scholarly journals Assessing the moisture susceptibility of aggregates with Los Angeles abrasion test

2017 ◽  
Author(s):  
Adelia Dwidarma Nataadmadja ◽  
Oki Setyandito ◽  
Eduardi Prahara ◽  
Ida Riyanti
Keyword(s):  
Los Angeles ◽  
Moisture Susceptibility ◽  
Abrasion Test ◽  
Los Angeles Abrasion

NOISE LEVEL MEASUREMENT TEST TO PREDICT THE ABRASION RESISTANCE OF ROCK AGGREGATES

2013 ◽  
Vol 12 (04) ◽  
pp. 1350021 ◽  
Author(s):  
S. KAHRAMAN ◽  
M. S. DELIBALTA ◽  
R. COMAKLI
Keyword(s):  
Regression Analysis ◽  
Los Angeles ◽  
Multiple Regression Analysis ◽  
Multiple Regression ◽  
Noise Level ◽  
Regression Equation ◽  
Abrasion Loss ◽  
Los Angeles Abrasion ◽  
Indirect Tests ◽  
Simple Regression

Compared to the indirect tests, the determination of the Los Angeles abrasion loss is time consuming and expensive, and requires a large amount of samples. For this reason, the prediction of Los Angeles abrasion loss from some indirect tests is useful for preliminary studies. In this study, Los Angeles abrasion, noise level (NL) measurement, density, and porosity tests were carried out on 27 different rock types such as igneous, metamorphic, and sedimentary. The test results were evaluated using the simple and multiple regression analysis. A good relation was found between the Los Angeles abrasion loss and the NL. In order to check the possibility of obtaining more significant relations, multiple regression analysis was performed by including density and porosity values. However, the regression analysis showed that the correlation coefficients of the multiple regression equations were slightly higher than that of the simple regression equation. Since the simple regression equation is practical and statistically significant, it is suggested for estimation purpose. In conclusion, it can be said that Los Angeles abrasion loss of aggregates can be reliably estimated from NL measurement.

scholarly journals EVALUATING THE SAWABILITY OF ROCKS BY CHAIN-SAW MACHINES USING THE PROMETHEE TECHNIQUE

2021 ◽  
Vol 36 (1) ◽  
pp. 25-36
Author(s):  
Reza Mikaeil ◽  
Akbar Esmaeilzadeh ◽  
Sara Aghaei ◽  
Sina Shaffiee Haghshenas ◽  
Amir Jafarpour ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Los Angeles ◽  
Production Rate ◽  
Physical And Mechanical Properties ◽  
Dimension Stone ◽  
Quartz Content ◽  
Los Angeles Abrasion ◽  
Production Values ◽  
Schmidt Hardness ◽  
Dimension Stone Quarry

One of the most significant factors in the estimation of dimension stone quarry cost is the production rate of rock cutting machines. Evaluating the production rate of chain-saw machines is a very significant and practical issue. In this research, it has been attempted to evaluate and select the suitable working-face for a quarry by examining the maximum production rate in the Dehbid and Shayan marble quarries. For this purpose, fi eld studies were carried out which included measuring operational characteristics of the chain-saw cutting machine, the production rate and sampling for laboratory tests from seven active case studies. Subsequently, the physical and mechanical properties of rocks including: Uniaxial Compressive Strength (UCS), Brazilian Tensile Strength (BTS), Los Angeles abrasion, quartz content, water absorption percentage, porosity, Schmidt hardness and grain size for all sample measurements were studied after transferring the samples to a rock-mechanics laboratory. Finally, the sawability of the quarried working-faces was evaluated using the PROMETHEE multi-criteria decision-making (MCDM) model according to the physical and mechanical properties. The results of the study indicated that the number 1 and 5 working-faces from the Dehbid and Shayan quarries are the most suitable working-faces in terms of production rate with the maximum recorded production values (4.95 and 3.1 m2 /h), and with net fl ow rates (2.67 and -0.36) respectively.

scholarly journals The Impact of Secondary Phyllosilicate Minerals on the Engineering Properties of Various Igneous Aggregates from Greece

Minerals ◽  
2018 ◽  
Vol 8 (8) ◽  
pp. 329 ◽  
Author(s):  
Petros Petrounias ◽  
Panagiota Giannakopoulou ◽  
Aikaterini Rogkala ◽  
Paraskevi Lampropoulou ◽  
Eleni Koutsopoulou ◽  
...  
Keyword(s):  
Regression Analysis ◽  
Los Angeles ◽  
Moisture Content ◽  
Total Porosity ◽  
Physicomechanical Properties ◽  
Engineering Properties ◽  
Petrographic Analysis ◽  
Rock Samples ◽  
Los Angeles Abrasion ◽  
The Impact

