Evaluation of the High-Speed Drilling Technique for the Incremental Hole-Drilling Method

2012 ◽  
Vol 53 (4) ◽  
pp. 531-542 ◽  
Author(s):  
A. Nau ◽  
B. Scholtes
Keyword(s):  
High Speed ◽  
Hole Drilling ◽  
Hole Drilling Method ◽  
Incremental Hole Drilling ◽  
High Speed Drilling ◽  
Drilling Method ◽  
Drilling Technique

scholarly journals Incremental Hole-Drilling Method Vs. Thin Components: A Simple Correction Approach

2014 ◽  
Vol 996 ◽  
pp. 283-288 ◽  
Author(s):  
Esther Held ◽  
Simone Schuster ◽  
Jens Gibmeier
Keyword(s):  
Residual Stress ◽  
Thin Metal ◽  
Hole Drilling ◽  
Depth Profiles ◽  
Hole Drilling Method ◽  
Incremental Hole Drilling ◽  
Metal Sheets ◽  
Drilling Method ◽  
Measured Strain ◽  
The Impact

The incremental hole-drilling method is a widely used technique to determine residual stress depth profiles in technical components. Its application is limited in respect to the components geometry, for instance the components thickness. In this paper, a direct correction of the measured strain relaxations is proposed to consider the impact of deviant geometries, here the component thickness, on the residual stress evaluation that moreover, allows the application of commercially available evaluation software. The herein proposed approach is based on finite element simulation of the incremental hole drilling. The simulated strain relaxations for thin metal sheets are evaluated with an algorithm as used in commercially available evaluation software (i) for uncorrected data as well as (ii) for strain data corrected by the proposed correction procedure. It is shown that the correction approach leads to a significant improvement of the measurement accuracy. Further, by means of the approach residual stress depth profiles in thin metal sheets can be as usual determined using commercial evaluation software for the incremental hole-drilling method regardless of the algorithm used, i.e. differential or integral.

scholarly journals The Effect of Specimen Size on Residual Stresses in Friction Stir Welded Aluminum Components

2014 ◽  
Vol 996 ◽  
pp. 445-450 ◽  
Author(s):  
Wulf Pfeiffer ◽  
Eduard Reisacher ◽  
Michael Windisch ◽  
Markus Kahnert
Keyword(s):  
Residual Stresses ◽  
Specimen Size ◽  
Hole Drilling ◽  
X Ray Diffraction ◽  
X Ray ◽  
Friction Stir ◽  
Metal Parts ◽  
Hole Drilling Method ◽  
Incremental Hole Drilling ◽  
Drilling Method

Friction stir welding (FSW) is a well-known technique which allows joining of metal parts without severe distortion. Because FSW involves less heat input relative to conventional welding, it may be assumed that cutting specimens from larger friction stir welded components results in a negligible redistribution of residual stresses. The aim of the investigations was to verify these assumptions for a welded aluminum plate and a circumferentially-welded aluminum cylinder. Strain gage measurements, X-ray diffraction and the incremental hole drilling method were used.

Potentialities of Ultrasonics for Evaluating Residual Stresses: Influence of Microstructure

2002 ◽  
Vol 124 (3) ◽  
pp. 349-353 ◽  
Author(s):  
H. Walaszek ◽  
H. P. Lieurade ◽  
C. Peyrac ◽  
J. Hoblos ◽  
J. Rivenez
Keyword(s):  
Residual Stress ◽  
Stress Measurement ◽  
Ultrasonic Method ◽  
Thermal Relaxation ◽  
Good Control ◽  
Hole Drilling ◽  
Hole Drilling Method ◽  
Incremental Hole Drilling ◽  
Drilling Method ◽  
Ultrasonic Measurements

The good control of residual stress level in mechanical components is an important factor, particularly for a good fatigue strength of these components. This paper presents advances obtained at the technical center for mechanical engineering industries (CETIM) in the field of development of an ultrasonic method for stress measurements. This method is potentially advantageous because it is nondestructive, has good portability, and is easy to use. In the paper are discussed the results obtained with ultrasonics on steel welded plate, and a comparison is made with stress measurement obtained by incremental hole-drilling method, and X-ray diffraction. These results are also validated by thermal relaxation of the plates. The paper discusses also the microstructure influence on ultrasonic measurements and methods for adjusting the ultrasonic measurements to improve the agreement with results obtained from other techniques. In conclusion is emphasized the interest for studying the ability of the ultrasonic residual stress measurement method in different industrial cases.

Sign in / Sign up

Export Citation Format

Share Document