Modelling of hard turning: effect of tool geometry on cutting force

2010 ◽  
pp. 227-230
Author(s):  
Z. Y. Shi ◽  
Z. Q. Liu ◽  
C. M. Cao
Keyword(s):  
Cutting Force ◽  
Hard Turning ◽  
Tool Geometry

Surface Roughness and Cutting Force Components Evaluation in Hard Turning by Differently Shaped Cutting Tools

2016 ◽  
Vol 862 ◽  
pp. 26-32 ◽  
Author(s):  
Michaela Samardžiová
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Hard Turning ◽  
Cutting Tool ◽  
Single Point ◽  
Machining Process ◽  
Tool Geometry ◽  
Machined Surface ◽  
Cutting Force Components ◽  
Force Components

There is a difference in machining by the cutting tool with defined geometry and undefined geometry. That is one of the reasons of implementation of hard turning into the machining process. In current manufacturing processes is hard turning many times used as a fine finish operation. It has many advantages – machining by single point cutting tool, high productivity, flexibility, ability to produce parts with complex shapes at one clamping. Very important is to solve machined surface quality. There is a possibility to use wiper geometry in hard turning process to achieve 3 – 4 times lower surface roughness values. Cutting parameters influence cutting process as well as cutting tool geometry. It is necessary to take into consideration cutting force components as well. Issue of the use of wiper geometry has been still insufficiently researched.

Study on cutting force and surface micro-topography of hard turning of GCr15 steel

2014 ◽  
Vol 72 (9-12) ◽  
pp. 1639-1645 ◽  
Author(s):  
Tao Chen ◽  
Suyan Li ◽  
Bangxin Han ◽  
Guangjun Liu
Keyword(s):  
Cutting Force ◽  
Hard Turning ◽  
Gcr15 Steel ◽  
Micro Topography

scholarly journals Machining force comparison for surface defect hard turning and conventional hard turning of AISI 52100 steel

2021 ◽  
Vol 13 (3) ◽  
pp. 205-214
Author(s):  
P. U MAMAHESWARRAO ◽  
D. RANGARAJU ◽  
K. N. S. SUMAN ◽  
B. RAVISANKAR
Keyword(s):  
Hard Turning ◽  
Surface Defect ◽  
Cutting Speed ◽  
Tool Geometry ◽  
Depth Of Cut ◽  
Nose Radius ◽  
Aisi 52100 ◽  
Machining Force ◽  
Aisi 52100 Steel ◽  
The Impact

In this article, a recently developed method called surface defect machining (SDM) for hard turning has been adopted and termed surface defect hard turning (SDHT). The main purpose of the present study was to explore the impact of cutting parameters like cutting speed, feed, depth of cut, and tool geometry parameters such as nose radius and negative rake angle of the machining force during surface defect hard turning (SDHT) of AISI 52100 steel in dry condition with Polycrystalline cubic boron nitride (PCBN) tool; and results were compared with conventional hard turning (CHT). Experimentation is devised and executed as per Central Composite Design (CCD) of Response Surface Methodology (RSM). Results reported that an average machining force was decreased by 22% for surface defect hard turning (SDHT) compared to conventional hard turning (CHT).

Statistical Cutting Force Model for Orthogonal Cutting of Polytetrafluoroethylene (PTFE) Composites

2013 ◽  
Author(s):  
Felicia Stan ◽  
Daniel Vlad ◽  
Catalin Fetecau
Keyword(s):  
Friction Coefficient ◽  
Cutting Force ◽  
Feed Rate ◽  
Normal Force ◽  
Polynomial Regression ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Tool Geometry ◽  
Force Model

This paper presents an experimental investigation of the cutting forces response during the orthogonal cutting of polytetrafluoroethylene (PTFE) and PTFE-based composites using the Taguchi method. Cutting experiments were conducted using the L27 orthogonal array and the effects of the cutting parameters (feed rate, cutting speed and rake angle) on the cutting force were analyzed using the S/N ratio response and the analysis of variance (ANOVA). Statistical models that correlate the cutting force with process variables were developed using ANOVA and polynomial regression. The variation of the apparent friction coefficient was analyzed with respect to tool geometry and the cutting process. The results indicated that cutting and thrust forces increase with increasing feed rate, and decrease with increasing rake angles from negative to positive values and increasing cutting speed. A power law relationship between the apparent friction coefficient and the normal force exerted by the chip on the tool-rake face was identified, the former decreasing with an increasing normal force.

Comparative assessment between AlTiN and AlTiSiN coated carbide tools towards machinability improvement of AISI D6 steel in dry hard turning

2021 ◽  
pp. 095440622110373
Author(s):  
Anshuman Das ◽  
Miyaz Kamal ◽  
Sudhansu Ranjan Das ◽  
Saroj Kumar Patel ◽  
Asutosh Panda ◽  
...  
Keyword(s):  
Cutting Force ◽  
Tool Life ◽  
Hard Turning ◽  
Flank Wear ◽  
Chip Morphology ◽  
Comparative Assessment ◽  
Carbide Tool ◽  
Crater Wear ◽  
Coated Carbide ◽  
Coated Carbide Tools

AISI D6 (hardness 65 HRC) is one of the hard-to-cut steel alloys and commonly used in mould and die making industries. In general, CBN and PCBN tools are used for machining hardened steel but its higher cost makes the use for limited applications. However, the usefulness of carbide tool with selective coatings is the best substitute having comparable tool life, and in terms of cost is approximately one-tenth of CBN tool. The present study highlights a detailed analysis on machinability investigation of hardened AISI D6 alloy die steel using newly developed SPPP-AlTiSiN coated carbide tools in finish dry turning operation. In addition, a comparative assessment has been performed based on the effectiveness of cutting tool performance of nanocomposite coating of AlTiN deposited by hyperlox PVD technique and a coating of AlTiSiN deposited by scalable pulsed power plasma (SPPP) technique. The required number of machining trials under varied cutting conditions (speed, depth of cut, feed) were based on L16 orthogonal array design which investigated the crater wear, flank wear, surface roughness, chip morphology, and cutting force in hard turning. Out of the two cutting tools, newly-developed nanocomposite (SPPP-AlTiSiN) coated carbide tool promises an improved surface finish, minimum cutting force, longer tool life due to lower value of crater & flank wears, and considerable improvement in tool life (i.e., by 47.83%). At higher cutting speeds, the crater wear length and flank wear increases whereas the surface roughness, crater wear width and cutting force decreases. Chip morphology confirmed the formation of serrated type saw tooth chips.

Sign in / Sign up

Export Citation Format

Share Document