This paper investigates the effect of alteration on the physicomechanical properties of igneous rocks used as aggregates, from various areas from Greece. The studied lithologies include serpentinized dunites, serpentinized harzburgites, serpentinized lherzolites, metamorphic gabbros, diabases, dacites and andesites. Quantitative petrographic analysis shows that the tested samples display various percentages of secondary phyllosilicate minerals. Mineral quantification of the studied rock samples was performed by using the Rietveld method on X-ray diffraction patterns. The samples were also tested to assign moisture content (w (%)), total porosity (nt (%)), uniaxial compressive strength (UCS (MPa)) and Los Angeles abrasion test (LA (%)). The influence of secondary phyllosilicate minerals on the physicomechanical behavior of the tested samples was determined using regression analysis and their derived equations. Regression analysis shows a positive relationship between the percentage of the phyllosilicate minerals of the rocks and the moisture content as well as with the total porosity values. In mafic and ultramafic rock samples, the relationships between the secondary phyllosilicate minerals and their physicomechanical properties have shown that the total amount of the secondary phyllosilicate minerals results negatively on their physicomechanical properties. On the other hand, the low percentage of phyllosilicate minerals in volcanic rocks can’t be able to define their engineering properties.

scholarly journals The effect of coarse aggregate hardness on the fracture toughness and compressive strength of concrete

2019 ◽  
Vol 258 ◽  
pp. 04011
Author(s):  
Atur P. N. Siregar ◽  
Emma L. Pasaribu ◽  
I Wayan Suarnita
Keyword(s):  
Fracture Toughness ◽  
Compressive Strength ◽  
Los Angeles ◽  
Coarse Aggregate ◽  
Concrete Aggregate ◽  
Beam Size ◽  
Intensity Factors ◽  
Coarse Aggregates ◽  
Los Angeles Abrasion ◽  
Compressive Strength Of Concrete

Coarse aggregate is the dominant constituent in concrete. Aggregate hardness is a variable needed to investigate in determining its effect on the critical stress intensity factors (KIC), dissipated fracture energy (Gf) and compressive strength (fc’) of the concrete. The hardness of coarse aggregate based on Los Angeles abrasion values of 16.7%., 22.6%, and 23.1% was used incorporated with Portland Composite Cement (PCC), and superplasticizer to create specimens. Cubes of 150x150x150 mm were employed to determine the fc’, and four beam sizes: 50x100x350 mm, 50x150x500 mm, 50x300x950 mm and 50x450x1250 mm were engaged to determine KIC and Gf. The fc’ and Gf of specimens manufactured by three different hardness of coarse aggregates were 45, 43, 40 MPa and 89.4, 54.0, 56.3 N/m respectively. KIC of specimens was 138.9, 119.4 and 114.1 MPa.mm1/2 for beam size of 50x100x350 mm; 148.2, 115.8 and 108.8 MPa.mm1/2 for beam size of 50x150x500 mm; 230.9, 183.1 and 157.9 MPa.mm1/2 for beam size of 50x300x950 mm; and 293.2, 248.1 and 244.3 MPa.mm1/2 for beam size of 50x450x1250 mm. Experimental results showed that decreasing hardness of coarse aggregate was found to have significant effect on the fracture toughness rather than on the compressive strength of concrete.

Micro-Deval Testing of Aggregates in the Southeast

2003 ◽  
Vol 1837 (1) ◽  
pp. 73-79 ◽  
Author(s):  
L. Allen Cooley ◽  
Robert S. James
Keyword(s):  
Los Angeles ◽  
Magnesium Sulfate ◽  
Impact Test ◽  
Southeastern United States ◽  
Test Results ◽  
Performance Category ◽  
Los Angeles Abrasion ◽  
National Cooperative ◽  
Highway Research

Aggregate used in hot-mix asphalt (HMA) must be tough and durable, not only to withstand the effects of HMA production, transportation, and construction but also to resist the effects of traffic and the environment. Historically, the Los Angeles abrasion and impact test has determined the toughness of aggregates. The long-term durability characteristics of aggregates are generally determined using a soundness test: sodium or magnesium sulfate. During the National Cooperative Highway Research Program’s Project 4–19, the micro-Deval test, in conjunction with the magnesium sulfate soundness test, were recommended in lieu of the Los Angeles abrasion and impact test and other soundness tests. Therefore, a study was needed within the southeastern United States to evaluate the range in micro-Deval results that could be expected. This research characterized the toughness and durability of aggregates with respect to their micro-Deval test results. Seventy-two aggregate sources from eight different states were included in this research. These aggregates were rated as good, fair, or poor with respect to performance by the contributing state. On the basis of the results of this study, some large differences were found in micro-Deval test results within a given performance category. There was no relationship between Los Angeles abrasion and impact and micro-Deval test results.

Sign in / Sign up

Export Citation Format

Share Document