Three-dimensional analysis of fluid flow and heat transfer in single- and two-layered micro-channel heat sinks

2011 ◽  
Vol 47 (11) ◽  
pp. 1375-1383 ◽  
Author(s):  
M. L.-J. Levac ◽  
H. M. Soliman ◽  
S. J. Ormiston
Keyword(s):  
Heat Transfer ◽  
Fluid Flow ◽  
Dimensional Analysis ◽  
Three Dimensional ◽  
Heat Sinks ◽  
Micro Channel ◽  
Flow And Heat Transfer

Three-Dimensional Analysis of Fluid Flow and Heat Transfer in Single- and Two-Layered Micro-Channel Heat Sinks

2008 ◽  
Author(s):  
M. L.-J. Levac ◽  
H. M. Soliman ◽  
S. J. Ormiston
Keyword(s):  
Heat Transfer ◽  
Heat Sink ◽  
Numerical Study ◽  
Three Dimensional ◽  
Heat Sinks ◽  
Micro Channel ◽  
Flow Conditions ◽  
Flow And Heat Transfer ◽  
Computer Chips ◽  
Laminar Flow Conditions

Micro-channel heat sinks are currently at the forefront of cooling technologies for computer chips where the input heat flux is projected to exceed 100 W/cm2 [1, 2]. The quest for better heat-sink designs has produced different ideas, one of which is the idea of using multi-layered micro-channel heat sinks [3, 4]. The objectives of the present investigation were to conduct a detailed numerical study of the hydrodynamic and thermal behavior of a two-layered micro-channel heat sink and to compare the performance of the two-layered heat sink with that of a single-layered sink under laminar flow conditions.

A review of flow and heat transfer behaviour of nanofluids in micro channel heat sinks

2018 ◽  
Vol 8 ◽  
pp. 477-493 ◽  
Author(s):  
Sunil Kumar ◽  
Anil Kumar ◽  
Alok Darshan Kothiyal ◽  
Mangal Singh Bisht
Keyword(s):  
Heat Transfer ◽  
Heat Sinks ◽  
Micro Channel ◽  
Flow And Heat Transfer

Compact Modeling of Fluid Flow and Heat Transfer in Straight Fin Heat Sinks

2004 ◽  
Vol 126 (2) ◽  
pp. 247-255 ◽  
Author(s):  
Duckjong Kim ◽  
Sung Jin Kim
Keyword(s):  
Heat Transfer ◽  
Porous Medium ◽  
Fluid Flow ◽  
Pressure Drop ◽  
Heat Sink ◽  
Volume Averaging ◽  
Thermal Design ◽  
Heat Sinks ◽  
Compact Modeling ◽  
Flow And Heat Transfer

In the present work, a compact modeling method based on a volume-averaging technique is presented. Its application to an analysis of fluid flow and heat transfer in straight fin heat sinks is then analyzed. In this study, the straight fin heat sink is modeled as a porous medium through which fluid flows. The volume-averaged momentum and energy equations for developing flow in these heat sinks are obtained using the local volume-averaging method. The permeability and the interstitial heat transfer coefficient required to solve these equations are determined analytically from forced convective flow between infinite parallel plates. To validate the compact model proposed in this paper, three aluminum straight fin heat sinks having a base size of 101.43mm×101.43mm are tested with an inlet velocity ranging from 0.5 m/s to 2 m/s. In the experimental investigation, the heat sink is heated uniformly at the bottom. The resulting pressure drop across the heat sink and the temperature distribution at its bottom are then measured and are compared with those obtained through the porous medium approach. Upon comparison, the porous medium approach is shown to accurately predict the pressure drop and heat transfer characteristics of straight fin heat sinks. In addition, evidence indicates that the entrance effect should be considered in the thermal design of heat sinks when Re Dh/L>∼O10.

