scholarly journals Experimental correlations and CFD model of a non-tubular heater for a Stirling solar engine micro-cogeneration unit

2019 ◽  
Vol 153 ◽  
pp. 715-725
Author(s):  
David García ◽  
María-José Suárez ◽  
Eduardo Blanco ◽  
Jesús-Ignacio Prieto
Keyword(s):  
Cfd Model ◽  
Tubular Heater

Use CFD Model of WWER-1200 Reactor for Prediction of Fuel Assemblies Vibrations

2019 ◽  
Vol 12 (4) ◽  
pp. 62-70
Author(s):  
K.N. Proskuryakov ◽  
A.V. Anikeev ◽  
E. Afshar ◽  
D.A. Pisareva
Keyword(s):  
Cfd Model ◽  
Fuel Assemblies

Effects of Over Fire Air on the Combustion and NOx Emission Characteristics of a 600 MW Opposed Swirling Fired Boiler

2012 ◽  
Vol 512-515 ◽  
pp. 2135-2142 ◽  
Author(s):  
Yu Peng Wu ◽  
Zhi Yong Wen ◽  
Yue Liang Shen ◽  
Qing Yan Fang ◽  
Cheng Zhang ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Experimental Data ◽  
Empirical Method ◽  
Nox Emission ◽  
Emission Characteristics ◽  
Cfd Model ◽  
Nitrogen Release ◽  
Computational Fluid Dynamics Cfd ◽  
Low Nox Emission

A computational fluid dynamics (CFD) model of a 600 MW opposed swirling coal-fired utility boiler has been established. The chemical percolation devolatilization (CPD) model, instead of an empirical method, has been adapted to predict the nitrogen release during the devolatilization. The current CFD model has been validated by comparing the simulated results with the experimental data obtained from the boiler for case study. The validated CFD model is then applied to study the effects of ratio of over fire air (OFA) on the combustion and nitrogen oxides (NOx) emission characteristics. It is found that, with increasing the ratio of OFA, the carbon content in fly ash increases linearly, and the NOx emission reduces largely. The OFA ratio of 30% is optimal for both high burnout of pulverized coal and low NOx emission. The present study provides helpful information for understanding and optimizing the combustion of the studied boiler

scholarly journals Heat Scanning for the Fabrication of Conductive Fibers

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1405
Author(s):  
Jina Jang ◽  
Haoyu Zhou ◽  
Jungbae Lee ◽  
Hakgae Kim ◽  
Jung Bin In
Keyword(s):  
Silver Nanowires ◽  
Building Blocks ◽  
Dip Coating ◽  
Coating Materials ◽  
Scanning Time ◽  
Silver Ink ◽  
Nylon Fiber ◽  
Coating Method ◽  
Conductive Fibers ◽  
Tubular Heater

Conductive fibers are essential building blocks for implementing various functionalities in a textile platform that is highly conformable to mechanical deformation. In this study, two major techniques were developed to fabricate silver-deposited conductive fibers. First, a droplet-coating method was adopted to coat a nylon fiber with silver nanoparticles (AgNPs) and silver nanowires (AgNWs). While conventional dip coating uses a large ink pool and thus wastes coating materials, droplet-coating uses minimal quantities of silver ink by translating a small ink droplet along the nylon fiber. Secondly, the silver-deposited fiber was annealed by similarly translating a tubular heater along the fiber to induce sintering of the AgNPs and AgNWs. This heat-scanning motion avoids excessive heating and subsequent thermal damage to the nylon fiber. The effects of heat-scanning time and heater power on the fiber conductance were systematically investigated. A conductive fiber with a resistance as low as ~2.8 Ω/cm (0.25 Ω/sq) can be produced. Finally, it was demonstrated that the conductive fibers can be applied in force sensors and flexible interconnectors.

scholarly journals Influence of center gas supply device on gas–solid flow in COREX shaft furnace through DEM–CFD model

2020 ◽  
Vol 18 (5-6) ◽  
Author(s):  
Heng Zhou ◽  
Shuyu Wang ◽  
Binbin Du ◽  
Mingyin Kou ◽  
Zhiyong Tang ◽  
...  
Keyword(s):  
Gas Flow ◽  
Shaft Furnace ◽  
Middle Zone ◽  
Cfd Model ◽  
Gas Velocity ◽  
Gas Distribution ◽  
Particle Segregation ◽  
Solid Flow ◽  
Corex Shaft Furnace ◽  
Gas Supply

AbstractIn order to develop the central gas flow in COREX shaft furnace, a new installment of center gas supply device (CGD) is designed. In this work, a coupled DEM–CFD model was employed to study the influence of CGD on gas–solid flow in COREX shaft furnace. The particle descending velocity, particle segregation behaviour, void distribution and gas distribution were investigated. The results show that the CGD affects the particles descending velocity remarkably as the burden falling down to the slot. Particle segregation can be observed under the inverse ‘V’ burden profile, and the influence of CGD on the particle segregation is unobvious on the whole, which causes the result that the voidage is slightly changed. Although the effect of CGD on solid flow is not significant, the gas flow in shaft furnace has an obvious change. Compared with the condition without CGD, in the case with CGD, the gas velocity is improved significantly, especially in the middle zone of the furnace, which further promotes the center gas distribution. Meanwhile, the pressure drop in the furnace with the installation of CGD is increased partly.

Sign in / Sign up

Export Citation Format

Share Document