scholarly journals Performance evaluation of coated carbide tool in machining of stainless steel (AISI 202) under minimum quantity lubrication (MQL)

2015 ◽  
Vol 2 (2) ◽  
pp. 123-129 ◽  
Author(s):  
J. S. Dureja ◽  
Ranjit Singh ◽  
Talwinder Singh ◽  
Pargat Singh ◽  
Manu Dogra ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Performance Evaluation ◽  
Minimum Quantity Lubrication ◽  
Carbide Tool ◽  
Minimum Quantity ◽  
Coated Carbide Tool ◽  
Steel Aisi ◽  
Coated Carbide ◽  
Stainless Steel Aisi

scholarly journals Performance of TiAlN PVD coated carbide tool in machining AISI 4340 with Minimum Quantity Lubrication (MQL) condition

2021 ◽  
Vol 1034 (1) ◽  
pp. 012099
Author(s):  
Mahros Darsin ◽  
Rika Dwi Hidayatul Qoryah ◽  
Robertus Sidartawan ◽  
Allen Luviandy ◽  
Aris Zainul Muttaqin ◽  
...  
Keyword(s):  
Minimum Quantity Lubrication ◽  
Carbide Tool ◽  
Minimum Quantity ◽  
Coated Carbide Tool ◽  
Coated Carbide ◽  
Aisi 4340

Impact on Machining of AISI H13 Steel Using Coated Carbide Tool under Vegetable Oil Minimum Quantity Lubrication

2019 ◽  
Vol 8 (1) ◽  
pp. 20190154 ◽  
Author(s):  
R. Vishal ◽  
K. Nimel Sworna Ross ◽  
G. Manimaran ◽  
B. K. Gnanavel
Keyword(s):  
Vegetable Oil ◽  
Minimum Quantity Lubrication ◽  
Carbide Tool ◽  
H13 Steel ◽  
Minimum Quantity ◽  
Aisi H13 Steel ◽  
Coated Carbide Tool ◽  
Aisi H13 ◽  
Coated Carbide

Machinability investigation and sustainability assessment in hard turning of AISI D3 steel with coated carbide tool under nanofluid minimum quantity lubrication-cooling condition

2021 ◽  
pp. 095440622199384
Author(s):  
Lalatendu Dash ◽  
Smita Padhan ◽  
Anshuman Das ◽  
Sudhansu Ranjan Das
Keyword(s):  
Surface Roughness ◽  
Power Consumption ◽  
Sustainability Assessment ◽  
Flank Wear ◽  
Cutting Speed ◽  
Minimum Quantity Lubrication ◽  
Carbide Tool ◽  
Minimum Quantity ◽  
Coated Carbide Tool ◽  
Coated Carbide

The present research addresses the machinability of hardened die steel (AISI D3, 61HRC) in hard turning using multilayer (TiCN/Al2O3/TiN) coated carbide tool under nanofluid based minimum quantity lubrication-cooling condition, where no previous data are available. Power consumption, flank wear, chip morphology and surface integrity (microhardness, residual stress, white layer formation, machined surface morphology, and surface roughness) are considered as technological performance characteristics to evaluate the machinability. Combined approach of central composite design - analysis of variance, response surface methodology and desirability function analysis have been employed respectively for experimental investigation, predictive modelling and multi-response optimization. With a motivational philosophy of “Go Green-Think Green-Act Green”, the work also deals with energy saving carbon footprint analysis and sustainability assessment to recognize the green manufacturing in the context of safer and cleaner production. under environmental-friendly nanofluid assisted minimum quantity lubrication condition. The quantitative analysis revealed that the cutting speed influenced the power consumption during hard machining (75.78%) and flank wear of coated carbide tool (45.67%); feed rate impacted the surface finish of the machined part (68.8%) significantly. Saw tooth shapes of chip produced due to cyclic cracking. Due to low percentage contribution of error (5.32% to Ra, 6.64% to VB, and 7.79% to Pc), a higher correlation coefficient (R2) was obtained with the quadratic regression model, which showed values of 0.9, 0.88 and 0.92 for surface roughness, flank wear, and power consumption, respectively. Optimization with the highest desirability (0.9173) resulted the optimum machining conditions under NFMQL at the cutting speed of 57 m/min, depth of cut 0.1 mm, feed of 0.07 mm/rev, and insert’s nose radius of 0.4 mm. As a result, under NFMQL tool life was improved by 30.8% and 22.6% in respect of flank wear and surface roughness respectively than when machining with MQL technique by adapting the optimum machining condition. Therefore, using hard nanoparticles-reinforced cutting fluid under minimum quantity lubrication condition in practical manufacturing becomes very promising to improve sustainability.

Performance evaluation of coated carbide tool during face milling of AISI 304 under different cutting environments

2019 ◽  
Vol 6 (5) ◽  
pp. 056546 ◽  
Author(s):  
Pragat Singh ◽  
J S Dureja ◽  
Harwinder Singh ◽  
M S Bhatti
Keyword(s):  
Performance Evaluation ◽  
Face Milling ◽  
Carbide Tool ◽  
Aisi 304 ◽  
Coated Carbide Tool ◽  
Coated Carbide

Analysis of the performance of coated carbide cutting tools in the machining of martensitic stainless steel aisi 410 in dry and mql conditions

2018 ◽  
Vol 6 (1) ◽  
pp. 016512 ◽  
Author(s):  
M A de Paula ◽  
M V Ribeiro ◽  
J V C Souza ◽  
M Y Kondo
Keyword(s):  
Stainless Steel ◽  
Martensitic Stainless Steel ◽  
Cutting Tools ◽  
Steel Aisi ◽  
Coated Carbide ◽  
Stainless Steel Aisi

Hard Machining of Stainless Steel Using Wiper Coated Carbide: Tool Life and Surface Integrity

2010 ◽  
Vol 25 (6) ◽  
pp. 370-377 ◽  
Author(s):  
Denni Kurniawan ◽  
Noordin Mohd. Yusof ◽  
Safian Sharif
Keyword(s):  
Stainless Steel ◽  
Tool Life ◽  
Surface Integrity ◽  
Hard Machining ◽  
Carbide Tool ◽  
Coated Carbide Tool ◽  
Coated Carbide
Sign in / Sign up

Export Citation Format

Share Document