Experimental and analytical study of anisotropic strength properties of bovine cortical bone

2020 ◽  
Vol 19 (5) ◽  
pp. 1953-1963
Author(s):  
H. Mohammadi ◽  
S. Pietruszczak
Keyword(s):  
Cortical Bone ◽  
Analytical Study ◽  
Strength Properties ◽  
Anisotropic Strength

scholarly journals Study of anisotropic strength properties of shale

2019 ◽  
Vol 36 (1) ◽  
pp. 93
Author(s):  
Danzhu Zheng ◽  
Stefan Miska ◽  
Małgorzata Ziaja ◽  
Jianguo Zhang
Keyword(s):  
Strength Properties ◽  
Anisotropic Strength

Identification of preferential pathways in the pore microstructure of metallurgical coke and links to anisotropic strength properties

Fuel ◽  
2021 ◽  
Vol 296 ◽  
pp. 120688
Author(s):  
Karen M. Steel ◽  
David R. Jenkins ◽  
Reydick D. Balucan ◽  
Merrick R. Mahoney
Keyword(s):  
Strength Properties ◽  
Metallurgical Coke ◽  
Anisotropic Strength ◽  
Pore Microstructure ◽  
Preferential Pathways

SEM Study of Tension Wood Fiber Morphology and its Effect on Paper Properties

1977 ◽  
Vol 35 ◽  
pp. 308-309
Author(s):  
K. W. Robinson
Keyword(s):  
Tension Wood ◽  
Wood Fiber ◽  
Strength Properties ◽  
Fiber Morphology ◽  
Paper Properties ◽  
Pure Cellulose ◽  
Short Rotation ◽  
Hardwood Trees ◽  
Sem Study

Tension wood (TW) is an abnormal tissue of hardwood trees; although it has been isolated from most parts of the tree, it is frequently found on the upper side of branches and leaning stems. TW has been classically associated with geotropic alignment, but more recently it has been associated with fast growth. Paper made from TW is generally lower in strength properties. Consequently, the paper industries' growing dependence on fast growing, short- rotation trees will result in higher amounts of TW in the final product and a corresponding reduction in strength.Relatively few studies have dealt with the role of TW in the structure of paper. It was suggested that the lower strength properties of TW were due to a combination of factors, namely, its unique morphology, compression failures in the cell wall, and lower hemicellulose content. Central to the unique morphology of the TW fiber is the thick gelatinous layer (G-layer) composed almost entirely of pure cellulose.

Pullout Strength of Screws in Foal Third Metacarpal Bone after Overdrilling a 4.5 mm Hole

1998 ◽  
Vol 11 (04) ◽  
pp. 200-204 ◽  
Author(s):  
K. Kelly ◽  
G. S. Martin ◽  
D. J. Burba ◽  
S. A. Sedrish ◽  
R. M. Moore
Keyword(s):  
Cortical Bone ◽  
Metacarpal Bone ◽  
Pullout Strength ◽  
Cancellous Screw ◽  
Bone Screw ◽  
Screw Insertion ◽  
Holding Power ◽  
Cortical Screw ◽  
Metaphyseal Bone

SummaryThe purpose of the study was to determine and to compare the in vitro pullout strength of 5.5 mm cortical versus 6.5 mm cancellous bone screws inserted in the diaphysis and metaphysis of foal third metacarpal (MCIII) bones in threaded 4.5 mm cortical bone screw insertion holes that were then overdrilled with a 4.5 mm drill bit. This information is relevant to the selection of a replacement screw if a 4.5 mm cortical screw is stripped during orthopaedic surgery. In vitro pullout tests were performed in two independent cadaver studies, each consisting of 12 foal MCIII bones. Two 4.5 mm cortical screws were placed either in the mid-diaphysis (study 1) or distal metaphysis (study 2) of MCIII bones. The holes were then overdrilled with a 4.5 mm bit and had either a 5.5 mm cortical or a 6.5 mm cancellous screw inserted; screw pullout tests were performed at a rate of 0.04 mm/s until screw or bone failure occurred.The bone failed in all of the tests in the diaphyseal and metaphyseal bone. The holding power for 6.5 mm cancellous screws was significantly (p <0.05) greater than for 5.5 mm cortical screws in both the diaphysis and metaphysis. There was not any difference in the holding power of screws in either the diaphysis or the metaphysis between proximal and distal screw holes.If a 4.5 mm cortical bone screw strips in MCIII diaphyseal or metaphyseal bone of foals, a 6.5 mm cancellous screw would provide greater holding power than a 5.5 mm cortical screw.In order to provide information regarding selection of a replacement screw if a 4.5 mm cortical screw is stripped, the in vitro pullout strength was determined for 5.5 mm cortical and 6.5 mm cancellous screws inserted in third metacarpal diaphyseal and metaphyseal bone of foals in which threaded 4.5 mm cortical bone screw insertion holes had been overdrilled with a 4.5 mm bit. The holding power of the 6.5 mm cancellous screw was significantly greater than the 5.5 mm cortical screw in both the diaphysis and metaphysis of foal third metacarpal bone. Thus, it appears that if a 4.5 mm cortical screw is stripped during orthopaedic surgery in foals, a 6.5 mm cancellous screw would provide superior holding power.

Glucocorticoid-induced loss of cortical bone is exacerbated during cold-exposure in male mice

2019 ◽  
Author(s):  
M Gado ◽  
M Noll ◽  
A Heinrich ◽  
M Rauner ◽  
LC Hofbauer ◽  
...  
Keyword(s):  
Cortical Bone ◽  
Cold Exposure ◽  
Male Mice
Sign in / Sign up

Export Citation Format

Share Document