Effect of Bismuth on Preventing Chunky Graphite in High-Silicon Ductile Iron Castings

2020 ◽  
Vol 14 (4) ◽  
pp. 1052-1062 ◽  
Author(s):  
Branko Bauer ◽  
Ivana Mihalic Pokopec ◽  
Mitja Petrič ◽  
Primož Mrvar
Keyword(s):  
Ductile Iron ◽  
Iron Castings ◽  
Chunky Graphite ◽  
High Silicon

scholarly journals Experimental Evidence for Metallurgical Modification Associated to Chunky Graphite in Heavy-Section Ductile Iron Castings

2012 ◽  
Vol 6 (1) ◽  
pp. 35-42 ◽  
Author(s):  
J. Lacaze ◽  
I. Asenjo ◽  
S. Méndez ◽  
J. Sertucha ◽  
P. Larrañaga ◽  
...  
Keyword(s):  
Experimental Evidence ◽  
Ductile Iron ◽  
Iron Castings ◽  
Heavy Section ◽  
Chunky Graphite

On the solidification sequence of ductile iron castings containing chunky graphite

2005 ◽  
Vol 413-414 ◽  
pp. 346-351 ◽  
Author(s):  
Rikard Källbom ◽  
K. Hamberg ◽  
M. Wessén ◽  
L.-E. Björkegren
Keyword(s):  
Ductile Iron ◽  
Iron Castings ◽  
Solidification Sequence ◽  
Chunky Graphite

Effect of Yttrium and Magnesium Segregation on Microstructure and Mechanical Properties of Heavy Section Ductile Iron Castings

2011 ◽  
Vol 295-297 ◽  
pp. 1010-1016 ◽  
Author(s):  
Wei Ping Chen ◽  
Zhe Liu ◽  
Yu Deng ◽  
Jie Luo ◽  
Yong Cheng Chen
Keyword(s):  
Mechanical Properties ◽  
Ductile Iron ◽  
Magnesium Content ◽  
Solidification Mode ◽  
Iron Casting ◽  
Iron Castings ◽  
Microstructure And Mechanical Properties ◽  
Chunky Graphite ◽  
Main Factor ◽  
Ductile Iron Casting

Ductile iron specimen with dimensions of Φ590mm×800mm were prepared by treating the melt with an yttrium-containing nodulizer. Cooling curves at four locations____the center location, the location 85mm distant from the center, the location 170mm distant from the center and the location 255mm distant from the center of the heavy ductile iron casting Φ590mm×800mm was obtained. The effect of yttrium and magnesium on microstructure and mechanical properties was investigated, and the factors on the distribution of chunky graphite in the specimen were discussed as well. The results show that the largest amount of chunky graphite and the lowest mechanical properties appear at the location 170mm distant from the center. Excessive yttrium and magnesium content at the location 170mm distant from the center is the main factor for the large amount of chunky graphite. The characteristics of the solidification mode____pasty solidification and the considerably long solidification of the casting are the basic reasons for the distribution of chunky graphite of the heavy ductile iron casting Φ590mm×800mm.

scholarly journals Effect of inoculation on the formation of chunky graphite in ductile-iron castings

2017 ◽  
Vol 51 (2) ◽  
pp. 275-281 ◽  
Author(s):  
I. Mihalic Pokopec ◽  
P. Mrvar ◽  
B. Bauer
Keyword(s):  
Ductile Iron ◽  
Iron Castings ◽  
Chunky Graphite

ALLOYING OF THIN-WALL DUCTILE IRON CASTINGS

2016 ◽  
Author(s):  
Stephanie Tankersley
Keyword(s):  
Ductile Iron ◽  
Thin Wall ◽  
Iron Castings

scholarly journals New Possibilities of Shaping the Surface Properties in Austempered Ductile Iron Castings

2013 ◽  
Vol 13 (1) ◽  
pp. 103-106 ◽  
Author(s):  
D. Myszka
Keyword(s):  
Surface Layer ◽  
Surface Properties ◽  
Ductile Iron ◽  
Shot Peening ◽  
Austempered Ductile Iron ◽  
Protective Atmosphere ◽  
Detonation Spraying ◽  
Iron Castings ◽  
Recent Developments ◽  
Commercial Applications

Abstract The paper presents recent developments concerning the formation of surface layer in austempered ductile iron castings. It was found that the traditional methods used to change the properties of the surface layer, i.e. the effect of protective atmosphere during austenitising or shot peening, are not fully satisfactory to meet the demands of commercial applications. Therefore, new ways to shape the surface layer and the surface properties of austempered ductile iron castings are searched for, to mention only detonation spraying, carbonitriding, CVD methods, etc.

scholarly journals Influence of Technological Parameters of Furane Mixtures on Shrinkage Creation in Ductile Cast Iron Castings

2014 ◽  
Vol 59 (3) ◽  
pp. 1037-1040 ◽  
Author(s):  
I. Vasková ◽  
M. Hrubovčáková ◽  
J. Malik ◽  
Š. Eperješi
Keyword(s):  
Cast Iron ◽  
Ductile Iron ◽  
Ductile Cast Iron ◽  
Gating System ◽  
Technological Parameters ◽  
Iron Castings ◽  
Steel Castings ◽  
The Impact ◽  
Very High ◽  
Great Development

Abstract Ductile cast iron (GS) has noticed great development in last decades and its boom has no analogue in history humankind. Ductile iron has broaden the use of castings from cast iron into areas, which where exclusively domains for steel castings. Mainly by castings, which weight is very high, is the propensity to shrinkage creation even higher. Shrinkage creation influences mainly material, construction of casting, gating system and mould. Therefore, the main realized experiment was to ascertain the influence of technological parameters of furane mixture on shrinkage creation in castings from ductile iron. Together was poured 12 testing items in 3 moulds forto determine and compare the impact of various technological parameters forms the propensity for shrinkage in the casting of LGG.

scholarly journals Multiscale Microstructural Analysis of Austempered Ductile Iron Castings

2017 ◽  
Vol 23 (S1) ◽  
pp. 350-351
Author(s):  
Kemal Davut ◽  
Alp Yalcin ◽  
Baris Cetin
Keyword(s):  
Ductile Iron ◽  
Microstructural Analysis ◽  
Austempered Ductile Iron ◽  
Iron Castings
Sign in / Sign up

Export Citation Format

Share Document