Free and Restrained Shrinkage of Hybrid Steel Fibres Reinforced Concrete

2017 ◽  
pp. 339-346
Author(s):  
Zahran Al-Kamyani ◽  
Kypros Pilakoutas ◽  
Maurizio Guadagnini ◽  
Panos Papastergiou
Keyword(s):  
Reinforced Concrete ◽  
Restrained Shrinkage ◽  
Steel Fibres

Impact of shrinkage on crack width and deflections of reinforced concrete beams with and without steel fibres

2019 ◽  
Vol 181 ◽  
pp. 387-396 ◽  
Author(s):  
Zahran Al-Kamyani ◽  
Maurizio Guadagnini ◽  
Kypros Pilakoutas
Keyword(s):  
Reinforced Concrete ◽  
Crack Width ◽  
Concrete Beams ◽  
Reinforced Concrete Beams ◽  
Steel Fibres

scholarly journals Experimental Investigation of Shear Strength for Steel Fibre Reinforced Concrete Beams

2021 ◽  
Vol 15 (1) ◽  
pp. 81-92
Author(s):  
Constantinos B. Demakos ◽  
Constantinos C. Repapis ◽  
Dimitros P. Drivas
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Shear Strength ◽  
Reinforced Concrete ◽  
Steel Fibre ◽  
Concrete Beams ◽  
Reinforced Concrete Beams ◽  
Fibre Reinforced Concrete ◽  
Steel Fibres ◽  
Steel Fibre Reinforced Concrete

Aims: The aim of this paper is to investigate the influence of the volume fraction of fibres, the depth of the beam and the shear span-to-depth ratio on the shear strength of steel fibre reinforced concrete beams. Background: Concrete is a material widely used in structures, as it has high compressive strength and stiffness with low cost manufacturing. However, it presents low tensile strength and ductility. Therefore, through years various materials have been embedded inside it to improve its properties, one of which is steel fibres. Steel fibre reinforced concrete presents improved flexural, tensile, shear and torsional strength and post-cracking ductility. Objective: A better understanding of the shear performance of SFRC could lead to improved behaviour and higher safety of structures subject to high shear forces. Therefore, the influence of steel fibres on shear strength of reinforced concrete beams without transverse reinforcement is experimentally investigated. Methods: Eighteen concrete beams were constructed for this purpose and tested under monotonic four-point bending, six of which were made of plain concrete and twelve of SFRC. Two different aspect ratios of beams, steel fibres volume fractions and shear span-to-depth ratios were selected. Results: During the experimental tests, the ultimate loading, deformation at the mid-span, propagation of cracks and failure mode were detected. From the tests, it was shown that SFRC beams with high volume fractions of fibres exhibited an increased shear capacity. Conclusion: The addition of steel fibres resulted in a slight increase of the compressive strength and a significant increase in the tensile strength of concrete and shear resistance capacity of the beam. Moreover, these beams exhibit a more ductile behaviour. Empirical relations predicting the shear strength capacity of fibre reinforced concrete beams were revised and applied successfully to verify the experimental results obtained in this study.

scholarly journals Numerical Simulation of the Fracture Behaviour of High-Performance Fibre Reinforced Concrete by Using a Cohesive-Crack-Based Inverse Analysis

2021 ◽  
Author(s):  
Alejandro Enfedaque ◽  
Marcos G. Alberti ◽  
Jaime C. Gálvez ◽  
Pedro Cabanas
Keyword(s):  
Mechanical Properties ◽  
Reinforced Concrete ◽  
Inverse Analysis ◽  
High Performance ◽  
Fracture Behaviour ◽  
Constitutive Models ◽  
Cohesive Crack ◽  
Fibre Reinforced Concrete ◽  
Steel Fibres ◽  
Structural Applications

Fibre reinforced concrete (FRC) has become an alternative for structural applications due its outstanding mechanical properties. The appearance of new types of fibres and the fibre cocktails that can be configured mixing them has created FRC that clearly exceed the minimum mechanical properties required in the standards. Consequently, in order to take full advantage of the contribution of the fibres in construction projects, it is of great interest to have constitutive models that simulate the behaviour of the materials. This study aimed to simulate the fracture behaviour of five types of FRC, three with steel hooked fibres, one with a combination of two types of steel fibres and one with a combination of polyolefin fibres and two types of steel fibres, by means of an inverse analysis based on the cohesive crack approach. The results of the numerical simulations defined the softening functions of each FRC formulation and have pointed out the synergies that are created through use of fibre cocktails. The information obtained might suppose a remarkable advance for designers using high-performance FRC in structural elements.

scholarly journals Failure mode in shear of steel fiber reinforced concrete beams

2018 ◽  
Vol 163 ◽  
pp. 02003 ◽  
Author(s):  
Julita Krassowska ◽  
Marta Kosior-Kazberuk
Keyword(s):  
Reinforced Concrete ◽  
Steel Fiber ◽  
Concrete Beams ◽  
Fiber Reinforced Concrete ◽  
Reinforced Concrete Beams ◽  
Bending Test ◽  
Fibre Reinforced Concrete ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Steel Fibres

Experimental tests were carried out to assess the failure model of steel fiber reinforced concrete beams. Experimental research was focused on observing changes in the behavior of the tested elements depending on the amount of shear reinforcement and the fiber. Model two-span beams with a cross-section of 80x180 mm and a length of 2000 mm were tested. The beams had varied stirrup spacing. The following amounts of steel fibres in concrete were used: 78.5 kg/m3 (1.0%) i 118 kg/m3 (1.5%). Concrete beams without fibres were examined at the same time. The beams were loaded in a five-point bending test until they were destroyed. Shear or bending capacity of the element was observed. Fibre reinforced concrete beams were not destroyed rapidly, but they kept their shape consistent under load. Larger number of diagonal cracks with a smaller width were observed in fibre reinforced concrete beams. Failure of concrete beams without fibres was rapid, with a characteristic brittle cracking. Steel fibres revealed the ability to transfer significant shear stress after cracking in comparison to plain concrete.

Les bétons renforcés de fibres d'acier et la multifissuration

2000 ◽  
Vol 27 (4) ◽  
pp. 774-784 ◽  
Author(s):  
Benoît Bissonnette ◽  
Yves Therrien ◽  
Richard Pleau ◽  
Michel Pigeon ◽  
François Saucier
Keyword(s):  
Reinforced Concrete ◽  
Large Scale ◽  
Intrinsic Property ◽  
Tensile Tests ◽  
Experimental Program ◽  
Fibre Reinforcement ◽  
Fibre Reinforced Concrete ◽  
Restrained Shrinkage ◽  
Test Results ◽  
Multiple Cracking

This paper presents the results of an investigation aimed at establishing if multiple cracking can be an intrinsic property of steel fibre reinforced concrete (SFRC) in the hardened state and identifying the conditions to obtain it systematically. For this purpose, uniaxial restrained shrinkage tests and tensile tests were performed on large-scale SFRC specimens. The parameters studied in the experimental program were the fibre content (0-100 kg/m3), the fibre geometry, and the water to cement ratio of the concrete matrix (w/c = 0.40-0.80). The test results tend to indicate that multiple cracking is not a property of SFRC as such, at least within the range of concrete matrices and fibre contents investigated and that were intended to be compatible with practical considerations. While it does not mean that fibre reinforcement is not effective in terms of crack control, it is important to be careful in the analysis of test results where the effect of the restraining and exposure conditions might have been significant.Key words: cracking, drying shrinkage, fibre-reinforced concrete, multiple cracking, repairs, restrained shrinkage, steel fibres, tension.

Sign in / Sign up

Export Citation Format

Share Document