Effect of frequency of pulsing in gas tungsten arc welding on the microstructure and mechanical properties of titanium alloy welds: A technical note

1996 ◽  
Vol 15 (7) ◽  
pp. 626-628 ◽  
Author(s):  
T. Mohandas ◽  
G. Madhusudan Reddy
Keyword(s):  
Mechanical Properties ◽  
Titanium Alloy ◽  
Arc Welding ◽  
Technical Note ◽  
Gas Tungsten Arc Welding ◽  
Gas Tungsten Arc ◽  
Microstructure And Mechanical Properties ◽  
Gas Tungsten

scholarly journals Microstructure and Mechanical Properties of Fe-36Ni and 304L Dissimilar Alloy Lap Joints by Pulsed Gas Tungsten Arc Welding

Materials ◽  
2020 ◽  
Vol 13 (18) ◽  
pp. 4016
Author(s):  
Qian Wang ◽  
Junqi Shen ◽  
Shengsun Hu ◽  
Guancheng Zhao ◽  
Jie Zhou
Keyword(s):  
Mechanical Properties ◽  
Arc Welding ◽  
Tensile Force ◽  
Lap Joints ◽  
Gas Tungsten Arc Welding ◽  
Lower Sheet ◽  
Gas Tungsten Arc ◽  
Microstructure And Mechanical Properties ◽  
Dissimilar Alloys ◽  
Gas Tungsten

High-quality joining of dissimilar alloys between Fe-36Ni alloy and 304L stainless steel is essential in the manufacturing of LNG tanker. In this study, lap joints of Fe-36Ni and 304L dissimilar alloys were fabricated by a pulsed gas tungsten arc welding (P-GTAW) process. The effects of low-frequency pulse on the appearance, microstructure and mechanical properties of the Fe-36Ni/304L lap joints was investigated. With the increase of frequency, the feature sizes of α (the transition angle of the upper surface of Fe-36Ni to the surface of the weld bead) and R (shortest distance between weld root and weld surface) exhibited downtrend and uptrend, respectively, while La (the maximum weld width of lower sheet) and P (the maximum weld penetration of lower sheet) changed in a smaller range. Fusion zone (FZ) is mainly composed of γ phase and M23C6 during solidification, and M23C6 particles are distributed on the grain boundaries of the cells, which reduced the mechanical properties of joint. The average hardness between 110 HV1 and 136 HV1 is lower than that of the base metals. Fractures of all joints located at the Fe-36Ni side near the weld, and a dimple fracture in all samples indicated a ductile fracture. This study found that the heat input values remain 198.86 J mm−1 and increased pulse frequency can improve the maximum tensile force. The average maximum tensile force of the lap weld is 11.95 kN when pulsed frequency is 15 Hz.

scholarly journals Microstructure and Mechanical Properties of Clad(A4045/A3003) Al Alloy by Gas Tungsten Arc Welding

2008 ◽  
Vol 26 (4) ◽  
pp. 73-78
Author(s):  
Ki-Bin Kim ◽  
Jin-Seon Gook ◽  
Dong-Ju Yoon ◽  
Byung-Il Kim ◽  
Il-Cheon Lee
Keyword(s):  
Mechanical Properties ◽  
Arc Welding ◽  
Gas Tungsten Arc Welding ◽  
Al Alloy ◽  
Gas Tungsten Arc ◽  
Microstructure And Mechanical Properties ◽  
Gas Tungsten

Effect of arc pulsing in gas tungsten arc welding on microstructure and mechanical properties of Ti–6Al–4V-2.5Cu

2020 ◽  
Vol 784 ◽  
pp. 139318 ◽  
Author(s):  
Gajula Gowthami ◽  
G.V.S. Nageswara Rao ◽  
Amit Bhattacharjee ◽  
G. Madhusudhan Reddy
Keyword(s):  
Mechanical Properties ◽  
Arc Welding ◽  
Gas Tungsten Arc Welding ◽  
Gas Tungsten Arc ◽  
Microstructure And Mechanical Properties ◽  
Gas Tungsten
Sign in / Sign up

Export Citation Format

Share Document