99mTc bone scanning agents—I. influence of experimental conditions on the formation and gel chromatography of 99mTc(Sn)pyrophosphate complexes

1985 ◽  
Vol 12 (2) ◽  
pp. 83-88 ◽  
Author(s):  
J. Kroesbergen ◽  
W.J. Gelsema ◽  
C.L. De Ligny
Author(s):  
Danail Georgiev ◽  
Georgi Dobrev ◽  
Stefan Shilev

Aim: To characterize the enzyme phytase produced by phytase-active Candida melibiosica 2491 for subsecuent use in feed industry. Methods: C. melibiosica 2491 had been selected among 118 strains as the most productive strain of phytase. In present study, the enzyme was first purified through electrophoresis grade in four steps: precipitation with organic solvent, ultrafiltration, gel chromatography and Denaturing gel electrophoresis (SDS–PAGE). Results: Higher levels of purification were obtained using ethanol. The gel chromatography showed an elution maximum at 11-12 fractions that characterize the corresponding one as high-molecular weight phytase. The purification level was found to be 19.5 folds with specific enzyme activity of 2.75 U/mg protein and yield – 19.64 %. Furthermore, the molecular weight of purified phytase was estimated to 35.9 кDa, with optimum of pH – at 4.5 and optimum of temperature at 55 °C. Maximum phytase activity in case of whole cells was found at 50 оС, which was less than using the purified enzyme. It was activated through 5 mM of Ba2+, 10 mM of Mn2+ and K+ ions. Total inhibition effect was achieved from Fe3+, Hg2+ and Zn2+. Copper ions (Cu2+) in concentrations at 5 mM conducted to partial inhibition effect, but at 10 mM the phytase activity was equal to zero. Low inhibition effect was determined in case of cobalt ions (Co2+) at concentrations of 10 mM. The phytase displayed broad sub­strate specificity and the Km for phytate was estimated to be 0.21 mM under the experimental conditions, while Vmax – 19.9 µМ/ml. Conclusion: Although the phytase produced by C. melibiosica 2491 is a promising enzyme to be used successfully in feed production, more investigations are needed to ensure its advantages.


Author(s):  
F. I. Grace ◽  
L. E. Murr

During the course of electron transmission investigations of the deformation structures associated with shock-loaded thin foil specimens of 70/30 brass, it was observed that in a number of instances preferential etching occurred along grain boundaries; and that the degree of etching appeared to depend upon the various experimental conditions prevailing during electropolishing. These included the electrolyte composition, the average current density, and the temperature in the vicinity of the specimen. In the specific case of 70/30 brass shock-loaded at pressures in the range 200-400 kilobars, the predominant mode of deformation was observed to be twin-type faults which in several cases exhibited preferential etching similar to that observed along grain boundaries. A novel feature of this particular phenomenon was that in certain cases, especially for twins located in the vicinity of the specimen edge, the etching or preferential electropolishing literally isolated these structures from the matrix.


Author(s):  
Nalin J. Unakar

The increased number of lysosomes as well as the close approximation of lysosomes to the Golgi apparatus in tissue under variety of experimental conditions is commonly observed. These observations suggest Golgi involvement in lysosomal production. The role of the Golgi apparatus in the production of lysosomes in mouse liver was studied by electron microscopy of liver following toxic injury by CCI4.


Author(s):  
N. J. Zaluzec

The ultimate sensitivity of microchemical analysis using x-ray emission rests in selecting those experimental conditions which will maximize the measured peak-to-background (P/B) ratio. This paper presents the results of calculations aimed at determining the influence of incident beam energy, detector/specimen geometry and specimen composition on the P/B ratio for ideally thin samples (i.e., the effects of scattering and absorption are considered negligible). As such it is assumed that the complications resulting from system peaks, bremsstrahlung fluorescence, electron tails and specimen contamination have been eliminated and that one needs only to consider the physics of the generation/emission process.The number of characteristic x-ray photons (Ip) emitted from a thin foil of thickness dt into the solid angle dΩ is given by the well-known equation


Author(s):  
V. Annamalai ◽  
L.E. Murr

Economical recovery of copper metal from leach liquors has been carried out by the simple process of cementing copper onto a suitable substrate metal, such as scrap-iron, since the 16th century. The process has, however, a major drawback of consuming more iron than stoichiometrically needed by the reaction.Therefore, many research groups started looking into the process more closely. Though it is accepted that the structural characteristics of the resultant copper deposit cause changes in reaction rates for various experimental conditions, not many systems have been systematically investigated. This paper examines the deposit structures and the kinetic data, and explains the correlations between them.A simple cementation cell along with rotating discs of pure iron (99.9%) were employed in this study to obtain the kinetic results The resultant copper deposits were studied in a Hitachi Perkin-Elmer HHS-2R scanning electron microscope operated at 25kV in the secondary electron emission mode.


Author(s):  
R. H. Morriss ◽  
J. D. C. Peng ◽  
C. D. Melvin

Although dynamical diffraction theory was modified for electrons by Bethe in 1928, relatively few calculations have been carried out because of computational difficulties. Even fewer attempts have been made to correlate experimental data with theoretical calculations. The experimental conditions are indeed stringent - not only is a knowledge of crystal perfection, morphology, and orientation necessary, but other factors such as specimen contamination are important and must be carefully controlled. The experimental method of fine-focus convergent-beam electron diffraction has been successfully applied by Goodman and Lehmpfuhl to single crystals of MgO containing light atoms and more recently by Lynch to single crystalline (111) gold films which contain heavy atoms. In both experiments intensity distributions were calculated using the multislice method of n-beam diffraction theory. In order to obtain reasonable accuracy Lynch found it necessary to include 139 beams in the calculations for gold with all but 43 corresponding to beams out of the [111] zone.


Author(s):  
John H. L. Watson ◽  
John L. Swedo ◽  
M. Vrandecic

The ambient temperature and the nature of the storage fluids may well have significant effects upon the post-implantation behavior of venus autografts. A first step in the investigation of such effects is reported here. Experimental conditions have been set which approximate actual operating room procedures. Saphenous veins from dogs have been used as models in the experiments. After removal from the dogs the veins were kept for two hours under four different experimental conditions, viz at either 4°C or 23°C in either physiological saline or whole canine arterial blood. At the end of the two hours they were prepared for light and electron microscopy. Since no obvious changes or damage could be seen in the veins by light microscopy, even with the advantage of tissue specific stains, it was essential that the control of parameters for successful grafts be set by electron microscopy.


Sign in / Sign up

Export Citation Format

Share Document