Numerical study of three dimensional acoustic resonances in open cavities at high Reynolds numbers

2015 ◽  
Vol 45 ◽  
pp. 501-511 ◽  
Author(s):  
M. Kompenhans ◽  
E. Ferrer ◽  
M. Chavez ◽  
E. Valero
Keyword(s):  
Numerical Study ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
High Reynolds Numbers ◽  
Open Cavities ◽  
Acoustic Resonances ◽  
High Reynolds

An Experimental and Numerical Study of Heat Transfer and Pressure Loss in a Rectangular Channel With V-Shaped Ribs

2006 ◽  
Author(s):  
Michael Maurer ◽  
Jens von Wolfersdorf ◽  
Michael Gritsch
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Thermal Performance ◽  
Pressure Loss ◽  
Numerical Study ◽  
Rectangular Channel ◽  
Reynolds Numbers ◽  
Transfer Enhancement ◽  
High Reynolds Numbers ◽  
High Reynolds

An experimental and numerical study was conducted to determine the thermal performance of V-shaped ribs in a rectangular channel with an aspect ratio of 2:1. Local heat transfer coefficients were measured using the steady state thermochromic liquid crystal technique. Periodic pressure losses were obtained with pressure taps along the smooth channel sidewall. Reynolds numbers from 95,000 to 500,000 were investigated with V-shaped ribs located on one side or on both sides of the test channel. The rib height-to-hydraulic diameter ratios (e/Dh) were 0.0625 and 0.02, and the rib pitch-to-height ratio (P/e) was 10. In addition, all test cases were investigated numerically. The commercial software FLUENT™ was used with a two-layer k-ε turbulence model. Numerically and experimentally obtained data were compared. It was determined that the heat transfer enhancement based on the heat transfer of a smooth wall levels off for Reynolds numbers over 200,000. The introduction of a second ribbed sidewall slightly increased the heat transfer enhancement whereas the pressure penalty was approximately doubled. Diminishing the rib height at high Reynolds numbers had the disadvantage of a slightly decreased heat transfer enhancement, but benefits in a significantly reduced pressure loss. At high Reynolds numbers small-scale ribs in a one-sided ribbed channel were shown to have the best thermal performance.

scholarly journals A numerical study of flow around an impulsively started circular cylinder by a deterministic vortex method

1991 ◽  
Vol 233 ◽  
pp. 243-263 ◽  
Author(s):  
Chien-Cheng Chang ◽  
Ruey-Ling Chern
Keyword(s):  
Finite Difference ◽  
Circular Cylinder ◽  
Numerical Study ◽  
Vortex Method ◽  
Reynolds Numbers ◽  
Numerical Results ◽  
High Reynolds Numbers ◽  
Small Times ◽  
Axis Of Symmetry ◽  
High Reynolds

Impulsively started flow around a circular cylinder at various Reynolds numbers is studied by a deterministic hybrid vortex method. The key feature of the method consists in solving the viscous vorticity equation by interlacing a finite-difference method for diffusion and a vortex-in-cell method for convection. The vorticity is updated along the surface of the cylinder to satisfy the no-slip condition. The present method is basically different from previous applications of vortex methods, which are primarily in the context of random vortex algorithms. The Reynolds numbers of the flows under investigation range from 300 to 106. Numerical results are compared with analytical solutions at small times, and compared with finite-difference solutions and flow visualization results at relatively long times. Satisfactory agreement is found in the evolutions of the separation angles, wake lengths, surface pressure and drag coefficients, streamline patterns, and some velocities on the axis of symmetry behind the circular cylinder. The present hybrid vortex method is highly stable and suffers from little numerical diffusivity, yielding convincing numerical results for unsteady vortical flows at moderately high Reynolds numbers.

New thermal-hydraulic correlations for printed circuit heat exchangers (PCHEs) with zigzag channels under high Reynolds numbers

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Carolina P. Naveira-Cotta ◽  
Jian Su ◽  
Paulo Lucena Kreppel Paes ◽  
Philippe R. Egmont ◽  
Rodrigo P. M. Moreira ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Design Parameters ◽  
Channel Diameter ◽  
Content Type ◽  
Printed Circuit ◽  
High Reynolds Numbers ◽  
High Reynolds ◽  
The Impact

Purpose The purpose of this paper is to investigate the impact of semi-circular zigzag-channel printed circuit heat exchanger (PCHE) design parameters on heat transfer and pressure drop of flows under high Reynolds numbers and provide new thermal-hydraulic correlations relevant to conditions encountered in natural gas processing plants. Design/methodology/approach The correlations were developed using three-dimensional steady-state computational fluid dynamics simulations with varying semicircular channel diameter (from 1 to 5 mm), zigzag angle (from 15° to 45°) and Reynolds number (from 40,000 to 100,000). The simulation results were validated by comparison with experimental results and existing correlations. Findings The results revealed that the thermal-hydraulic performance was mostly affected by the zigzag angle, followed by the ratio of the zigzag channel length to the hydraulic diameter. Overall, smaller zigzag angles favored heat transfer intensification while keeping reasonably low pressure drops. Originality/value This study is, to date, the only one providing thermal-hydraulic correlations for PCHEs with zigzag channels under high Reynolds numbers. Besides, the broad range of parameters considered makes the proposed correlations valuable PCHE design tools.

How Turbulence Models Perform in Simulating Pipeflow Response to Targeted Wall-Shapes?

2021 ◽  
Author(s):  
Mehran Masoumifar ◽  
Suyash Verma ◽  
Arman Hemmati
Keyword(s):  
Three Dimensional ◽  
Turbulence Models ◽  
Reynolds Numbers ◽  
Navier Stokes ◽  
Flow Response ◽  
High Reynolds Numbers ◽  
Flow Features ◽  
Rans Models ◽  
Response And Recovery ◽  
High Reynolds

Abstract This study evaluates how Reynolds-Averaged-Navier-Stokes (RANS) models perform in simulating the characteristics of mean three-dimensional perturbed flows in pipes with targeted wall-shapes. Capturing such flow features using turbulence models is still challenging at high Reynolds numbers. The principal objective of this investigation is to evaluate which of the well-established RANS models can best predict the flow response and recovery characteristics in perturbed pipes at moderate and high Reynolds numbers (10000-158000). First, the flow profiles at various axial locations are compared between simulations and experiments. This is followed by assessing the well-known mean pipeflow scaling relations. The good agreement between our computationally predicted data using Standard k-epsilon model and those of experiments indicated that this model can accurately capture the pipeflow characteristics in response to introduced perturbation with smooth sinusoidal axial variations.

Sign in / Sign up

Export Citation Format

Share Document