scholarly journals Production optimization in well-6 of Habiganj gas field, Bangladesh: a prospective application of Nodal analysis approach

2020 ◽  
Vol 10 (8) ◽  
pp. 3557-3568
Author(s):  
Md. Shaheen Shah ◽  
Md Hafijur Rahaman Khan ◽  
Ananna Rahman ◽  
Stephen Butt
Keyword(s):  
Optimization Technique ◽  
Gas Production ◽  
Production Optimization ◽  
Vertical Wells ◽  
Gas Reservoirs ◽  
Gas Field ◽  
Nodal Analysis ◽  
Prospective Application ◽  
Overall Performance ◽  
Inflow Performance

Abstract The overall performance of gas reservoirs and the optimization of production, as well as its sensitivity analysis, are affected by several factors such as reservoir pressure, well configuration and surface facilities. The Habiganj well no. 06 (HBJ-06) is one of the significant gas-producing vertical wells of the Habiganj gas field, currently producing 14.963 MMscfd of natural gas from the upper gas sand. The widely used Nodal analysis is an optimization technique to improve the performance and was applied for the HBJ-06 to increase its production rate by optimizing manners. By this analysis, each component starting from the reservoir to the outlet pressure of the separator was identified as a resistance in the system by evaluating their inflow performance relationship and vertical lift performance. The F.A.S.T. VirtuWell™ software package was used to perform this analysis, where the declinations of wellhead pressures were suggested as 1300, 1200, 1100 and 1000 psi(a) without any modification of the tubing diameter and skin factor. Hence, the respective optimized rates of the daily gas production were increased to 38.481, 40.993, 43.153 and 46.016 MMscfd. At the same time, the optimized condensate gas ratio was calculated as 0.07, 0.06, 0.06 and 0.05, associated with the optimized condensate water ratio of 0.11, 0.10, 0.09 and 0.08, respectively.

scholarly journals Evaluation of natural gas production optimization in Kailashtila gas field in Bangladesh using decline curve analysis method

2015 ◽  
Vol 50 (1) ◽  
pp. 29-38 ◽  
Author(s):  
MS Shah ◽  
HMZ Hossain
Keyword(s):  
Production System ◽  
Gas Production ◽  
Curve Analysis ◽  
Production Optimization ◽  
Reservoir Pressure ◽  
Gas Field ◽  
Wellhead Pressure ◽  
Decline Curve Analysis ◽  
Decline Curve ◽  
Overall Performance

Decline curve analysis of well no KTL-04 from the Kailashtila gas field in northeastern Bangladesh has been examined to identify their natural gas production optimization. KTL-04 is one of the major gas producing well of Kailashtila gas field which producing 16.00 mmscfd. Conventional gas production methods depend on enormous computational efforts since production systems from reservoir to a gathering point. The overall performance of a gas production system is determined by flow rate which is involved with system or wellbore components, reservoir pressure, separator pressure and wellhead pressure. Nodal analysis technique is used to performed gas production optimization of the overall performance of the production system. F.A.S.T. Virtu Well™ analysis suggested that declining reservoir pressure 3346.8, 3299.5, 3285.6 and 3269.3 psi(a) while signifying wellhead pressure with no changing of tubing diameter and skin factor thus daily gas production capacity is optimized to 19.637, 24.198, 25.469, and 26.922 mmscfd, respectively.Bangladesh J. Sci. Ind. Res. 50(1), 29-38, 2015

A Dynamic Workflow of Well Health Issue Prediction – Sulfur Deposition

2021 ◽  
Author(s):  
Bashirul Haq
Keyword(s):  
Material Balance ◽  
Gas Production ◽  
Health Issue ◽  
Sulfur Deposition ◽  
Gas Reservoirs ◽  
Gas Field ◽  
Actual Performance ◽  
Sulphur Deposition ◽  
Balance Analysis ◽  
Sour Gas

