanical retention is probably not dependent upon the selection of irrigation protocol sequence.

A method for the taphonomic assessment of bone tools using 3D surface texture analysis of bone microtopography

Increasingly researchers have employed confocal microscopy and 3D surface texture analysis to assess bone surface modifications in an effort to understand ancient behavior. However, quantitative comparisons between the surfaces of purported archaeological bone tools and experimentally manufactured and used bones are complicated by taphonomic processes affecting ancient bone. Nonetheless, it may be reasonable to assume that bones within the same deposits are altered similarly and thus these alterations are quantifiable. Here we show how unworked bones can be used to quantify the taphonomic effect on bone surfaces and how this effect can then be controlled for and incorporated into an analysis for evaluating the modified surfaces of purported bone tools. To assess the baseline taphonomy of Middle Paleolithic archaeological deposits associated with typologically identified bone artifacts, specifically lissoirs, we directly compare the surface textures of ancient and modern unworked ribs. We then compare the ancient unworked ribs and lissoirs to assess their differences and predict the ancient artifacts’ original surface state using a multilevel multivariate Bayesian model. Our findings demonstrate that three of five tested surface texture parameters (Sa, Spc, and IsT) are useful for distinguishing surface type. Our model predictions show that lissoirs tend to be less rough, have more rounded surface peaks, and exhibit more directionally oriented surfaces. These characteristics are likely due to anthropogenic modifications and would have been more pronounced at deposition. Quantifying taphonomic alterations moves us one step closer to accurately assessing how bone artifacts were made and used in the ancient past.