Study on the flare tip of a gas refinery with various designs of windshields using CFD simulations

2020 ◽  
Vol 37 (1) ◽  
pp. 227-236
Author(s):  
Taleb Zarei ◽  
Ali Akbar Ezadi
Keyword(s):  
Cfd Simulations ◽  
Gas Refinery

CFD SIMULATIONS OF POOL BOILING WITH VARIOUS HEATER WALL CONDITIONS

2018 ◽  
Author(s):  
Yeong Shin Jeong ◽  
In Cheol Bang
Keyword(s):  
Pool Boiling ◽  
Cfd Simulations ◽  
Heater Wall

Comparison of DSMC and CFD Models of Heat Transfer in a Rarefied Two-Dimensional Geometry

2018 ◽  
Author(s):  
Dilesh Maharjan ◽  
Mustafa Hadj-Nacer ◽  
Miles Greiner ◽  
Stefan K. Stefanov
Keyword(s):  
Heat Transfer ◽  
Rarefied Gas ◽  
Complex Geometry ◽  
Direct Simulation Monte Carlo ◽  
Accurate Method ◽  
Vacuum Drying ◽  
Helium Pressure ◽  
Two Dimensional ◽  
Dsmc Method ◽  
Cfd Simulations

During vacuum drying of used nuclear fuel (UNF) canisters, helium pressure is reduced to as low as 67 Pa to promote evaporation and removal of remaining water after draining process. At such low pressure, and considering the dimensions of the system, helium is mildly rarefied, which induces a thermal-resistance temperature-jump at gas–solid interfaces that contributes to the increase of cladding temperature. It is important to maintain the temperature of the cladding below roughly 400 °C to avoid radial hydride formation, which may cause cladding embrittlement during transportation and long-term storage. Direct Simulation Monte Carlo (DSMC) method is an accurate method to predict heat transfer and temperature under rarefied condition. However, it is not convenient for complex geometry like a UNF canister. Computational Fluid Dynamics (CFD) simulations are more convenient to apply but their accuracy for rarefied condition are not well established. This work seeks to validate the use of CFD simulations to model heat transfer through rarefied gas in simple two-dimensional geometry by comparing the results to the more accurate DSMC method. The geometry consists of a circular fuel rod centered inside a square cross-section enclosure filled with rarefied helium. The validated CFD model will be used later to accurately estimate the temperature of an UNF canister subjected to vacuum drying condition.

Effect of ring baffle configuration in a self-priming venturi scrubber using CFD simulations

Particuology ◽  
2019 ◽  
Vol 47 ◽  
pp. 63-69
Author(s):  
Shuai Yang ◽  
Xiangdi Zhao ◽  
Wanfu Sun ◽  
Jiwu Yuan ◽  
Zheng Wang
Keyword(s):  
Cfd Simulations ◽  
Venturi Scrubber

Incorporation of Taguchi approach with CFD simulations on laser welding of spacer grid fuel rod assembly

2021 ◽  
Vol 269 ◽  
pp. 115182
Author(s):  
G. Satyanarayana ◽  
K.L. Narayana ◽  
B. Nageswara Rao
Keyword(s):  
Laser Welding ◽  
Taguchi Approach ◽  
Cfd Simulations ◽  
Spacer Grid ◽  
Fuel Rod

Feasibility of full-core pin resolved CFD simulations of small modular reactor with momentum sources

2021 ◽  
Vol 378 ◽  
pp. 111143
Author(s):  
Jun Fang ◽  
Dillon R. Shaver ◽  
Ananias Tomboulides ◽  
Misun Min ◽  
Paul Fischer ◽  
...  
Keyword(s):  
Cfd Simulations ◽  
Small Modular Reactor ◽  
Full Core

Performance enhancement of Savonius wind turbine by blade shape and twisted angle modifications

2021 ◽  
pp. 095765092098794
Author(s):  
Ahmed M Nagib Elmekawy ◽  
Hassan A Hassan Saeed ◽  
Sadek Z Kassab
Keyword(s):  
Wind Turbine ◽  
Performance Enhancement ◽  
Three Dimensional ◽  
Turbulence Models ◽  
Vertical Axis ◽  
Cfd Simulations ◽  
Sliding Mesh ◽  
Blade Shape ◽  
Rotor Shape ◽  
Twisting Angle