Abstract Sour gas reservoirs are vital sources for natural gas production. Sulphur deposition in the reservoir reduces a considerable amount of gas production due to permeability reduction. Consequently, well health monitoring and early prediction of Sulphur deposition are crucial for effective gas production from a sour gas reservoir. Dynamic gas material balance analysis is a useful technique in calculating gas initially in place utilizing the flowing wellhead or bottom hole pressures and rates during the well's lifetime. The approach did not apply to monitor a producing gas's health well and detect Sulphur deposition. This work aims to (i) modify dynamic gas material balance equation by adding the Sulphur deposition term, (ii) build a model to predict and validate the issue utilizing the modified equation. A unique form of the flowing material balance is developed by including Sulphur residue term. The curve fitting tool and modified flowing gas material balance are applied to predict well-expected behaviour. The variation between expected and actual performance indicates the health issue of a well. Initial, individual components of the model are tested. Then the model is validated with the known values. The workflow is applied to active gas field and correctly detected the health issue. The novel workflow can accurately predict Sulphur evidence. Besides,the workflow can notify the production engineers to take corrective measures about the subject. Keywords: Sulfur deposition, Dynamic gas material balance analysis, Workflow

Research and Application of Material Corrosion Prevention Technology in the Completed well System for Sour Gas well

2013 ◽  
Vol 712-715 ◽  
pp. 1096-1099
Author(s):  
Ling Feng Li
Keyword(s):  
Steel Corrosion ◽  
Gas Production ◽  
Corrosion Prevention ◽  
Gas Reservoirs ◽  
Gas Field ◽  
Gas Well ◽  
Corrosion Resistant Alloy ◽  
System Life ◽  
Sour Gas

For natural gas well in sour gas reservoirs, very serious corrosion in the completed well system is an important factor of gas production system life. In order to ensure the long-term development of gas wells, this paper mainly introduces material corrosion prevention technology in the completed well system, such as corrosion-resistant alloy steel corrosion control technology, bimetallic combination tubing, corrosion inhibitor technology and so on. By taking LJ Gas Field as an example, this paper introduces the material corrosion prevention technology in the completed well system in LJ Gas Field. For application in the completed well system in LJ Gas Field, the technology above have good performance of corrosion resistance.

Non-Darcy Binomial Deliverability Equations for Partially Penetrating Vertical Gas Wells and Horizontal Gas Wells

2009 ◽  
Author(s):  
Tao Zhu ◽  
Jing Lu
Keyword(s):  
Bottom Water ◽  
Horizontal Wells ◽  
Vertical Wells ◽  
Gas Wells ◽  
Gas Reservoirs ◽  
Gas Reservoir ◽  
Gas Well ◽  
Increase Productivity ◽  
Flow Domain ◽  
Inflow Performance

Many gas reservoirs are with bottom water drive. In order to prevent or delay unwanted water into the wellbore, the producing wells are often completed as partially penetrating vertical wells, and more and more horizontal wells have been drilled in recent years in bottom water drive gas reservoirs to reduce water coning and increase productivity. For a well, non-Darcy flow is inherently a near wellbore phenomenon. In spite of the considerable study that non-Darcy behavior of fully penetrating vertical wells, there has been no study of a partially penetrating vertical well or a horizontal well in a gas reservoir with bottom water drive. This paper presents new binomial deliverability equations for partially penetrating vertical gas wells and horizontal gas wells, assuming that only radial flow occurs in the near wellbore non-Darcy’s flow domain. The inflow performance of a vertical gas well is compared with that of a horizontal gas well. The proposed equations can account for the advantages of horizontal gas wells.

Study and Application for Corrosion-Resistant Material Selection of Tubing and Casing in Sour Gas Reservoirs under Coexistence of H2S and CO2

2012 ◽  
Vol 485 ◽  
pp. 429-432
Author(s):  
Ling Feng Li ◽  
Xiao Ming Liu ◽  
Zhi Qiang Huang
Keyword(s):  
Material Selection ◽  
Gas Production ◽  
Resistant Material ◽  
Gas Reservoirs ◽  
Gas Field ◽  
Gas Well ◽  
Corrosion Resistant ◽  
Puguang Gas Field ◽  
Sour Gas ◽  
Selection Of

For natural gas well with high content of CO2 and H2S, very serious corrosion in the gas well string is an important factor of gas production system life. In order to ensure the long-term development of gas wells, this paper mainly study the corrosion-resistant material selection of tubing and casing in sour gas reservoirs under coexistence of H2S and CO2 and proposes the optimization idea and technique of tubing and casing material selection. By taking Puguang gas field as an example, this paper optimizes the material selection of production casing for Puguang gas field. By testing, the optimal materials of gas well string in Puguang gas field have good performance of erosion resistance

scholarly journals Short-Term Model-Based Production Optimization for a Gas Field in North Africa

