Numerical simulations study of the localized corrosion resistance of AISI 316L stainless steel and pure titanium in a simulated body fluid environment

2011 ◽  
Vol 53 (10) ◽  
pp. 3309-3314 ◽  
Author(s):  
K. Yaya ◽  
Y. Khelfaoui ◽  
B. Malki ◽  
M. Kerkar
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Simulated Body Fluid ◽  
Body Fluid ◽  
316L Stainless Steel ◽  
Pure Titanium ◽  
Localized Corrosion ◽  
Aisi 316L ◽  
Aisi 316L Stainless Steel ◽  
Fluid Environment

scholarly journals Corrosion study of metallic biomaterials in simulated body fluid

10.30544/384 ◽  
2011 ◽  
Vol 17 (1) ◽  
pp. 13-22 ◽  
Author(s):  
Hamid Reza Asgari Bidhendi ◽  
Majid Pouranvari
Keyword(s):  
Stainless Steel ◽  
Simulated Body Fluid ◽  
Corrosion Behavior ◽  
Body Fluid ◽  
Pure Titanium ◽  
Localized Corrosion ◽  
Commercially Pure Titanium ◽  
Corrosion Properties ◽  
Cyclic Polarization ◽  
Cp Ti

Titanium alloys and stainless steel 316L are still the most widely used biomaterials for implants despite emerging new materials for this application. There is still someambiguity in corrosion behavior of metals in simulated body fluid (SBF). This paper aims at investigating the corrosion behavior of commercially pure titanium (CP-Ti), Ti–6Al–4V and 316LVM stainless steel (316LVM) in SBF (Hank’s solution) at37 ºC using the cyclic polarization test. Corrosion behavior was described in terms of breakdown potential, the potential and rate ofcorrosion, localized corrosion resistance, andbreakdown repassivation. The effects of anodizing on CP-Ti samples and the passivation on the 316LVM were studied in detail. It was shown that CP-Ti exhibited superior corrosion properties compared to Ti–6Al–4V and 316LVM.

scholarly journals Corrosion Resistance of AISI 316L Stainless Steel Biomaterial after Plasma Immersion Ion Implantation of Nitrogen

Materials ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 6790
Author(s):  
Viera Zatkalíková ◽  
Juraj Halanda ◽  
Dušan Vaňa ◽  
Milan Uhríčik ◽  
Lenka Markovičová ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Ion Implantation ◽  
316L Stainless Steel ◽  
Electrochemical Impedance ◽  
Austenitic Stainless Steels ◽  
Aisi 316L ◽  
Corrosion Properties ◽  
Aisi 316L Stainless Steel ◽  
Plasma Immersion Ion Implantation

Plasma immersion ion implantation (PIII) of nitrogen is low-temperature surface technology which enables the improvement of tribological properties without a deterioration of the corrosion behavior of austenitic stainless steels. In this paper the corrosion properties of PIII-treated AISI 316L stainless steel surfaces are evaluated by electrochemical impedance spectroscopy (EIS), potentiodynamic polarization (PP) and exposure immersion tests (all carried out in the 0.9 wt. % NaCl solution at 37 ± 0.5 °C) and compared with a non-treated surface. Results of the three performed independent corrosion tests consistently confirmed a significant increase in the corrosion resistance after two doses of PIII nitriding.

scholarly journals Improving the Corrosion Resistance of AISI 316L Steel for Semiconductor Piping by Controlled Delta-Ferrite Content

2022 ◽  
Vol 60 (1) ◽  
pp. 46-52
Author(s):  
Young Woo Seo ◽  
Chan Yang Kim ◽  
Bo Kyung Seo ◽  
Won Sub Chung
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
316L Stainless Steel ◽  
Sem Analysis ◽  
Ferrite Content ◽  
Aisi 316L ◽  
Delta Ferrite ◽  
Aisi 316L Stainless Steel ◽  
316L Steel ◽  
The Difference

This study evaluated changes in delta-ferrite content depending on the preheating of AISI 316L stainless steel. We also determined the reasons for the variation in delta-ferrite content, which affects corrosion resistance. Changes in delta-ferrite content after preheating was confirmed using a Feritscope, and the microstructure was analyzed using optical microscopy (OM). We found that the delta-ferrite microstructure size decreased when preheating time was increased at 1295 oC, and that the delta-ferrite content could be controlled through preheating. Potentiodynamic polarization test were carried out in NaCl (0.5 M) + H2SO4 (0.5 M) solution, and it was found that higher delta-ferrite content resulted in less corrosion potential and passive potential. To determine the cause, an analysis was conducted using energy-dispersive spectroscopy (EDS), which confirmed that higher delta-ferrite content led to weaker corrosion resistance, due to Cr degradation at the delta-ferrite and austenite boundaries. The degradation of Cr on the boundaries between austenite and delta-ferrite can be explained by the difference in the diffusion coefficient of Cr in the ferrite and austenite. A scanning electron microscopy (SEM) analysis of material used for actual semiconductor piping confirmed that corrosion begins at the delta-ferrite and austenite boundaries. These results confirm the need to control delta-ferrite content in AISI 316L stainless steel used for semiconductor piping.

Adhesion and Corrosion of Ti, TiN and TiCrN Films Deposits on AISI 316L in SBF Solution

2019 ◽  
Vol 397 ◽  
pp. 39-50
Author(s):  
Djamel Amari ◽  
Hafit Khireddine ◽  
Youcef Khelfaoui ◽  
Nadia Saoula
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Critical Load ◽  
316L Stainless Steel ◽  
Electrochemical Performances ◽  
Aisi 316L ◽  
Aisi 316L Stainless Steel ◽  
Crack Propagation Resistance ◽  
High Adhesion ◽  
Sbf Solution

Abstract. In the present work several films of Ti, TiN, and TiCrN have been coated on AISI 316L stainless steel substrates using magnetron sputtering techniques, in order to improve their surface properties. The morphology and structure of the coatings were analysed using scanning electron microscopy (SEM) and X-ray diffraction (XRD). The electrochemical performances skills in an SBF solution and the adhesion of these deposits were studied to understand these behaviors. From the results it was shown the TiCrN deposition presents the lowest corrosion resistance in the SBF solution, while TiN deposit is the most resistant to corrosion resistance in the same solutions, but its critical load (Lc3-TiN), is relatively low and has a risk of delamination which can limit its use. On the other hand, the Ti deposit exhibits a high resistance to corrosion and a high passivation (icorr (Ti) = 0.57 µA.cm-2 and Rp (Ti) = 67.98 KW.cm2). The critical load (Lc3-Ti = 43.38 N), the crack propagation resistance (CPRs-Ti = 81.64 N) and the scratch hardness (HSL-Ti = 125.75´1012 Pa) also testify to its high adhesion to the AISI 316L substrate. Thus the Ti deposit has proved to be the most favorable protective coating for AISI 316L stainless steel in SBF solution.

Effect of Pre-Oxidation at 800 °C on the Pitting Corrosion Resistance of the AISI 316L Stainless Steel

2010 ◽  
Vol 75 (1-2) ◽  
pp. 27-39 ◽  
Author(s):  
H. Buscail ◽  
S. El Messki ◽  
F. Riffard ◽  
S. Perrier ◽  
C. Issartel
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Pitting Corrosion ◽  
316L Stainless Steel ◽  
Aisi 316L ◽  
Aisi 316L Stainless Steel ◽  
Pitting Corrosion Resistance
Sign in / Sign up

Export Citation Format

Share Document