Normal and oblique impact of a kinetic energy projectile on mild steel plates

1992 ◽  
Vol 12 (3) ◽  
pp. 333-343 ◽  
Author(s):  
N.K. Gupta ◽  
V. Madhu
Keyword(s):  
Kinetic Energy ◽  
Mild Steel ◽  
Oblique Impact ◽  
Steel Plates

Tests on Yacht Hull Plating

1996 ◽  
Vol 33 (02) ◽  
pp. 130-140
Author(s):  
K. C. Brown ◽  
P. N. Joubert ◽  
Ping Yan
Keyword(s):  
Shock Wave ◽  
Mild Steel ◽  
Explosive Charge ◽  
Failure Modes ◽  
Static Pressure ◽  
Steel Plates ◽  
Pressure Tests ◽  
Mode Of Failure ◽  
Actual Mode ◽  
Design Pressure

Static pressure tests on sections of yacht hulls, manufactured to copy the structure of certain yachts which failed in service due to slamming loads, are reported. The materials of construction were aluminum, steel, plywood and fiberglass. The failure modes and pressures are discussed. In addition, some tests in which mild steel plates, corresponding in construction to the mild steel hull tested under static pressure, were loaded impulsively by the shock wave from an explosive charge detonated in air. The design of hull plating should take into account the impulsive nature of the loading, and the actual mode of failure. Neither the design impulse, however, nor the means for predicting the hull plating response to it are available from the current literature. If resort is to be made to the design of plating for simple static pressure, then a design pressure of at least 350 kPa(51 psi) is suggested for the bottom plating of yachts of about 13 m (43 ft) length overall. This is about five times the pressure required by the ABS Guide.

KETAHANAN BALISTIK LEMBARAN BAJA PADA BERBAGAI SUDUT TEMBAK

ROTASI ◽  
2014 ◽  
Vol 16 (1) ◽  
pp. 34
Author(s):  
Rusnaldy Rusnaldy ◽  
Ismoyo Haryanto ◽  
Norman Iskandar ◽  
Binar Ade Anugra ◽  
Ahmad Zaedun
Keyword(s):  
Mild Steel ◽  
Steel Plate ◽  
Angle Of Attack ◽  
Oblique Impact ◽  
Experimental Results ◽  
Normal Impact ◽  
Impact Angles

Results of study on the performance of 0.4 mm mild steel plate when impacted by 4.5 mm diameter steel ogive-shaped projectile at 45o, 60o (oblique impact) and 90 o (normal impact) angles of attack are presented. The projectiles were fired at highest velocity using air riffle gun. The target-holding fixture was located at a distance of 2 m from the gun. Experimental results show that steel plate provides protection at 45o and 60o obliquity, but fails to provide protection at angle of attack of 90o (normal impact)

scholarly journals Microstructure Analysis of Arc Welded Mild Steel Plates

2018 ◽  
Vol 377 ◽  
pp. 012049
Author(s):  
Bijaya Kumar Khamari ◽  
Pradip Kumar Sahu ◽  
B B Biswal
Keyword(s):  
Mild Steel ◽  
Microstructure Analysis ◽  
Steel Plates

Stress Field and Deformation around a Crack Tip Evaluated by Infrared Thermography and Fracture Strength of Welded Mild Steel Plates

2003 ◽  
Vol 233-236 ◽  
pp. 127-132
Author(s):  
Isamu Oda ◽  
Andrew Willett ◽  
Mitsuharu Yamamoto ◽  
Mitsuru Miyawaki ◽  
Naoki Watanabe ◽  
...  
Keyword(s):  
Stress Field ◽  
Mild Steel ◽  
Infrared Thermography ◽  
Fracture Strength ◽  
Crack Tip ◽  
Steel Plates

Equivalent concrete thickness for perforation of mild steel plates

2017 ◽  
Vol 135 ◽  
pp. 213-229 ◽  
Author(s):  
Mohamed Abdel-Kader ◽  
Ahmed Fouda
Keyword(s):  
Mild Steel ◽  
Steel Plates
Sign in / Sign up

Export Citation Format

Share Document