Elastic-plastic state of a coiled cylindrical shell loaded with internal pressure

1983 ◽  
Vol 19 (1) ◽  
pp. 32-37 ◽  
Author(s):  
L. A. Il'in ◽  
N. A. Lobkova
Keyword(s):  
Cylindrical Shell ◽  
Internal Pressure ◽  
Plastic State ◽  
Elastic Plastic

Elasto-plastic state of curve beam system subjected to complex loading

1996 ◽  
Vol 18 (4) ◽  
pp. 14-22
Author(s):  
Vu Khac Bay
Keyword(s):  
Cylindrical Shell ◽  
Solution Method ◽  
Complex Loading ◽  
Numerical Results ◽  
Elastic Solution ◽  
Plastic State ◽  
Curve Beam ◽  
Elastic State ◽  
Elastic Plastic ◽  
Beam System

Investigation of the elastic state of curve beam system had been considered in [3]. In this paper the elastic-plastic state of curve beam system in the form of cylindrical shell is analyzed by the elastic solution method. Numerical results of the problem and conclusion are given.

On Thick-Walled Cylinder Under Internal Pressure

2003 ◽  
Vol 125 (3) ◽  
pp. 267-273 ◽  
Author(s):  
W. Zhao ◽  
R. Seshadri ◽  
R. N. Dubey
Keyword(s):  
Internal Pressure ◽  
Strain Curve ◽  
Stress Strain ◽  
Piecewise Linearization ◽  
Elastic Plastic ◽  
Plastic Cylinder ◽  
Parametric Functions ◽  
The Difference ◽  
New Formulation ◽  
Walled Cylinder

A technique for elastic-plastic analysis of a thick-walled elastic-plastic cylinder under internal pressure is proposed. It involves two parametric functions and piecewise linearization of the stress-strain curve. A deformation type of relationship is combined with Hooke’s law in such a way that stress-strain law has the same form in all linear segments, but each segment involves different material parameters. Elastic values are used to describe elastic part of deformation during loading and also during unloading. The technique involves the use of deformed geometry to satisfy the boundary and other relevant conditions. The value of strain energy required for deformation is found to depend on whether initial or final geometry is used to satisfy the boundary conditions. In the case of low work-hardening solid, the difference is significant and cannot be ignored. As well, it is shown that the new formulation is appropriate for elastic-plastic fracture calculations.

Elastic-plastic bending of the pipeline under combined loading

2021 ◽  
pp. 372-377
Author(s):  
Виктор Миронович Варшицкий ◽  
Евгений Павлович Студёнов ◽  
Олег Александрович Козырев ◽  
Эльдар Намикович Фигаров
Keyword(s):  
Internal Pressure ◽  
Limit State ◽  
Bending Moment ◽  
Axial Direction ◽  
Longitudinal Force ◽  
Combined Loading ◽  
Dimensional Problem ◽  
Elastic Plastic ◽  
Pipeline Section ◽  
Thin Walled Pipe

Рассмотрена задача упругопластического деформирования тонкостенной трубы при комбинированном нагружении изгибающим моментом, осевой силой и внутренним давлением. Решение задачи осуществлено по разработанной методике с помощью математического пакета Matcad численным методом, основанным на деформационной теории пластичности и безмоментной теории оболочек. Для упрощения решения предложено сведение двумерной задачи к одномерной задаче о деформировании балки, материал которой имеет различные диаграммы деформирования при сжатии и растяжении в осевом направлении. Проведено сравнение с результатами численного решения двумерной задачи методом конечных элементов в упругопластической постановке. Результаты расчета по инженерной методике совпадают с точным решением с точностью, необходимой для практического применения. Полученные результаты упругопластического решения для изгибающего момента в сечении трубопровода при комбинированном нагружении позволяют уточнить известное критериальное соотношение прочности сечения трубопровода с кольцевым дефектом в сторону снижения перебраковки. Применение разработанной методики позволяет ранжировать участки трубопровода с непроектным изгибом по степени близости к предельному состоянию при комбинированном нагружении изгибающим моментом, продольным усилием и внутренним давлением. The problem of elastic plastic deformation of a thin-walled pipe under co-binned loading by bending moment, axial force and internal pressure is considered. The problem is solved by the developed method using the Matcad mathematical package by a numerical method based on the deformation theory of plasticity and the momentless theory of shells. To simplify the solution of the problem, it is proposed to reduce a twodimensional problem to a one-dimensional problem about beam deformation, the material of which has different deformation diagrams under compression and tension in the axial direction. Comparison with the results of numerical solution of the two-dimensional problem with the finite element method in the elastic plastic formulation is carried out. The obtained results of the elastic-plastic solution for the bending moment in the pipeline section under combined loading make it possible to clarify criterion ratio of the strength of the pipeline section with an annular defect in the direction of reducing the rejection. Application of the developed approach allows to rank pipeline sections with non-design bending in the steppe close to the limit state under combined loading of the pipeline with bending moment, longitudinal force and internal pressure.

