Analysis of Chip Formation of AISI 52100 Steel During Hard Turning with Newly Developed HSN2 Coated Carbide Insert

2020 ◽  
pp. 429-437
Author(s):  
Anupam Alok ◽  
Manas Das
Keyword(s):  
Chip Formation ◽  
Hard Turning ◽  
Aisi 52100 ◽  
Aisi 52100 Steel ◽  
Coated Carbide ◽  
Carbide Insert

scholarly journals Machining force comparison for surface defect hard turning and conventional hard turning of AISI 52100 steel

2021 ◽  
Vol 13 (3) ◽  
pp. 205-214
Author(s):  
P. U MAMAHESWARRAO ◽  
D. RANGARAJU ◽  
K. N. S. SUMAN ◽  
B. RAVISANKAR
Keyword(s):  
Hard Turning ◽  
Surface Defect ◽  
Cutting Speed ◽  
Tool Geometry ◽  
Depth Of Cut ◽  
Nose Radius ◽  
Aisi 52100 ◽  
Machining Force ◽  
Aisi 52100 Steel ◽  
The Impact

In this article, a recently developed method called surface defect machining (SDM) for hard turning has been adopted and termed surface defect hard turning (SDHT). The main purpose of the present study was to explore the impact of cutting parameters like cutting speed, feed, depth of cut, and tool geometry parameters such as nose radius and negative rake angle of the machining force during surface defect hard turning (SDHT) of AISI 52100 steel in dry condition with Polycrystalline cubic boron nitride (PCBN) tool; and results were compared with conventional hard turning (CHT). Experimentation is devised and executed as per Central Composite Design (CCD) of Response Surface Methodology (RSM). Results reported that an average machining force was decreased by 22% for surface defect hard turning (SDHT) compared to conventional hard turning (CHT).

Effect of Cutting-Edge Geometry and Workpiece Hardness on Surface Residual Stresses in Finish Hard Turning of AISI 52100 Steel

1999 ◽  
Author(s):  
Jeffrey D. Thiele ◽  
Shreyes N. Melkote ◽  
Roberta A. Peascoe ◽  
Thomas R. Watkins
Keyword(s):  
Residual Stresses ◽  
Hard Turning ◽  
Cutting Edge ◽  
Phase Changes ◽  
Edge Geometry ◽  
Surface Residual Stresses ◽  
Aisi 52100 ◽  
High Feed ◽  
Aisi 52100 Steel ◽  
Finish Hard Turning

Abstract An experimental investigation was conducted to determine the effects of tool cutting-edge geometry and workpiece hardness on surface residual stresses for finish hard turning of through-hardened AISI 52100 steel. Polycrystalline cubic boron nitride (PCBN) inserts with representative types of edge geometry including “up-sharp” edges, edge hones, and chamfers, were used as the cutting tools in this study. This study shows that tool edge geometry is highly influential with respect to surface residual stresses, which were measured using x-ray diffraction. In general, compressive surface residual stresses in the axial and circumferential directions were generated by large edge hone tools, for longitudinal turning operations. Residual stresses in the axial and circumferential directions generated by small edge hone tools are typically more tensile than stresses produced by large edge hone tools. Microstructural analysis shows that thermal effects are significant at high feed rates, based on the presence of phase changes on the workpiece surface. At high feed rates, compressive stresses correlate with continuous white layers and tensile stresses correlate with over-tempered regions on the surface of the workpiece. Mechanical effects play a larger role at low feed rates, where phase changes are not observed to a significant degree. For these cases, large edge hone tools generally produce more compressive values of residual stress than small edge hone tools.

Effect of Cutting-Edge Geometry and Workpiece Hardness on Surface Residual Stresses in Finish Hard Turning of AISI 52100 Steel

1999 ◽  
Vol 122 (4) ◽  
pp. 642-649 ◽  
Author(s):  
Jeffrey D. Thiele ◽  
Shreyes N. Melkote ◽  
Roberta A. Peascoe ◽  
Thomas R. Watkins
Keyword(s):  
Residual Stresses ◽  
Hard Turning ◽  
Cutting Edge ◽  
Edge Geometry ◽  
Surface Residual Stresses ◽  
Aisi 52100 ◽  
Aisi 52100 Steel ◽  
Finish Hard Turning ◽  
Hardness Values ◽  
Compressive Residual Stresses

An experimental investigation was conducted to determine the effects of tool cutting-edge geometry (edge preparation) and workpiece hardness on surface residual stresses for finish hard turning of through-hardened AISI 52100 steel. Polycrystalline cubic boron nitride (PCBN) inserts with representative types of edge geometry including “up-sharp” edges, edge hones, and chamfers were used as the cutting tools in this study. This study shows that tool edge geometry is highly influential with respect to surface residual stresses, which were measured using x-ray diffraction. In general, compressive surface residual stresses in the axial and circumferential directions were generated by large edge hone tools in longitudinal turning operations. Residual stresses in the axial and circumferential directions generated by large edge hone tools are typically more compressive than stresses produced by small edge hone tools. Microstructural analysis shows that thermally-induced phase transformation effects are present at all feeds and workpiece hardness values with the large edge hone tools, and only at high feeds and hardness values with the small edge hone tools. In general, continuous white layers on the workpiece surface correlate with compressive residual stresses, while over-tempered regions correlate with tensile or compressive residual stresses depending on the workpiece hardness. [S1087-1357(00)00304-X]

Sign in / Sign up

Export Citation Format

Share Document