Influence of Hardening Relations on Forming Limit Curves Predicted by the Theory of Marciniak, Kuczyński, and Pokora

2009 ◽  
pp. 43-65 ◽  
Author(s):  
Heinrich Werner
Keyword(s):  
Forming Limit ◽  
Forming Limit Curves

Effect of the Constitutive Law on the Accuracy of Prediction of the Forming Limit Curves

2012 ◽  
Vol 504-506 ◽  
pp. 77-82 ◽  
Author(s):  
Liana Paraianu ◽  
Dan Sorin Comsa ◽  
Ioan Pavel Nicodim ◽  
Ioan Ciobanu ◽  
Dorel Banabic
Keyword(s):  
Sheet Metal ◽  
Mechanical Response ◽  
Yield Criterion ◽  
Plastic Anisotropy ◽  
Equivalent Stress ◽  
Point Of View ◽  
Constitutive Law ◽  
Forming Limit ◽  
Accuracy Of Prediction ◽  
Forming Limit Curves

The accuracy of the forming limit curves predicted by the Marciniak-Kuczynski model depends on the type and flexibility of the constitutive equations used to describe the mechanical response of the sheet metal. From this point of view, the yield criterion has the most significant influence. The paper presents a comparative analysis referring to the quality of the forming limit curves predicted by the Marciniak-Kuczynski model for the case when the plastic anisotropy of a DC04 sheet metal is described by the BBC2005 yield criterion. The coefficients included in the expression of the BBC2005 equivalent stress are evaluated using different identification strategies (with 4, 6, 7, and 8 mechanical parameters). The forming limit curves predicted by the Marciniak-Kuczynski model in each of the cases previously mentioned are compared with experimental data.

Forming Limits Under Stretch-Bending Through Distortionless and Distortional Anisotropic Hardening

2018 ◽  
Vol 140 (12) ◽  
Author(s):  
Ji He ◽  
Bin Gu ◽  
Yongfeng Li ◽  
Shuhui Li
Keyword(s):  
Detailed Comparison ◽  
Forming Limit ◽  
Anisotropic Hardening ◽  
Hardening Model ◽  
Stretch Bending ◽  
Bending Process ◽  
Hardening Models ◽  
Out Of Plane ◽  
Forming Limit Curves ◽  
Insight Into

The necking behavior of sheet metals under stretch-bending process is a challenge for the forming limit prediction. State-of-the-art forming limit curves (FLCs) allow the prediction under the in-plane stretching but fall short in the case under out-of-plane loading condition. To account for the bending and straightening deformation when sheet metal enters a die cavity or slide along a radius, anisotropic hardening model is essential to reflect the nonproportional loading effect on stress evolution. This paper aims to revisit the M-K analysis under the stretch-bending condition and extend it to accommodate both distortionless and distortional anisotropic hardening behavior. Furthermore, hardening models are calibrated based on the same material response. Then the detailed comparison is proposed for providing better insight into the numerical prediction and necking behavior. Finally, the evolution of the yield surface and stress transition states is examined. It is found that the forming limit prediction under stretch-bending condition through the M-K analysis strongly depends on the employed anisotropic hardening model.

Orientation and Path Dependence of Formability in the Stress- and the Extended Stress-Based Forming Limit Curves

2008 ◽  
Vol 130 (4) ◽  
Author(s):  
C. Hari Manoj Simha ◽  
Kaan Inal ◽  
Michael J. Worswick
Keyword(s):  
Strain Path ◽  
Path Dependence ◽  
Forming Limit ◽  
Stress Space ◽  
Forming Limit Diagrams ◽  
Metall Trans ◽  
Strain Paths ◽  
Strain Path Changes ◽  
Path Dependent ◽  
Forming Limit Curves

This article analyzes the formability data sets for aluminum killed steel (Laukonis, J. V., and Ghosh, A. K., 1978, “Effects of Strain Path Changes on the Formability of Sheet Metals,” Metall. Trans. A., 9, pp. 1849–1856), for Al 2008-T4 (Graf, A., and Hosford, W., 1993, “Effect of Changing Strain Paths on Forming Limit Diagrams of Al 2008-T4,” Metall. Trans. A, 24A, pp. 2503–2512) and for Al 6111-T4 (Graf, A., and Hosford, W., 1994, “The Influence of Strain-Path Changes on Forming Limit Diagrams of Al 6111 T4,” Int. J. Mech. Sci., 36, pp. 897–910). These articles present strain-based forming limit curves (ϵFLCs) for both as-received and prestrained sheets. Using phenomenological yield functions, and assuming isotropic hardening, the ϵFLCs are transformed into principal stress space to obtain stress-based forming limit curves (σFLCs) and the principal stresses are transformed into effective stress and mean stress space to obtain the extended stress-based forming limit curves (XSFLCs). A definition of path dependence for the σFLC and XSFLC is proposed and used to classify the obtained limit curves as path dependent or independent. The path dependence of forming limit stresses is observed for some of the prestrain paths. Based on the results, a novel criterion that, with a knowledge of the forming limit stresses of the as-received material, can be used to predict whether the limit stresses are path dependent or independent for a given prestrain path is proposed. The results also suggest that kinematic hardening and transient hardening effects may explain the path dependence observed in some of the prestrain paths.

A method to develop multistage forming limit curves for copper alloy strip

1984 ◽  
Vol 3 (2) ◽  
pp. 157-164 ◽  
Author(s):  
F. Mandigo ◽  
E. Shapiro
Keyword(s):  
Copper Alloy ◽  
Forming Limit ◽  
Alloy Strip ◽  
Forming Limit Curves
Sign in / Sign up

Export Citation Format

Share Document