Evaluation of the Role of Devulcanized Rubber on the Thermo-mechanical Properties of Polystyrene

2020 ◽  
Vol 28 (6) ◽  
pp. 1737-1748 ◽  
Author(s):  
F. Valentini ◽  
A. Dorigato ◽  
A. Pegoretti
Keyword(s):  
Mechanical Properties ◽  
Devulcanized Rubber

Development and mechanical properties of soy protein isolate-chitin nanofibers complex gel: The role of high-pressure homogenization

LWT ◽  
2021 ◽  
pp. 112090
Author(s):  
Qi-Hui Chen ◽  
Xiao-Yin Li ◽  
Chun-Lan Huang ◽  
Peng Liu ◽  
Qing-Zhu Zeng ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Pressure ◽  
Soy Protein ◽  
Soy Protein Isolate ◽  
Protein Isolate ◽  
High Pressure Homogenization ◽  
Chitin Nanofibers

Role of non-functionalized oxide nanoparticles on mechanical properties and toughening mechanisms of epoxy nanocomposites

2021 ◽  
Author(s):  
M.S. Goyat ◽  
Amrita Hooda ◽  
Tejendra K. Gupta ◽  
Kaushal Kumar ◽  
Sudipta Halder ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Oxide Nanoparticles ◽  
Epoxy Nanocomposites ◽  
Toughening Mechanisms

scholarly journals Role of carbon and nitrogen in the improvement of corrosion resistance of new powder metallurgy Co-Cr-Mo alloys

2020 ◽  
Vol 38 (3) ◽  
pp. 273-286 ◽  
Author(s):  
Cristina Garcia-Cabezon ◽  
Celia Garcia-Hernandez ◽  
Maria L. Rodriguez-Mendez ◽  
Gemma Herranz ◽  
Fernando Martin-Pedrosa
Keyword(s):  
Mechanical Properties ◽  
Corrosion Resistance ◽  
Powder Metallurgy ◽  
Nitrogen Content ◽  
Powder Metallurgy Technique ◽  
Carbon And Nitrogen ◽  
Physiological Conditions ◽  
Carbon And Nitrogen Content ◽  
Astm F75

AbstractMicrostructural changes that result in relevant improvements in mechanical properties and electrochemical behavior can be induced using different sintering conditions of ASTM F75 cobalt alloys during their processing using powder metallurgy technique. It has been observed that the increase in carbon and nitrogen content improves corrosion resistance and mechanical properties as long as the precipitation of carbides and nitrides is avoided, thanks to the use of rapid cooling in water after the sintering stage. In addition, the reduction of the particle size of the powder improves hardness and resistance to corrosion in both acid medium with chlorides and phosphate-buffered medium that simulates the physiological conditions for its use as a biomaterial. These results lead to increased knowledge of the role of carbon and nitrogen content in the behavior displayed by the different alloys studied.

Role of nano‐zirconia in the mechanical properties improvement of resin cement used for tooth fragment reattachment

2021 ◽  
Author(s):  
Baraa M. El‐Kemary ◽  
Ola M. El‐Borady ◽  
Sara A. Abdel Gaber ◽  
Talat M. Beltag
Keyword(s):  
Mechanical Properties ◽  
Resin Cement

Effect of wood particulate size on the mechanical properties of PLA biocomposite

2020 ◽  
Vol 49 (6) ◽  
pp. 465-472
Author(s):  
S. Raj Sachin ◽  
T. Kandasamy Kannan ◽  
Rathanasamy Rajasekar
Keyword(s):  
Mechanical Properties ◽  
Mechanical Characteristics ◽  
Wood Flour ◽  
Wood Particle ◽  
Poly Lactic Acid ◽  
Particle Sizes ◽  
Content Type ◽  
Particulate Size ◽  
Practical Implications

Purpose The purpose of this study is to carry out an investigation of the role of the wood particle size on the mechanical properties of poly lactic acid (PLA)-reinforced neem fiber biocomposite. Design/methodology/approach Composite test specimens were processed by reinforcing neem wood flour (NWF) in two different particle sizes, micro-sized NWF (MNWF) and nano-sized NWF (NNWF) separately into PLA. Composites were extruded at four different fiber loadings (10, 15, 20 and 25 Wt.%) into PLA matrix. The MNWF and NNWF had particle sizes varying from 5 to 15 µm and 10 to 15 nm, respectively. Findings Tensile strength, flexural strength and impact strength of PLA increased with fiber reinforcement for both the MNWF and NNWF cases. The NNWF-reinforced PLA composite at 20 Wt.% fiber loading proved to be the best composite that had outstanding mechanical properties in this research. Practical implications The developed composite can be used as a substitute for conventional plywood for furniture, building infrastructure and interior components for the automobile, aircraft and railway sectors. Originality/value A new biocomposite had been fabricated by using PLA and NWF and had been tested for its mechanical characteristics.

Role of the surface effect on the structural, electronic and mechanical properties of the carbide MXenes

2015 ◽  
Vol 111 (2) ◽  
pp. 26007 ◽  
Author(s):  
Xian-Hu Zha ◽  
Kan Luo ◽  
Qiuwu Li ◽  
Qing Huang ◽  
Jian He ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Surface Effect
Sign in / Sign up

Export Citation Format

Share Document