Three-dimensional CFD simulations are carried out to study the increase of power generated from Savonius vertical axis wind turbines by modifying the blade shape and blade angel of twist. Twisting angle of the classical blade are varied and several proposed novel blade shapes are introduced to enhance the performance of the wind turbine. CFD simulations have been performed using sliding mesh technique of ANSYS software. Four turbulence models; realizable k -[Formula: see text], standard k - [Formula: see text], SST transition and SST k -[Formula: see text] are utilized in the simulations. The blade twisting angle has been modified for the proposed dimensions and wind speed. The introduced novel blade increased the power generated compared to the classical shapes. The two proposed novel blades achieved better power coefficients. One of the proposed models achieved an increase of 31% and the other one achieved 32.2% when compared to the classical rotor shape. The optimum twist angel for the two proposed models achieved 5.66% and 5.69% when compared with zero angle of twist.

scholarly journals Radial Turbine Design for Solar Chimney Power Plants

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 674
Author(s):  
Paul Caicedo ◽  
David Wood ◽  
Craig Johansen
Keyword(s):  
Power Plants ◽  
Reference Frames ◽  
Three Dimensional ◽  
Discrete Ordinates ◽  
Large Area ◽  
Solar Chimney ◽  
Cfd Simulations ◽  
Radial Turbine ◽  
Design Changes ◽  
Turbine Design

Solar chimney power plants (SCPPs) collect air heated over a large area on the ground and exhaust it through a turbine or turbines located near the base of a tall chimney to produce renewable electricity. SCPP design in practice is likely to be specific to the site and of variable size, both of which require a purpose-built turbine. If SCPP turbines cannot be mass produced, unlike wind turbines, for example, they should be as cheap as possible to manufacture as their design changes. It is argued that a radial inflow turbine with blades made from metal sheets, or similar material, is likely to achieve this objective. This turbine type has not previously been considered for SCPPs. This article presents the design of a radial turbine to be placed hypothetically at the bottom of the Manzanares SCPP, the only large prototype to be built. Three-dimensional computational fluid dynamics (CFD) simulations were used to assess the turbine’s performance when installed in the SCPP. Multiple reference frames with the renormalization group k-ε turbulence model, and a discrete ordinates non-gray radiation model were used in the CFD simulations. Three radial turbines were designed and simulated. The largest power output was 77.7 kW at a shaft speed of 15 rpm for a solar radiation of 850 W/m2 which exceeds by more than 40 kW the original axial turbine used in Manzanares. Further, the efficiency of this turbine matches the highest efficiency of competing turbine designs in the literature.

scholarly journals Using CFD to Evaluate Natural Ventilation through a 3D Parametric Modeling Approach

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2197
Author(s):  
Nayara Rodrigues Marques Sakiyama ◽  
Jurgen Frick ◽  
Timea Bejat ◽  
Harald Garrecht
Keyword(s):  
Natural Ventilation ◽  
Parametric Modeling ◽  
Cfd Simulations ◽  
3D Design ◽  
Post Process ◽  
Test House ◽  
Model Set ◽  
Computational Fluid Dynamics Cfd ◽  
Set Up ◽  
Passive Strategy

Predicting building air change rates is a challenge for designers seeking to deal with natural ventilation, a more and more popular passive strategy. Among the methods available for this task, computational fluid dynamics (CFD) appears the most compelling, in ascending use. However, CFD simulations require a range of settings and skills that inhibit its wide application. With the primary goal of providing a pragmatic CFD application to promote wind-driven ventilation assessments at the design phase, this paper presents a study that investigates natural ventilation integrating 3D parametric modeling and CFD. From pre- to post-processing, the workflow addresses all simulation steps: geometry and weather definition, including incident wind directions, a model set up, control, results’ edition, and visualization. Both indoor air velocities and air change rates (ACH) were calculated within the procedure, which used a test house and air measurements as a reference. The study explores alternatives in the 3D design platform’s frame to display and compute ACH and parametrically generate surfaces where air velocities are computed. The paper also discusses the effectiveness of the reference building’s natural ventilation by analyzing the CFD outputs. The proposed approach assists the practical use of CFD by designers, providing detailed information about the numerical model, as well as enabling the means to generate the cases, visualize, and post-process the results.

Sign in / Sign up

Export Citation Format

Share Document