Centrifugal casting of drill bit cones

S. G. Sultanov; T. G. Geokchaev; L. P. Kolienko

doi:10.1007/bf01156167

Preparation of cross-sectional samples for near-surface TEM studies

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s042482010012669x ◽

1987 ◽

Vol 45 ◽

pp. 380-381

Author(s):

R.C. Dickenson ◽

K.R. Lawless

Keyword(s):

Standard Sample ◽

Surface Region ◽

Specimen Preparation ◽

Thick Sheet ◽

Drill Bit ◽

Sample Holder ◽

Metal Interface ◽

Cross Sectional ◽

Near Surface ◽

Cold Worked

In thermal oxidation studies, the structure of the oxide-metal interface and the near-surface region is of great importance. A technique has been developed for constructing cross-sectional samples of oxidized aluminum alloys, which reveal these regions. The specimen preparation procedure is as follows: An ultra-sonic drill is used to cut a 3mm diameter disc from a 1.0mm thick sheet of the material. The disc is mounted on a brass block with low-melting wax, and a 1.0mm hole is drilled in the disc using a #60 drill bit. The drill is positioned so that the edge of the hole is tangent to the center of the disc (Fig. 1) . The disc is removed from the mount and cleaned with acetone to remove any traces of wax. To remove the cold-worked layer from the surface of the hole, the disc is placed in a standard sample holder for a Tenupol electropolisher so that the hole is in the center of the area to be polished.

Download Full-text

Improvement of cutting structures of a single-cone drill-bit

Equipment and Technologies for Oil and Gas Complex ◽

10.33285/1999-6934-2020-3(117)-35-38 ◽

2020 ◽

pp. 35-38

Author(s):

R.M. Bogomolov ◽

Keyword(s):

Drill Bit ◽

Single Cone ◽

Cone Drill

Download Full-text

Pengaruh Kecepatan Putar Terhadap Hasil Coran pada Metode Pengecoran Sentrifugal dalam Pembuatan Produk Pisau Pakan Ternak dengan Material Ni-Hard1

Manutech : Jurnal Teknologi Manufaktur ◽

10.33504/manutech.v11i01.92 ◽

2019 ◽

Vol 11 (01) ◽

pp. 1-7

Author(s):

Roni Kusnowo ◽

Kus Hanaldi

Keyword(s):

Animal Feed ◽

Centrifugal Casting ◽

Impact Resistance ◽

Literature Study ◽

Gravity Casting ◽

Friction Resistance ◽

Optimal Speed ◽

Mold Making

Animal feed knife is a tool that serves to cut and chop animal feed consisting of grass as the main ingredient with additives such as bran, herbs, centrate, cassava, tofu pulp and others. Therefore, as a cutting tool must have the properties of friction resistance, impact resistance, and have good sharpness, so that the material chosen is Ni-Hard 1. The use of centrifugal casting method was chosen because it has the advantage of being able to make castings with relatively thin thickness this is due to the influence of the centrifugal force on the distribution of metal liquids throughout the cavity in the mold. Case study in this study is the use of centrifugal casting methods as an alternative to gravity casting methods to overcome defects of misruns. This research was conducted to investigate the effect of speed on the formation of castings products. The method that was carried out began with a literature study on centrifugal casting, and continued by determining the material, the temperature of the cast is in the range 1250ºC - 1300ºC, and the type of mold. The next step is to do work drawings, pattern making, mold making, casting processes, fettling processes, and analysis. With variations in speed of 200 rpm, 300 rpm and 400 rpm, it can be seen the optimal speed for making this product. The results of this study obtained optimal speed at a speed of 300 rpm to make good quality of animal feed knife products.

Download Full-text