Correlation of Hydraulic and Pneumatic Tightness for Brake Fluid Reservoir Non Return Valve

Author(s):  
Maciej Wnuk ◽  
Artur Iluk
2020 ◽  
Vol 92 (1) ◽  
pp. 10906
Author(s):  
Jeroen Schoenmaker ◽  
Pâmella Gonçalves Martins ◽  
Guilherme Corsi Miranda da Silva ◽  
Julio Carlos Teixeira

Organic Rankine Cycle (ORC) systems are increasingly gaining relevance in the renewable and sustainable energy scenario. Recently our research group published a manuscript identifying a new type of thermodynamic cycle entitled Buoyancy Organic Rankine Cycle (BORC) [J. Schoenmaker, J.F.Q. Rey, K.R. Pirota, Renew. Energy 36, 999 (2011)]. In this work we present two main contributions. First, we propose a refined thermodynamic model for BORC systems accounting for the specific heat of the working fluid. Considering the refined model, the efficiencies for Pentane and Dichloromethane at temperatures up to 100 °C were estimated to be 17.2%. Second, we show a proof of concept BORC system using a 3 m tall, 0.062 m diameter polycarbonate tube as a column-fluid reservoir. We used water as a column fluid. The thermal stability and uniformity throughout the tube has been carefully simulated and verified experimentally. After the thermal parameters of the water column have been fully characterized, we developed a test body to allow an adequate assessment of the BORC-system's efficiency. We obtained 0.84% efficiency for 43.8 °C working temperature. This corresponds to 35% of the Carnot efficiency calculated for the same temperature difference. Limitations of the model and the apparatus are put into perspective, pointing directions for further developments of BORC systems.


Author(s):  
Olawale O Ajibola ◽  
Ojo J Akinribide ◽  
Samuel O Akinwamide ◽  
Peter A Olubambi

1998 ◽  
Author(s):  
John E. Hunter ◽  
Scott S. Cartier ◽  
David J. Temple ◽  
Robert C. Mason

2015 ◽  
Vol 2015 ◽  
pp. 1-10 ◽  
Author(s):  
Olawale Olarewaju Ajibola ◽  
Daniel Toyin Oloruntoba

The effects of wear and corrosion of cast AA6061 aluminium alloy were studied with and without brake fluid using a wear jig while the corrosion rate was determined in brake fluid for 70 days under two experimental set-ups. The tests, yielded 0.00000123 g/mm2/min highest wear rate at 147000 wear cycles and 0.0334 mg/mm2/yr as the highest corrosion rate within the early 39th day of immersion in oil, the values being considered comparatively lower than those obtained for Al alloy in most common wet abrasion test and corrosion in aqueous solutions as previously reported in literature. The material loss rates to wear and corrosion were determined from the equations relating to wear and corrosion based on the ASTM designations. The results show that the combined actions of wear and corrosion contribute to the total loss of piston material immersed in brake oil. This is greater than either of their effects individually on cast Al alloy in the brake oil.


1991 ◽  
Vol 163 (1) ◽  
pp. 197-200 ◽  
Author(s):  
B. E. Hirsch ◽  
M. Amodio ◽  
A. I. Einzig ◽  
R. Halevy ◽  
R. Soeiro

2018 ◽  
Vol 7 (2.14) ◽  
pp. 512 ◽  
Author(s):  
Olawale Ajibola ◽  
Oladeji Ige ◽  
Peter Olubambi

The twofold impact of wear and corrosion on wrought A6061 alloy in hydraulic DOT3 brake fluid environment was studied. The wear studies were performed on the samples using a developed wear-jig. Weight loss corrosion test method was used to determine the corrosion rate of the wrought A6061 alloy samples immersed in the brake fluid for a total of 1680 hours. From the results of wear tests carried out on the A6061 alloy sample with brake oil, the highest wear value of 5.24x10-7 mg/mm2/cycle (approx.) was obtained from 6 N (approx) force after 130 minutes. The wrought A6061 alloy material demonstrated the highest corrosion rates nearly 3.0 x10-2 mg/mm2/yr within the early 168 hours of immersion in brake fluid. The result is practically lower than the corrosion rate of cast specimen in DOT3 brake oil or some other alloys immersed in other corrosive media that were previously reported in the literature. The results show that small amount of chemical corrosion is sufficient to cause and accelerate mechanical wear of the material in usage.


Sign in / Sign up

Export Citation Format

Share Document