Microstructure and Strain Rate-Dependent Tensile Deformation Behavior of Fiber Laser-Welded Butt Joints of Dual-Phase Steels

2018 ◽  
Vol 27 (5) ◽  
pp. 2148-2165 ◽  
Author(s):  
Yang Liu ◽  
Danyang Dong ◽  
Zhiqiang Han ◽  
Zhibin Yang ◽  
Lu Wang ◽  
...  
Keyword(s):  
Strain Rate ◽  
Fiber Laser ◽  
Deformation Behavior ◽  
Tensile Deformation ◽  
Dual Phase ◽  
Butt Joints ◽  
Dual Phase Steels ◽  
Rate Dependent ◽  
Tensile Deformation Behavior

The effect of strain rates on tensile deformation of ultrafine-grained copper

2017 ◽  
Vol 31 (16-19) ◽  
pp. 1744014
Author(s):  
M. Li ◽  
Q. W. Jiang
Keyword(s):  
Strain Rate ◽  
Deformation Behavior ◽  
Room Temperature ◽  
Tensile Deformation ◽  
Strain Rates ◽  
Roll Bonding ◽  
Fracture Elongation ◽  
Tensile Deformation Behavior ◽  
Ultrafine Grained ◽  
Flow Stress Level

Tensile deformation behavior of ultrafine-grained (UFG) copper processed by accumulative roll-bonding (ARB) was studied under different strain rates at room temperature. It was found that the UFG copper under the strain rate of 10[Formula: see text] s[Formula: see text] led to a higher strength (higher flow stress level), flow stability (higher stress hardening rate) and fracture elongation. In the fracture surface of the sample appeared a large number of cleavage steps under the strain rate of 10[Formula: see text] s[Formula: see text], indicating a typical brittle fracture mode. When the strain rate is 10[Formula: see text] or 10[Formula: see text] s[Formula: see text], a great amount of dimples with few cleavage steps were observed, showing a transition from brittle to plastic deformation with increasing strain rate.

Effects of temperature and strain rate on tensile deformation behavior of superalloy UNS N10276

2017 ◽  
Vol 699 ◽  
pp. 88-98 ◽  
Author(s):  
Enxiang Pu ◽  
Wenjie Zheng ◽  
Zhigang Song ◽  
Han Feng ◽  
Feng Yang ◽  
...  
Keyword(s):  
Strain Rate ◽  
Deformation Behavior ◽  
Tensile Deformation ◽  
Tensile Deformation Behavior ◽  
Effects Of Temperature

Tensile Deformation Behavior of 5A90 Al-Li Alloy Sheet at Elevated Temperature

2011 ◽  
Vol 66-68 ◽  
pp. 70-75 ◽  
Author(s):  
Gao Shan Ma ◽  
Song Yang Zhang ◽  
Han Ying Wang ◽  
Min Wan
Keyword(s):  
Flow Stress ◽  
Strain Rate ◽  
Deformation Behavior ◽  
Tensile Deformation ◽  
Alloy Sheet ◽  
Hot Forming ◽  
Uniaxial Tensile ◽  
Sensitivity Index ◽  
Tensile Deformation Behavior ◽  
Increasing Temperature

Uniaxial tensile deformation behavior of 5A90 aluminium-lithium alloy sheet is investigated in the hot forming with the temperature range of 200-450°C and strain rate range of 0.3×10-3-0.2×10-1s-1. It is found that the flow stress of 5A90 Al-Li alloy in uniaxial tension increase with increasing strain rate and decrease with increasing temperature, however, the tendency of total elongation is just the reverse, and the optimum forming temperature is 400°C. The strain rate sensitivity index (m-value) remarkably increases with increasing temperature for a given strain rate. It is shown that 5A90 Al-Li alloy sheet displays the sensitivity to the strain rate at elevated temperatures. For a given strain rate, the strain hardening index (n-value) decreases with increasing temperature, whereas the n-value increases above 350°C. The constitutive equation of stress, strain and strain rate for 5A90 Al-Li alloy at any temperature is obtained by fitting the experimental data, which gave a good flow stress model for the FEM simulation of hot forming.

Effects of Strain Rate on Tensile Deformation Behavior of Quenching and Partitioning Steel

2013 ◽  
Vol 749 ◽  
pp. 401-406 ◽  
Author(s):  
Chao Liu ◽  
Lei Wang ◽  
Yang Liu
Keyword(s):  
Strain Rate ◽  
Deformation Behavior ◽  
Retained Austenite ◽  
Tensile Deformation ◽  
Auto Industry ◽  
Trip Effect ◽  
Quenching And Partitioning ◽  
Tensile Deformation Behavior

The effects of strain rate on the tensile deformation behavior of quenching and partitioning (Q&P) steel applied to the auto industry were investigated. The results indicated that the strength of Q&P steel raised with increasing strain rate. The variation of elongation which presented the trend of declining (10-4 s-1~101 s-1) followed by rising to the peak (8×101 s-1) then falling again (102 s-1~103 s-1), is mainly caused by the transformation from retained austenite to martensite, namely the TRIP effect.

Sign in / Sign up

Export Citation Format

Share Document