Effect of the thermal conductivity of building materials on the steady-state thermal behaviour of underground building envelopes

2006 ◽  
Vol 41 (3) ◽  
pp. 330-335 ◽  
Author(s):  
Yanping Yuan ◽  
Baoyi Cheng ◽  
Jinfeng Mao ◽  
Yanxia Du
Keyword(s):  
Thermal Conductivity ◽  
Steady State ◽  
Thermal Behaviour ◽  
Building Materials ◽  
Building Envelopes

scholarly journals Comparison of the thermal performance between conventional and cob building

2019 ◽  
Vol 111 ◽  
pp. 03003
Author(s):  
Kaoutar Zeghari ◽  
Hasna Louahlia ◽  
Malo Leguern ◽  
Mohamed Boutouil ◽  
Hamid Gualous ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Thermal Behaviour ◽  
Calculation Method ◽  
Building Materials ◽  
Residential Building ◽  
Local Heat ◽  
Energy Performance ◽  
Stationary Regime ◽  
Thermal Regulation ◽  
Climate Data

The appliance of sustainable development approach in building has urged construction industry to adopt proper measurements to protect environment and reduce residential building energy consumption and CO2 emissions. Thus, an increasing interest in alternative building materials has developed including the use of bio-based materials such as cob which is studied in this paper. In the previous work, many experimental and numerical studies have been carried out to characterize thermal behaviour of earth buildings, reduce its thermal conductivity and water content. In this paper, an experimental study is carried out to determine the thermal properties and energy performance of cob building. Cob samples within different soil and fiber contents are studied using an experimental set up instrumented with flux meters and micro-thermocouples in order to evaluate the local heat flux and thermal conductivity during stationary regime. The results are analysed and compared to deduce the performant mixes in terms of thermal behaviour while respecting the French thermal regulation. A static thermal simulation based on RT 2012 calculation method (the official French calculation method for the energy performance of new residential and commercial buildings according to France thermal regulation) is used to compare energy performance between conventional and cob building using the French climate data base .

scholarly journals Testing a Gypsum Composite Based on Raw Gypsum with a Direct Admixture of Paraffin and Polymer to Improve Thermal Properties

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3241
Author(s):  
Krzysztof Powała ◽  
Andrzej Obraniak ◽  
Dariusz Heim
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Thermal Properties ◽  
Phase Change ◽  
Large Scale ◽  
Building Materials ◽  
Residential Buildings ◽  
Energy Performance ◽  
Polymer Content ◽  
Volumetric Heat Capacity

The implemented new legal regulations regarding thermal comfort, the energy performance of residential buildings, and proecological requirements require the design of new building materials, the use of which will improve the thermal efficiency of newly built and renovated buildings. Therefore, many companies producing building materials strive to improve the properties of their products by reducing the weight of the materials, increasing their mechanical properties, and improving their insulating properties. Currently, there are solutions in phase-change materials (PCM) production technology, such as microencapsulation, but its application on a large scale is extremely costly. This paper presents a solution to the abovementioned problem through the creation and testing of a composite, i.e., a new mixture of gypsum, paraffin, and polymer, which can be used in the production of plasterboard. The presented solution uses a material (PCM) which improves the thermal properties of the composite by taking advantage of the phase-change phenomenon. The study analyzes the influence of polymer content in the total mass of a composite in relation to its thermal conductivity, volumetric heat capacity, and diffusivity. Based on the results contained in this article, the best solution appears to be a mixture with 0.1% polymer content. It is definitely visible in the tests which use drying, hardening time, and paraffin absorption. It differs slightly from the best result in the thermal conductivity test, while it is comparable in terms of volumetric heat capacity and differs slightly from the best result in the thermal diffusivity test.

scholarly journals Thermal conductivity of insulating refractory materials: comparison of steady-state and transient measurement methods

Open Ceramics ◽  
2021 ◽  
pp. 100118
Author(s):  
Diana Vitiello ◽  
Benoit Nait-Ali ◽  
Nicolas Tessier-Doyen ◽  
Thorsten Tonnesen ◽  
Luís Laím ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Steady State ◽  
Measurement Methods ◽  
Refractory Materials ◽  
Transient Measurement

Design of a Steady-State, Parallel-Plate Thermal Conductivity Apparatus for Nanofluids and Comparative Measurements With Transient HWTC Apparatus

2010 ◽  
Author(s):  
Milivoje M. Kostic ◽  
Casey J. Walleck
Keyword(s):  
Thermal Conductivity ◽  
Steady State ◽  
Parallel Plate ◽  
Measurement Method ◽  
Mixture Theory ◽  
Hot Wire ◽  
Electro Magnetic ◽  
Magnetic Phenomena ◽  
Thermal Conductivities

A steady-state, parallel-plate thermal conductivity (PPTC) apparatus has been developed and used for comparative measurements of complex POLY-nanofluids, in order to compare results with the corresponding measurements using the transient, hotwire thermal conductivity (HWTC) apparatus. The related measurements in the literature, mostly with HWTC method, have been inconsistent and with measured thermal conductivities far beyond prediction using the well-known mixture theory. The objective was to check out if existing and well-established HWTC method might have some unknown issues while measuring TC of complex nano-mixture suspensions, like electro-magnetic phenomena, undetectable hot-wire vibrations, and others. These initial and limited measurements have shown considerable difference between the two methods, where the TC enhancements measured with PPTC apparatus were about three times smaller than with HWTC apparatus, the former data being much closer to the mixture theory prediction. However, the influence of measurement method is not conclusive since it has been observed that the complex nano-mixture suspensions were very unstable during the lengthy steady-state measurements as compared to rather quick transient HWTC method. The nanofluid suspension instability might be the main reason for very inconsistent results in the literature. It is necessary to expend investigation with more stable nano-mixture suspensions.

Sign in / Sign up

Export Citation Format

Share Document