Verification of Finite Volume Computations on Steady-State Fluid Flow and Heat Transfer

2001 ◽  
Vol 124 (1) ◽  
pp. 11-21 ◽  
Author(s):  
J. Cadafalch ◽  
C. D. Pe´rez-Segarra ◽  
R. Co`nsul ◽  
A. Oliva
Keyword(s):  
Heat Transfer ◽  
Fluid Flow ◽  
Steady State ◽  
Finite Volume ◽  
Numerical Solutions ◽  
Three Dimensional ◽  
Independent Solution ◽  
Post Processing ◽  
Square Duct ◽  
Flow And Heat Transfer

This work presents a post-processing tool for the verification of steady-state fluid flow and heat transfer finite volume computations. It is based both on the generalized Richardson extrapolation and the Grid Convergence Index GCI. The observed order of accuracy and a error band where the grid independent solution is expected to be contained are estimated. The results corresponding to the following two and three-dimensional steady-state simulations are post-processed: a flow inside a cavity with moving top wall, an axisymmetric turbulent flow through a compressor valve, a premixed methane/air laminar flat flame on a perforated burner, and the heat transfer from an isothermal cylinder enclosed by a square duct. Discussion is carried out about the certainty of the estimators obtained with the post-processing procedure. They have been shown to be useful parameters in order to assess credibility and quality to the reported numerical solutions.

Fluid flow and heat transfer of a stratified system during natural convection – influence of chamfered corners

2019 ◽  
Vol 29 (2) ◽  
pp. 470-486 ◽  
Author(s):  
Alireza Rahimi ◽  
Aravindhan Surendar ◽  
Aygul Z. Ibatova ◽  
Abbas Kasaeipoor ◽  
Emad Hasani Malekshah
Keyword(s):  
Heat Transfer ◽  
Fluid Flow ◽  
Natural Convection ◽  
Entropy Generation ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Three Dimensional ◽  
Immiscible Fluids ◽  
Content Type ◽  
Flow And Heat Transfer

Purpose This paper aims to investigate the three-dimensional natural convection and entropy generation in the rectangular cuboid cavities included by chamfered triangular partition made by polypropylene. Design/methodology/approach The enclosure is filled by multi-walled carbon nanotubes (MWCNTs)-H2O nanofluid and air as two immiscible fluids. The finite volume approach is used for computation. The fluid flow and heat transfer are considered with combination of local entropy generation due to fluid friction and heat transfer. Moreover, a numerical method is developed based on three-dimensional solution of Navier–Stokes equations. Findings Effects of side ratio of triangular partitions (SR = 0.5, 1 and 2), Rayleigh number (103 < Ra < 105) and solid volume fraction (f = 0.002, 0.004 and 0.01 Vol.%) of nanofluid are investigated on both natural convection characteristic and volumetric entropy generation. The results show that the partitions can be a suitable method to control fluid flow and energy consumption, and three-dimensional solutions renders more accurate results. Originality/value The originality of this work is to study the three-dimensional natural convection and entropy generation of a stratified system.

A New Approach to Teaching Thermofluids Dimensional Analysis

2000 ◽  
Vol 28 (2) ◽  
pp. 174-184 ◽  
Author(s):  
Mark R. D. Davies ◽  
Tara M. Dalton
Keyword(s):  
Heat Transfer ◽  
Fluid Flow ◽  
Partial Differential Equations ◽  
Differential Equations ◽  
Dimensional Analysis ◽  
New Approach ◽  
Flow And Heat Transfer ◽  
Single Method ◽  
Approach To Teaching ◽  
Simple Equations

A new method of dimensional analysis is presented by demonstrating its application to a range of problems in fluid flow and heat transfer. The technique is a development of a previously published and accepted method of inspectional analysis. This new technique is shown to give the correct results on both simple equations with solutions, and on more complex sets of partial differential equations without solutions. This development of a single method from the simple to the complex has obvious teaching advantages.

Sign in / Sign up

Export Citation Format

Share Document