Lightweight Nanofibrous Crosslinked Composite Aerogels with Controllable Shapes and Superelasticity for Pressure Sensors

2022 ◽  
pp. 2100834
Author(s):  
Zhaofeng Ouyang ◽  
Chuang Wang ◽  
Dewen Xu ◽  
Hou‐Yong Yu ◽  
Ying Zhou ◽  
...  
Keyword(s):  
Pressure Sensors ◽  
Composite Aerogels

scholarly journals Ultra-Sensitive Piezo-Resistive Sensors Constructed with Reduced Graphene Oxide/Polyolefin Elastomer (RGO/POE) Nanofiber Aerogels

Polymers ◽  
2019 ◽  
Vol 11 (11) ◽  
pp. 1883 ◽  
Author(s):  
Weibing Zhong ◽  
Haiqing Jiang ◽  
Liyan Yang ◽  
Ashish Yadav ◽  
Xincheng Ding ◽  
...  
Keyword(s):  
Graphene Oxide ◽  
Three Dimensional ◽  
Pressure Sensors ◽  
High Sensitivity ◽  
Working Pressure ◽  
Nanofiber Composite ◽  
Composite Aerogel ◽  
Polyolefin Elastomer ◽  
Reduced Graphene ◽  
Composite Aerogels

Flexible wearable pressure sensors have received extensive attention in recent years because of the promising application potentials in health management, humanoid robots, and human machine interfaces. Among the many sensory performances, the high sensitivity is an essential requirement for the practical use of flexible sensors. Therefore, numerous research studies are devoted to improving the sensitivity of the flexible pressure sensors. The fiber assemblies are recognized as an ideal substrate for a highly sensitive piezoresistive sensor because its three-dimensional porous structure can be easily compressed and can provide high interconnection possibilities of the conductive component. Moreover, it is expected to achieve high sensitivity by raising the porosity of the fiber assemblies. In this paper, the three-dimensional reduced graphene oxide/polyolefin elastomer (RGO/POE) nanofiber composite aerogels were prepared by chemical reducing the graphene oxide (GO)/POE nanofiber composite aerogels, which were obtained by freeze drying the mixture of the GO aqueous solution and the POE nanofiber suspension. It was found that the volumetric shrinkage of thermoplastic POE nanofibers during the reduction process enhanced the compression mechanical strength of the composite aerogel, while decreasing its sensitivity. Therefore, the composite aerogels with varying POE nanofiber usage were prepared to balance the sensitivity and working pressure range. The results indicated that the composite aerogel with POE nanofiber/RGO proportion of 3:3 was the optimal sample, which exhibits high sensitivity (ca. 223 kPa−1) and working pressure ranging from 0 to 17.7 kPa. In addition, the composite aerogel showed strong stability when it is either compressed with different frequencies or reversibly compressed and released 5000 times.

PROPAGATION OF THE BURNING WAVE IN A PULSED DETONATION COMBUSTOR OPERATING ON MIXTURES OF HEPTANE AND JET A-1 WITH AIR AND OXYGEN AT [O2/AIR] < 1

2020 ◽  
Author(s):  
M. S. ASSAD ◽  
◽  
O. G. PENYAZKOV ◽  
I. I. CHERNUHO ◽  
K. ALHUSSAN ◽  
...  
Keyword(s):  
Wave Propagation ◽  
Combustion Wave ◽  
Equivalence Ratio ◽  
Pressure Sensors ◽  
Jet Fuel ◽  
Propagation Time ◽  
Burning Wave ◽  
Pulsed Detonation ◽  
Combustion Wave Propagation ◽  
Fuel Jet

This work is devoted to the study of the dynamics of combustion wave propagation in oxygen-enriched mixtures of n-heptane with air and jet fuel "Jet A-1" in a small-size pulsed detonation combustor (PDC) with a diameter of 20 mm and a length less than 1 m. Experiments are carried out after the PDC reaches a stationary thermal regime when changing the equivalence ratio (ϕ = 0.73-1.89) and the oxygen-to-air ratio ([O2/air] = 0.15-0.60). The velocity of the combustion wave is determined by measuring the propagation time of the flame front between adjacent pressure sensors that form measurement segements along the PDC.

Development of circuit solution and design of capacitive pressure sensor array for applied robotics

2020 ◽  
Vol 8 (4) ◽  
pp. 296-307
Author(s):  
Konstantin Krestovnikov ◽  
Aleksei Erashov ◽  
Аleksandr Bykov
Keyword(s):  
Pressure Sensor ◽  
Output Signal ◽  
Sensor Array ◽  
Applied Pressure ◽  
Pressure Sensors ◽  
Fine Tuning ◽  
Capacitive Pressure Sensor ◽  
Cell Parameters ◽  
Linear Pattern ◽  
Sensor Structure

This paper presents development of pressure sensor array with capacitance-type unit sensors, with scalable number of cells. Different assemblies of unit pressure sensors and their arrays were considered, their characteristics and fabrication methods were investigated. The structure of primary pressure transducer (PPT) array was presented; its operating principle of array was illustrated, calculated reference ratios were derived. The interface circuit, allowing to transform the changes in the primary transducer capacitance into voltage level variations, was proposed. A prototype sensor was implemented; the dependency of output signal power from the applied force was empirically obtained. In the range under 30 N it exhibited a linear pattern. The sensitivity of the array cells to the applied pressure is in the range 134.56..160.35. The measured drift of the output signals from the array cells after 10,000 loading cycles was 1.39%. For developed prototype of the pressure sensor array, based on the experimental data, the average signal-to-noise ratio over the cells was calculated, and equaled 63.47 dB. The proposed prototype was fabricated of easily available materials. It is relatively inexpensive and requires no fine-tuning of each individual cell. Capacitance-type operation type, compared to piezoresistive one, ensures greater stability of the output signal. The scalability and adjustability of cell parameters are achieved with layered sensor structure. The pressure sensor array, presented in this paper, can be utilized in various robotic systems.

Effects of Heat Treatment Temperature on Photocatalytic Activity of TiO2/SiO2 Composite Aerogels

2013 ◽  
Vol 27 (10) ◽  
pp. 1079-1083
Author(s):  
Zhao-Hui LIU ◽  
Gen-Liang HOU ◽  
Xun-Jia SU ◽  
Feng GUO ◽  
Zhou XIAO ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Photocatalytic Activity ◽  
Heat Treatment Temperature ◽  
Treatment Temperature ◽  
Composite Aerogels
Sign in / Sign up

Export Citation Format

Share Document