Research on Protection Methods of Embedded Operating System Software Based on Hardware Compiler

2013 ◽  
Vol 443 ◽  
pp. 556-560
Author(s):  
Gao Ming He
Keyword(s):  
Operating System ◽  
Practical Significance ◽  
Embedded Operating System ◽  
System Software ◽  
Software Protection ◽  
Performance Loss ◽  
Cycle Simulation ◽  
Protection Technology ◽  
Program Flow ◽  
High Level

This paper describes a system; CODESSEAL can provide protection and evaluation to system software. CODESSEAL was designed to protect embedded systems with sufficient expertise and resources to capture attack equipment and manipulator, not only to protect software but also to protect hardware. By using the reconfigurable hardware allows CODESSEAL to provide confidentiality, integrity of security services and a platform-independent program flow without having to redesign the processor. System uses software and data protection technology and designs cycle simulation methods for data analysis. Experimental results show that the protected instructions and data with a high level of safety can be realized a low, which in most cases the performance loss can be reduced to below 10%, so the research of software protection methods of the embedded operating system of hardware compiler has important practical significance.

Thickness Indirect Measurement Method for Direct Pulling Pilot Cold Rolling Mill

2011 ◽  
Vol 189-193 ◽  
pp. 2670-2674
Author(s):  
Zhi Jie Jiao ◽  
Chun Yu He ◽  
Jian Ping Li ◽  
Xiang Hua Liu
Keyword(s):  
Cold Rolling ◽  
Rolling Mill ◽  
Measurement Method ◽  
Rolling Process ◽  
Indirect Measurement ◽  
Cold Rolling Mill ◽  
Movement Data ◽  
Program Flow ◽  
New Type ◽  
Exit Speed

Pilot cold rolling mill is the important tool for the cold rolling process researching and new steel grade development. According to the design of the new type direct pulling pilot cold rolling mill, based on the mass flow constant principle, strip exit thickness indirect measurement method is studied. During rolling, strip entry and exit speed can be calculated accurately according to the measured value of two sides’ clamps movement. Data filtering treatment is adopted and program flow chart is designed. Based on the material entry thickness measured manually, exit thickness of all passes can be measured indirectly. This thickness indirect measurement method has been applied successfully on the new type pilot cold rolling mill, and the measurement results show that this method has a good accuracy.

Making Decisions About...and Planning Program Flow

2010 ◽  
pp. 57-80
Author(s):  
Gary Bennett ◽  
Mitch Fisher ◽  
Brad Lees
Keyword(s):  
Planning Program ◽  
Program Flow

KW Level Wind Turbine Wind Tracking and Yaw System

2011 ◽  
Vol 148-149 ◽  
pp. 97-100
Author(s):  
Xu Gang Wang ◽  
Guang Qi Cao ◽  
Zhi Guang Guan ◽  
Zu Yu Zhao
Keyword(s):  
Wind Turbine ◽  
Wind Power ◽  
Fossil Fuels ◽  
Control Strategies ◽  
Low Cost ◽  
Control Program ◽  
Clean Energy ◽  
New Energy ◽  
Program Flow ◽  
And Control

Wind power is an important direction of new energy, which has no pollution, no consuming fossil fuels, and no producing waste, which is widely used at this stage of clean energy. The small stand alone wind power has been paid more and more attention due to its low cost, flexible installation, strong adaptability. This paper introduces the mechanical and electrical structure, which are used in KW level stand alone mode wind turbine automatically track and yaw system. The motion rules and control strategies of the tracking and yaw system are discussed and then the control program flow is provided. The PIC16F873 chip is used as controller for this part in this system. It can fully meet the design requirements, which will reduce costs and increase the system's control ability. This system can automatically track and yaw, according to the wind direction and wind power.

Sign in / Sign up

Export Citation Format

Share Document