Electrical conductivity and major mechanical and thermal properties of carbon nanotube-filled polyurethane foams

2011 ◽  
Vol 120 (5) ◽  
pp. 3014-3019 ◽  
Author(s):  
Ding-Xiang Yan ◽  
Kun Dai ◽  
Zhi-Dong Xiang ◽  
Zhong-Ming Li ◽  
Xu Ji ◽  
...  
Keyword(s):  
Electrical Conductivity ◽  
Thermal Properties ◽  
Carbon Nanotube ◽  
Polyurethane Foams ◽  
Mechanical And Thermal Properties

Electro-Mechanical and Thermal Properties of Multiwalled Carbon Nanotube Reinforced Alumina Composites

2008 ◽  
Vol 368-372 ◽  
pp. 701-703 ◽  
Author(s):  
Kaleem Ahmad ◽  
Wei Pan ◽  
Chun Lei Wan
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Electrical Conductivity ◽  
Thermal Properties ◽  
Carbon Nanotube ◽  
Mechanical And Thermal Properties ◽  
Multiwalled Carbon ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Alumina Composites

Multi-walled carbon nanotube (MWNT) reinforced alumina composites with different MWNT contents (5 and 10 vol %) were fabricated by spark plasma sintering. The room temperature dc electrical conductivity, thermal conductivity, and mechanical properties were investigated. Results showed that the electrical conductivity has improved around twelve orders of magnitude by addition of 5 vol% of MWNT. The fracture toughness changed from 3.2 to 4.4 MPa m1/2 with 39% improvement over monolithic Al2O3. The thermal conductivity decreased with increase of MWNT contents. The low values of thermal conductivity suggest that interfacial thermal barrier play an important role in determining these properties. MWNT can be used to improve concurrently electrical, mechanical properties of Al2O3 but with lower values of thermal properties.

Comparative study of single‐layer graphene and single‐walled carbon nanotube‐filled epoxy nanocomposites based on mechanical and thermal properties

2018 ◽  
Vol 40 (S2) ◽  
pp. E1840-E1849 ◽  
Author(s):  
Muhammad Razlan Zakaria ◽  
Muhammad Helmi Abdul Kudus ◽  
Hazizan Md Akil ◽  
Mohd Zharif Mohd Thirmizir ◽  
Muhammad Fadhirul Izwan Abdul Malik ◽  
...  
Keyword(s):  
Thermal Properties ◽  
Carbon Nanotube ◽  
Comparative Study ◽  
Single Layer ◽  
Single Layer Graphene ◽  
Mechanical And Thermal Properties ◽  
Epoxy Nanocomposites ◽  
Single Walled Carbon Nanotube ◽  
Single Walled Carbon ◽  
Layer Graphene

Preparation and Characterization of Micro-Graphite Filled Poly(Lactic Acid) Composites: Part 1 - Rheological and Thermal Properties

2020 ◽  
Vol 981 ◽  
pp. 138-143
Author(s):  
Esa N. Shohih ◽  
Mujtahid Kaavessina ◽  
Henry A. S. Lomi ◽  
Betha P. Pratiwi ◽  
Sperisa Distantina ◽  
...  
Keyword(s):  
Electrical Conductivity ◽  
Lactic Acid ◽  
Thermal Properties ◽  
Conductive Polymer ◽  
Complex Viscosity ◽  
Poly Lactic Acid ◽  
Homogeneous Distribution ◽  
Mechanical And Thermal Properties ◽  
Blending Method ◽  
Stirring Time

Conductive polymer composites (CPCs) have attracted great attention of researchers due to their enhanced properties such as an adjustable electrical conductivity, good processability, good mechanical and thermal properties, etc. CPCs had many potencies for wider application in electronic devices. Poly (lactic acid) or PLA is one of the interesting polymers used in the developing of these new important materials. PLA properties are comparable to the synthetic petroleum-based polymers such as polyethylene terephthalate (PET), polypropylene (PP), etc. This research focuses on studying the rheological and thermal properties of PLA/micro-graphite as a conductive polymer composite which adjustable its electrical conductivity. In this study, the PLA/micro-graphite was prepared through solvent blending method using chloroform. The micro-graphite composition was varied from 0%, 5%, and 10 % (w/w) with different stirring time (30 and 60 minutes) and then, poured in glass mould. In the melt rheology study, the frequency sweep test showed that the complex viscosity (|η*|) of the bio-composite increased with the micro-graphite loading. The same tendency was also found in thermal property and stability. The melting temperature and thermal degradation were slightly increasing. The crystallinity of PLA was influenced by the presence of micro-graphite. In this solvent blending method, the homogeneous distribution of micro-graphite in the bio-composite required at least 60 minutes (stirred at 650 rpm and 60 °C).

Sign in / Sign up

Export Citation Format

Share Document