2018 ◽  
Vol 10 (2) ◽  
pp. 65
Author(s):  
Arnaud Hoffmann
Keyword(s):  
Piecewise Linear ◽  
Treatment Plant ◽  
Gas Production ◽  
Production Optimization ◽  
Mixed Integer ◽  
Short Term ◽  
Gas Reservoir ◽  
Gas Field ◽  
Gas Treatment ◽  
Model Based

 This paper presents a model-based optimization solution suitable for short-term production optimization of large gas fields with wells producing into a common surface network into a shared gas treatment plant. The proposed methodology is applied to a field consisting of one dry gas reservoir with a CO2 content of 7.3% and one wet gas reservoir with a CO2 content of 2.8% and initial CGR of 15 stb/MMscf. 23 wells are producing, and all gas production is processed in a common gas treatment plant where condensates and CO2 are extracted from the reservoir gas. The final sales gas must honor compositional constraints (CO2 content and heating value). The proposed solution consists of a bi-level optimization algorithm. A Mixed Integer Linear Programming (MILP) formulation of the optimization problem is solved, assuming some key parameters in the gas plant to be constant. Hydraulic performances of the system, approximated using SOS2 piecewise linear models, and condensates and CO2 extraction, captured using simplified models, are included in the MILP. After solving the MILP, the values of the key parameters are calculated using a full simulation model of the gas plant and the new values are substituted in the MILP input data. This iterative procedure continues until convergence is achieved. Results show that the proposed methodology can find the optimum choke openings for all wells to maximize the total gas rate while honoring numerous surface constraints. The solution runs in 30 sec. and an average of 3-4 iterations is needed to achieve convergence. It is therefore a suitable solution for short-term production optimization and daily operations.

scholarly journals Production Optimization of Saldanadi Gas Field by Nodal Analysis Method

2010 ◽  
Author(s):  
MB Haq ◽  
E Gomes ◽  
M Tamim
Keyword(s):  
Chemical Engineering ◽  
Production Optimization ◽  
Analysis Method ◽  
Gas Field ◽  
Nodal Analysis

Journal of Chemical Engineering Vol.ChE 23 1995-2005

CoalBed Methane Pad Wells Completion and Artificial Lift Optimizations: Case Study From Australia Surat Basin DS Gas Field

2021 ◽  
Author(s):  
Li Ming ◽  
Xia Zhaohui ◽  
Liu Lingli ◽  
Cui Zehong ◽  
Duan LiJiang ◽  
...  
Keyword(s):  
Coalbed Methane ◽  
Optimization Methods ◽  
Gas Production ◽  
Production Performance ◽  
Vertical Wells ◽  
Coal Seams ◽  
Gas Field ◽  
Well Completion ◽  
Artificial Lift ◽  
Coalbed Methane Production

Abstract The Coalbed Methane in Australia Surat Basin is main gas source for LNG project in east coast of Australia[1]. Traditionally, Coalbed Methane are drilled by vertical wells. But there are big intensively farmed land coverage in the Surat Basin, the multiple wells on single, larger pad from the surface, the bores slant away at around 70 degrees to intersect multiple, thin coal seams are applied to avoid the extra "footprint" and decrease the environment affect. Many pad wells production failure because of poor interburden isolation. Excessive solids production in pad wells resulted in new failures of holes in tubing due to accelerated erosion, which bring big challenges for the Coalbed methane production in deviated pad wells. The gas production in pad wells are analysised and the new pad wells optimization are proposed. First, the complete wire log (at least include GR and density log curves) need to acquire for correct thin coal seams correlation and locate the interburden sandstone position for future good sandstone isolation. Second the customized completion strategy and placement (swell packer) are applied in the pad wells and specialized tubing with enhanced erosion resistance to extend the run life. Thirdly ESP pumps and optimized tubing are installed in new deviated wells for good gas production. After the pad wells were put into production, the gas production was kept well for long time without pump problems. Swell able packer completion significantly eliminates sand problem by isolating in excess of or close to 80% of interburden sand. The above well completion and artificial lift optimization methods bring good production performance for the new pad wells and contribute much production for the producing gas field. The swellable packer completion also can be used in vertical wells and will be standard well completion methods for future gas development wells.

Sign in / Sign up

Export Citation Format

Share Document