scholarly journals In-Situ Tensile Test on 316H Sent Using Digital Image Correlation

2016 ◽  
pp. 45-52
Author(s):  
L. Podesta ◽  
B. Wattrisse ◽  
F. Latourte ◽  
L. Waltz ◽  
J.-M. Muracciole
Keyword(s):  
Digital Image Correlation ◽  
Tensile Test ◽  
Digital Image ◽  
Image Correlation

scholarly journals Digital Image Correlation for Evaluation of Cracks in Reinforced Concrete Bridge Slabs

2021 ◽  
Vol 6 (7) ◽  
pp. 99
Author(s):  
Christian Overgaard Christensen ◽  
Jacob Wittrup Schmidt ◽  
Philip Skov Halding ◽  
Medha Kapoor ◽  
Per Goltermann
Keyword(s):  
Reinforced Concrete ◽  
Digital Image Correlation ◽  
Crack Initiation ◽  
Laboratory Test ◽  
Digital Image ◽  
Crack Detection ◽  
Image Correlation ◽  
In Situ Tests ◽  
Stop Criterion

In proof-loading of concrete slab bridges, advanced monitoring methods are required for identification of stop criteria. In this study, Two-Dimensional Digital Image Correlation (2D DIC) is investigated as one of the governing measurement methods for crack detection and evaluation. The investigations are deemed to provide valuable information about DIC capabilities under different environmental conditions and to evaluate the capabilities in relation to stop criterion verifications. Three Overturned T-beam (OT) Reinforced Concrete (RC) slabs are used for the assessment. Of these, two are in situ strips (0.55 × 3.6 × 9.0 m) cut from a full-scale OT-slab bridge with a span of 9 m and one is a downscaled slab tested under laboratory conditions (0.37 × 1.7 × 8.4 m). The 2D DIC results includes full-field plots, investigation of the time of crack detection and monitoring of crack widths. Grey-level transformation was used for the in situ tests to ensure sufficient readability and results comparable to the laboratory test. Crack initiation for the laboratory test (with speckle pattern) and in situ tests (plain concrete surface) were detected at intervals of approximately 0.1 mm to 0.3 mm and 0.2 mm to 0.3 mm, respectively. Consequently, the paper evaluates a more qualitative approach to DIC test results, where crack indications and crack detection can be used as a stop criterion. It was furthermore identified that crack initiation was reached at high load levels, implying the importance of a target load.

Methodology for in situ stress intensity factor determination on cracked structures by digital image correlation

2010 ◽  
Vol 1 (4) ◽  
pp. 344-357 ◽  
Author(s):  
V. Richter‐Trummer ◽  
P.M.G.P. Moreira ◽  
S.D. Pastrama ◽  
M.A.P. Vaz ◽  
P.M.S.T. de Castro
Keyword(s):  
Stress Intensity Factor ◽  
Stress Intensity ◽  
Digital Image Correlation ◽  
Intensity Factor ◽  
Digital Image ◽  
Strain Field ◽  
Image Correlation ◽  
Content Type ◽  
Cracked Structures

PurposeThe purpose of this paper is to develop a methodology for in situ stress intensity factor (SIF) determination that can be used for the analysis of cracked structures. The technique is based on digital image correlation (DIC) combined with an overdetermined algorithm.Design/methodology/approachThe linear overdeterministic algorithm for calculating the SIF based on stress values around the crack tip is applied to a strain field obtained by DIC.FindingsAs long as the image quality is sufficiently high, a good accuracy can be obtained for the measured SIF. The crack tip can be automatically detected based on the same strain field. The use of the strain field instead of the displacement field, eliminates problems related to the rigid body motion of the analysed structure.Practical implicationsIn future works, based on the applied techniques, the SIF of complex cracked plane stress structures can be accurately determined in real engineering applications.Originality/valueThe paper demonstrates application of known techniques, refined for other applications, also the use of stress field for SIF overdeterministic calculations.

scholarly journals Multi-Scale Digital Image Correlation Analysis of In Situ Deformation of Open-Cell UHMWPE Foam

2020 ◽  
Author(s):  
Eugene S. Statnik ◽  
Codrutza Dragu ◽  
Cyril Besnard ◽  
Alexander J.G. Lunt ◽  
Alexey I. Salimon ◽  
...  
Keyword(s):  
Digital Image Correlation ◽  
Digital Image ◽  
High Performance ◽  
Structural Evolution ◽  
Image Correlation ◽  
Deformation Bands ◽  
Open Cell ◽  
Polyether Ether Ketone ◽  
Structural Levels

Porous ultra-high molecular weight polyethylene (UHMWPE) is a high performance bioinert polymer used in cranio-facial reconstructive surgery in procedures where relatively low mechanical stresses arise. As an alternative to much stiffer and costly polyether-ether-ketone (PEEK) polymer, UHMWPE finds further wide application in hierarchically structured hybrids for advanced implants mimicking cartilage, cortical and trabecular bone tissues within a single component. The mechanical behaviour of open-cell UHMWPE sponges obtained through sacrificial desalination of hot compression-moulded UHMWPE-NaCl powder mixtures shows a complex dependence on the fabrication parameters and microstructural features. In particular, similarly to other porous media it displays significant inhomogeneity of strain that readily localises within deformation bands that govern the overall response. In this article, we report advances in the development of accurate experimental techniques for operando studies of the structure-performance relationship applied to the porous UHMWPE medium with pore sizes of about 250 µm that are most well-suited for live cell proliferation and fast vascularization of implants. Samples of UHMWPE sponges were subjected to in situ compression using a micromechanical testing device within Scanning Electron Microscope (SEM) chamber, allowing the acquisition of high-resolution image sequences for Digital Image Correlation (DIC) analysis. Special masking and image processing algorithms were developed and applied to reveal the evolution of pore size and aspect ratio. Key structural evolution and deformation localisation phenomena were identified at both macro- and micro-structural levels in the elastic and plastic regimes. The motion of pore walls was quantitatively described, and the presence and influence of strain localisation zones were revealed and analysed using DIC technique.

Simulation of the Global Response of Welded Joint Using Digital Image Correlation Measurement

2013 ◽  
Vol 749 ◽  
pp. 597-600
Author(s):  
Chao He ◽  
Shi Ming Cui ◽  
Yan Zeng Wu ◽  
Ze Fu Luo ◽  
Qing Yuan Wang
Keyword(s):  
Digital Image Correlation ◽  
Tensile Test ◽  
Tensile Properties ◽  
Digital Image ◽  
Welded Joint ◽  
Pure Aluminum ◽  
Local Stress ◽  
Image Correlation ◽  
Global Response ◽  
Mechanical Heterogeneity

The effect of the mechanical heterogeneity on the global and local tensile properties of laser-arc hybrid welded joints in industrial pure aluminum has been investigated. Digital image correlation method has been used during tensile test for mapping the strain distribution and to determine the local stress-strain curves of FZ and HAZ. The tensile properties of the various regions are very heterogeneous and HAZ is the weakest region because of the strain localizes during tensile test. Finite element technique was used to model the global response of welded joint based on local constitutive properties which could be determined from DIC results.

Sign in / Sign up

Export Citation Format

Share Document