Study of the elastic-plastic state of cyclically loaded shells of revolution

1976 ◽  
Vol 8 (4) ◽  
pp. 483-486
Author(s):  
I. S. Chernyshenko ◽  
G. K. Sharshukov
Keyword(s):  
Plastic State ◽  
Shells Of Revolution ◽  
Elastic Plastic

Elastic and elastic-plastic finite element analysis of hollow tubes with axisymmetric internal projections under combined axial and pressure loading

2001 ◽  
Vol 36 (4) ◽  
pp. 373-390 ◽  
Author(s):  
S. J Hardy ◽  
M. K Pipelzadeh ◽  
A. R Gowhari-Anaraki
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Internal Pressure ◽  
Plastic Material ◽  
Axial Loading ◽  
Material Model ◽  
Pressure Loading ◽  
Element Analysis ◽  
Elastic Plastic ◽  
Applied Loading

This paper discusses the behaviour of hollow tubes with axisymmetric internal projections subjected to combined axial and internal pressure loading. Predictions from an extensive elastic and elastic-plastic finite element analysis are presented for a typical geometry and a range of loading combinations, using a simplified bilinear elastic-perfectly plastic material model. The axial loading case, previously analysed, is extended to cover the additional effect of internal pressure. All the predicted stress and strain data are found to depend on the applied loading conditions. The results are normalized with respect to material properties and can therefore be applied to geometrically similar components made from other materials, which can be represented by the same material models.

scholarly journals Thermo elastic-plastic transition in a thin rotating disc with inclusion

2007 ◽  
Vol 11 (1) ◽  
pp. 103-118 ◽  
Author(s):  
Kumar Gupta ◽  
P Pankaj
Keyword(s):  
Thermal Effect ◽  
Internal Surface ◽  
Angular Speed ◽  
Incompressible Material ◽  
Plastic State ◽  
Percentage Increase ◽  
Compressible Material ◽  
Rotating Disc ◽  
Elastic Plastic ◽  
Different Temperatures

Stresses for the elastic-plastic transition and fully plastic state have been derived for a thin rotating disc with shaft at different temperatures and results have been discussed and depicted graphically. It has been observed that the rotating disc with inclusion and made of compressible material requires lesser angular speed to yield at the internal surface and higher percentage increase in angular speed to become fully plastic as compare to disc made of incompressible material. With the introduction of thermal effect the rotating disc with inclusion required lesser angular speed to yield at the internal surface. Rotating disc made of compressible material with inclusion requires higher percentage increase in angular speed to become fully-plastic as compare to disc made of incompressible material. Thermal effect also increases the values of radial and circumferential stresses at the internal surface for fully-plastic state. .

scholarly journals Elastic-plastic transition stresses in a transversely isotropic thick-walled cylinder subjected to internal pressure and steady-state temperature

2009 ◽  
Vol 13 (4) ◽  
pp. 107-118 ◽  
Author(s):  
Thakur Pankaj
Keyword(s):  
Steady State ◽  
Internal Pressure ◽  
Isotropic Material ◽  
Internal Surface ◽  
Transversely Isotropic ◽  
Percentage Increase ◽  
Transversely Isotropic Material ◽  
Elastic Plastic ◽  
Steady State Temperature ◽  
Walled Cylinder

Elastic-plastic transitional stresses in a transversely isotropic thick-walled cylinder subjected to internal pressure and steady-state temperature have been derived by using Seth's transition theory. The combined effects of pressure and temperature has been presented graphically and discussed. It has been observed that at room temperature, thick-walled cylinder made of isotropic material yields at a high pressure at the internal surface as compared to cylinder made of transversely isotropic material. With the introduction of thermal effects isotropic/transversely isotropic cylinder yields at a lower pressure whereas cylinder made of isotropic material requires less percentage increase in pressure to become fully-plastic from its initial yielding as compared to cylinder made of transversely isotropic material.

Sign in / Sign up

Export Citation Format

Share Document