Preparation and processing of complex viscose yarns with an increased elementary fibre content

1985 ◽  
Vol 16 (3) ◽  
pp. 168-170
Author(s):  
S. P. Mendelevskaya ◽  
N. T. Butkova ◽  
A. B. Pakshver ◽  
G. G. Finger ◽  
V. A. Lasavichyus
Keyword(s):  
Fibre Content ◽  
Complex Viscose ◽  
Elementary Fibre

Yield and quality evaluation of ginger (Zingiber officinale Rosc) genotypes under high rainfall zone of Tamil Nadu

1970 ◽  
pp. 95
Author(s):  
R Balakumbahan ◽  
J P Joshua
Keyword(s):  
Tamil Nadu ◽  
Quality Evaluation ◽  
Zingiber Officinale ◽  
Fibre Content ◽  
Research Station ◽  
Local Strains ◽  
High Rainfall ◽  
Yield And Quality ◽  
Rainfall Region ◽  
Horticultural Research

An experiment on ginger was undertaken between April 2012 to March 2015 at Horticultural Research Station, Pechiparai with an objective to identify suitable ginger cultivar or accession with higher yield and quality attributes suitable for high rainfall zone of Tamil Nadu. Twenty four ginger genotypes, local strains and varieties were collected from different ginger growing tracts of India and evaluated for their performance in high rainfall region. Among the twenty four genotypes tested, the accession Z. O- 4 recorded higher fresh rhizome yield (22.16 ha-1) than other genotypes whereas Z. O - 6 recorded highest dry recovery per cent (22.47%). Higher oleoresin and fibre content was recorded in genotypes Z. O – 5 (9.56%) and Z . O – 17 (11.20%) respectively. 

The influence of fibres on the structure of thermally dried sludge product

1996 ◽  
Vol 34 (3-4) ◽  
pp. 469-473
Author(s):  
Paul Lowe ◽  
Michael Brown ◽  
Kathleen Hudson
Keyword(s):  
Bulk Density ◽  
Fibre Content ◽  
High Concentration ◽  
Secondary Sludge ◽  
Limited Experience ◽  
Apparent Reason ◽  
Drying Technology ◽  
Dried Sludge ◽  
Lower Bulk Density ◽  
The Relationship

There appears to be a limited experience world-wide in the application of thermal drying technology to processing raw undigested sludge. This limited experience has shown that the products from raw sludge processing have a much lower bulk density than those from digested sludge. The apparent reason for this phenomenon demonstrated by this work, is the high concentration of fibres in the raw undigested sludge. Different sludges show varying degrees of fibre concentration with a decrease in fibre content as the proportion of secondary sludge increases. The relationship between the bulk density of the product and the fibre content are given and this shows that as the fibre content increases the bulk density of the product will fall. It is recommended that a compaction/pelletisation stage is included in the process stream for high fibre sludges.

Optimizing the effects of Persian gum and carrot pomace powder for development of low-fat donut with high fibre content

2017 ◽  
Vol 9 ◽  
pp. 39-45 ◽  
Author(s):  
Mehran Nouri ◽  
Behzad Nasehi ◽  
Vahid Samavati ◽  
Saman Abdanan Mehdizadeh
Keyword(s):  
Fibre Content ◽  
Low Fat ◽  
High Fibre ◽  
High Fibre Content

Effect of fibre content on the mechanical properties of hemp fibre woven fabrics/polypropylene composite laminates

2021 ◽  
pp. 096739112110239
Author(s):  
Sheedev Antony ◽  
Abel Cherouat ◽  
Guillaume Montay
Keyword(s):  
Mechanical Properties ◽  
Polymer Matrix ◽  
Composite Laminates ◽  
Volume Fraction ◽  
Fibre Volume Fraction ◽  
Fibre Volume ◽  
Woven Fabrics ◽  
Fibre Content ◽  
Viscoelastic Behaviour ◽  
Hemp Fibre

Nowadays natural fibre composites have gained great significance as reinforcements in polymer matrix composites. Composite material based on a polymer matrix reinforced with natural fibres is extensively used in industry due to their biodegradability, recyclability, low density and high specific properties. A study has been carried out here to investigate the fibre volume fraction effect of hemp fibre woven fabrics/PolyPropylene (PP) composite laminates on the tensile properties and impact hammer impact test. Initially, composite sheets were fabricated by the thermal-compression process with desired number of fabric layers to obtain composite laminates with different fibre volume fraction. Uniaxial, shear and biaxial tensile tests were performed and mechanical properties were calculated. Impact hammer test was also carried out to estimate the frequency and damping parameters of stratified composite plates. Scanning Electron Microscope (SEM) analysis was performed to observe the matrix and fibre constituent defects. Hemp fabrics/PP composite laminates exhibits viscoelastic behaviour and as the fibre volume fraction increases, the viscoelastic behaviour decreases to elastic behaviour. Due to this, the tensile strength increases as the fibre content increases. On the other hand, the natural frequency increases and damping ratio decrease as the fibre volume fraction increases.

Identification of quantitative trait loci (QTL) controlling fibre content of sugarcane ( Saccharum hybrids spp.)

2021 ◽  
Author(s):  
Md S. Islam ◽  
Yong‐Bao Pan ◽  
Lionel Lomax ◽  
Michael P. Grisham
Keyword(s):  
Quantitative Trait Loci ◽  
Quantitative Trait ◽  
Fibre Content ◽  
Trait Loci

LINURON ADSORPTION AND THE DEGREE OF DECOMPOSITION OF PEATS AS MEASURED BY RUBBED FIBRE CONTENT AND PYROPHOSPHATE INDEX

1976 ◽  
Vol 56 (2) ◽  
pp. 105-109 ◽  
Author(s):  
H. MORITA
Keyword(s):  
Adsorption Isotherms ◽  
Fibre Content ◽  
Extraction Technique ◽  
Adsorption Coefficient ◽  
Column Extraction

Determination of the Freundlich adsorption isotherms for linuron with some peats showed that the adsorption coefficient, K, is closely related to the degree of decomposition as measured by the rubbed fibre content and the pyrophosphate index. The K values indicate that adsorption increases with decomposition. The analyses required for the determination of K were facilitated by the use of a column extraction technique.

Changes in fibre content and degradability during preservation of grass–clover crops

2011 ◽  
Vol 168 (1-2) ◽  
pp. 122-130 ◽  
Author(s):  
A.K. Bakken ◽  
Å.T. Randby ◽  
P. Udén
Keyword(s):  
Fibre Content
Sign in / Sign up

Export Citation Format

Share Document