Evaluation of Ballistic Limit Velocity Using Instrumented Indentation Test of 7xxx Aluminum Alloys After Friction Stir Welding

2020 ◽  
Author(s):  
Changhyun Cho ◽  
Seunghun Choi ◽  
Oh Min Kwon ◽  
Seungha Lee ◽  
Jong-hwan Kim ◽  
...  
Keyword(s):  
Friction Stir Welding ◽  
Aluminum Alloys ◽  
Indentation Test ◽  
Ballistic Limit ◽  
Instrumented Indentation ◽  
Friction Stir ◽  
Limit Velocity ◽  
Ballistic Limit Velocity ◽  
Instrumented Indentation Test

A Predictive Non-Dimensional Scaling Law for the Plate Perforation of Several Aluminum Alloys by Fragment-Simulating Projectiles

2019 ◽  
Author(s):  
Weinong Chen ◽  
Zherui Guo
Keyword(s):  
Aluminum Alloys ◽  
Scaling Law ◽  
Limit Equation ◽  
Ballistic Limit ◽  
Limit Velocity ◽  
Dimensional Scaling ◽  
Material Problem ◽  
Plate Perforation ◽  
Ballistic Limit Velocity ◽  
Aluminum Armor Plates

Abstract An equation was previously-presented to predict the ballistic-limit velocity for the perforation of aluminum armor plates by fragment-simulating projectiles (FSP). The ballistic-limit equation was presented in terms of dimensionless parameters so that the geometric and material problem scales are identified. Previously published predictions and data for two different FSP projectile calibers (12.7 mm and 20 mm) and two different strength aluminum alloys show the scaling law to be accurate. In this paper we extend the same concept to several other alloys and show that this scaling law is predictive.

Mechanical property and characterization of 7A04-T6 aluminum alloys bonded by friction stir welding

2020 ◽  
Vol 52 ◽  
pp. 263-269 ◽  
Author(s):  
Jianing Li ◽  
Molin Su ◽  
Wenjun Qi ◽  
Chen Wang ◽  
Peng Zhao ◽  
...  
Keyword(s):  
Mechanical Property ◽  
Friction Stir Welding ◽  
Aluminum Alloys ◽  
Friction Stir

Friction Stir Welding of Dissimilar A319 and A413 Cast Aluminum Alloys

2014 ◽  
Vol 39 (8) ◽  
pp. 6363-6373 ◽  
Author(s):  
A. Karam ◽  
T. S. Mahmoud ◽  
H. M. Zakaria ◽  
T. A. Khalifa
Keyword(s):  
Friction Stir Welding ◽  
Aluminum Alloys ◽  
Cast Aluminum ◽  
Friction Stir ◽  
Cast Aluminum Alloys

Microstructural Characterization and Temperature Analysis in Friction Stir Welding of A383/5052 Dissimilar Aluminum Alloys

2007 ◽  
Vol 561-565 ◽  
pp. 279-282 ◽  
Author(s):  
Masafumi Kokubo ◽  
Shinichi Kazui ◽  
Takao Kaneuchi ◽  
Yoshimasa Takayama ◽  
Hajime Kato ◽  
...  
Keyword(s):  
Friction Stir Welding ◽  
Aluminum Alloys ◽  
Analytical Model ◽  
Heat Generation ◽  
Microstructural Characterization ◽  
Joint Line ◽  
Experimental Temperature ◽  
Temperature Analysis ◽  
Friction Stir ◽  
Dissimilar Aluminum Alloys

Microstructural characterization and temperature analysis have been performed in friction stir welding (FSW) of A383 and 5052 dissimilar aluminum alloys. Marked difference in microstructure was observed between joints with different arrangements of materials. The temperature at four points on each side of the joint line was measured during FSW in various conditions. In addition, an analytical model assumed that the work generated by the rotation of the tool led to the work for stirring materials and heat generation of the material and the tool. The temperature of the retreating side (RS) for the joint of the advancing side (AS):A383/RS:5052 was about 50K higher than that of AS, while the temperatures of AS and RS for the joint of AS:5052/RS:A383 were almost the same. The experimental temperature could be calculated reasonably by using the model with assumption of the work for stirring the material.

Sign in / Sign up

Export Citation Format

Share Document