A review of flow and heat transfer behaviour of nanofluids in micro channel heat sinks

2018 ◽  
Vol 8 ◽  
pp. 477-493 ◽  
Author(s):  
Sunil Kumar ◽  
Anil Kumar ◽  
Alok Darshan Kothiyal ◽  
Mangal Singh Bisht
Keyword(s):  
Heat Transfer ◽  
Heat Sinks ◽  
Micro Channel ◽  
Flow And Heat Transfer

Three-Dimensional Analysis of Fluid Flow and Heat Transfer in Single- and Two-Layered Micro-Channel Heat Sinks

2008 ◽  
Author(s):  
M. L.-J. Levac ◽  
H. M. Soliman ◽  
S. J. Ormiston
Keyword(s):  
Heat Transfer ◽  
Heat Sink ◽  
Numerical Study ◽  
Three Dimensional ◽  
Heat Sinks ◽  
Micro Channel ◽  
Flow Conditions ◽  
Flow And Heat Transfer ◽  
Computer Chips ◽  
Laminar Flow Conditions

Micro-channel heat sinks are currently at the forefront of cooling technologies for computer chips where the input heat flux is projected to exceed 100 W/cm2 [1, 2]. The quest for better heat-sink designs has produced different ideas, one of which is the idea of using multi-layered micro-channel heat sinks [3, 4]. The objectives of the present investigation were to conduct a detailed numerical study of the hydrodynamic and thermal behavior of a two-layered micro-channel heat sink and to compare the performance of the two-layered heat sink with that of a single-layered sink under laminar flow conditions.

Two-Phase Flow and Heat Transfer in Rectangular Micro-Channels

2003 ◽  
Author(s):  
Weilin Qu ◽  
Seok-Mann Yoon ◽  
Issam Mudawar
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Flow Pattern ◽  
Two Phase Flow ◽  
Flow Patterns ◽  
Heat Sinks ◽  
Phase Flow ◽  
Micro Channel ◽  
Two Phase ◽  
Micro Channels

Knowledge of flow pattern and flow pattern transitions is essential to the development of reliable predictive tools for pressure drop and heat transfer in two-phase micro-channel heat sinks. In the present study, experiments were conducted with adiabatic nitrogen-water two-phase flow in a rectangular micro-channel having a 0.406 × 2.032 mm cross-section. Superficial velocities of nitrogen and water ranged from 0.08 to 81.92 m/s and 0.04 to 10.24 m/s, respectively. Flow patterns were first identified using high-speed video imaging, and still photos were then taken for representative patterns. Results reveal that the dominant flow patterns are slug and annular, with bubbly flow occurring only occasionally; stratified and churn flow were never observed. A flow pattern map was constructed and compared with previous maps and predictions of flow pattern transition models. Annual flow is identified as the dominant flow pattern for conditions relevant to two-phase micro-channel heat sinks, and forms the basis for development of a theoretical model for both pressure drop and heat transfer in micro-channels. Features unique to two-phase micro-channel flow, such as laminar liquid and gas flows, smooth liquid-gas interface, and strong entrainment and deposition effects are incorporated into the model. The model shows good agreement with experimental data for water-cooled heat sinks.

Compact Modeling of Fluid Flow and Heat Transfer in Straight Fin Heat Sinks

2004 ◽  
Vol 126 (2) ◽  
pp. 247-255 ◽  
Author(s):  
Duckjong Kim ◽  
Sung Jin Kim
Keyword(s):  
Heat Transfer ◽  
Porous Medium ◽  
Fluid Flow ◽  
Pressure Drop ◽  
Heat Sink ◽  
Volume Averaging ◽  
Thermal Design ◽  
Heat Sinks ◽  
Compact Modeling ◽  
Flow And Heat Transfer

In the present work, a compact modeling method based on a volume-averaging technique is presented. Its application to an analysis of fluid flow and heat transfer in straight fin heat sinks is then analyzed. In this study, the straight fin heat sink is modeled as a porous medium through which fluid flows. The volume-averaged momentum and energy equations for developing flow in these heat sinks are obtained using the local volume-averaging method. The permeability and the interstitial heat transfer coefficient required to solve these equations are determined analytically from forced convective flow between infinite parallel plates. To validate the compact model proposed in this paper, three aluminum straight fin heat sinks having a base size of 101.43mm×101.43mm are tested with an inlet velocity ranging from 0.5 m/s to 2 m/s. In the experimental investigation, the heat sink is heated uniformly at the bottom. The resulting pressure drop across the heat sink and the temperature distribution at its bottom are then measured and are compared with those obtained through the porous medium approach. Upon comparison, the porous medium approach is shown to accurately predict the pressure drop and heat transfer characteristics of straight fin heat sinks. In addition, evidence indicates that the entrance effect should be considered in the thermal design of heat sinks when Re Dh/L>∼O10.

Thermal Performance Measurement for Confined Heat Sinks by Using a Modified Transient Liquid Crystal Technique

2003 ◽  
Author(s):  
S. T. Kuo ◽  
M. P. Wang ◽  
M. C. Wu ◽  
Y. H. Hung
Keyword(s):  
Heat Transfer ◽  
Liquid Crystal ◽  
Heat Sink ◽  
Heat Sinks ◽  
Experimental Investigations ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Flow And Heat Transfer ◽  
Preheating Temperature ◽  
Parametric Studies

A series of experimental investigations with a new modified transient liquid crystal method on the studies related to the fluid flow and heat transfer characteristics in a channel installed with a heat sink have been successfully performed. The parametric studies on the local and average effective heat transfer characteristics for confined heat sinks have been explored. The influencing parameters and conditions include air preheating temperature at channel inlet, flow velocity and heat sink types. Besides, a concept of the amount of enhanced heat transfer (AEHT) is introduced and defined as the ratio of j/f. The j/f ratio is almost independent of Reynolds number for a specific confined heat sink. The j/f ratios are 0.0603 and 0.0124 for fully-confined and unconfined heat sinks, respectively.

Sign in / Sign up

Export Citation Format

Share Document