scholarly journals Mathematical modelling of gasification process of sewage sludge in reactor of negative CO2 emission power plant

Energy ◽  
2021 ◽  
pp. 122601
Author(s):  
Paweł Ziółkowski ◽  
Janusz Badur ◽  
Halina Pawlak- Kruczek ◽  
Kamil Stasiak ◽  
Milad Amiri ◽  
...  
Energies ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 6304
Author(s):  
Paweł Ziółkowski ◽  
Paweł Madejski ◽  
Milad Amiri ◽  
Tomasz Kuś ◽  
Kamil Stasiak ◽  
...  

The article presents results of thermodynamic analysis using a zero-dimensional mathematical models of a negative CO2 emission power plant. The developed cycle of a negative CO2 emission power plant allows the production of electricity using gasified sewage sludge as a main fuel. The negative emission can be achieved by the use this type of fuel which is already a “zero-emissive” energy source. Together with carbon capture installation, there is a possibility to decrease CO2 emission below the “zero” level. Developed models of a novel gas cycle which use selected codes allow the prediction of basic parameters of thermodynamic cycles such as output power, efficiency, combustion composition, exhaust temperature, etc. The paper presents results of thermodynamic analysis of two novel cycles, called PDF0 and PFD1, by using different thermodynamic codes. A comparison of results obtained by three different codes offered the chance to verify results because the experimental data are currently not available. The comparison of predictions between three different software in the literature is something new, according to studies made by authors. For gross efficiency (54.74%, 55.18%, and 52.00%), there is a similar relationship for turbine power output (155.9 kW, 157.19 kW, and 148.16 kW). Additionally, the chemical energy rate of the fuel is taken into account, which ultimately results in higher efficiencies for flue gases with increased steam production. A similar trend is assessed for increased CO2 in the flue gas. The developed precise models are particularly important for a carbon capture and storage (CCS) energy system, where relatively new devices mutually cooperate and their thermodynamic parameters affect those devices. Proposed software employs extended a gas–steam turbine cycle to determine the effect of cycle into environment. First of all, it should be stated that there is a slight influence of the software used on the results obtained, but the basic tendencies are the same, which makes it possible to analyze various types of thermodynamic cycles. Secondly, the possibility of a negative CO2 emission power plant and the positive environmental impact of the proposed solution has been demonstrated, which is also a novelty in the area of thermodynamic cycles.


2006 ◽  
Vol 158 (1) ◽  
pp. 417-427 ◽  
Author(s):  
A. Verma ◽  
A.D. Rao ◽  
G.S. Samuelsen

2020 ◽  
Vol 143 (8) ◽  
Author(s):  
Siamak Hoseinzadeh ◽  
P. Stephan Heyns

Abstract In this article, energy, exergy, and environmental (3E) analysis of a 400 MW thermal power plant is investigated. First, the components of the power plant are examined in terms of energy consumption, and subsequently the energy losses, exergy destruction, and exergetic efficiency are obtained. It is shown that the highest energy losses are in the closed feedwater heaters Nos. 1 and 5 and the boiler with amounts of 7.6 × 10 J/s and 6.5 × 107 J/s, respectively. The highest exergy destruction occurs in the boiler and amounts to 4.13 × 108 J/s. The highest exergetic efficiency is 0.98 and is associated with the closed feedwater heaters Nos. 4 and 8. It is observed that the exergetic efficiency and exergy destruction in the boiler are the primarily affected by changes in the environmental temperature. Furthermore, by increasing the main pressure in the turbine, the load on the power plant is increased, and increasing the condenser pressure reduces the load on the power plant. In an environmental analysis, the production of pollutants such as SO2 production and CO2 emission has been investigated.


Author(s):  
M. A. J. van Berlo ◽  
Harry de Waart

A CO2-evaluation is made for landfill and Waste-to-Energy (WtE) concepts. Different concepts are identified and compared for their performance on energy and materials recovery. Performance indicators for WtE are compared; like energy efficiency, EXergy efficiency, the R1-D10 formula from the EU Waste Framework directive, and CO2-emission and avoidance. It is shown that, due to the biomass content and the avoidance effect due to the recovery of energy and materials, conventional WtE has a near zero CO2-emission per ton of waste. Optimised WtE can have a significant negative overall emission of 200–300 kgCO2/ton of waste. This means an absolute net avoidance of CO2 by WtE. The reduction relative to land filling is as much as 500–1200 kgCO2/ton of waste. The potential for optimisation of the energy recovery as well as the material recovery of the WtE infrastructure is demonstrated. If WtE is evaluated as a power plant, an optimised plant can have an emission of only 0,336 kgCO2/kWh, lower than a gas fired electrical power plant, and this absolute figure does not include the avoided landfill emissions. With CHP this can be reduced even further. The actual potential of electricity production from WtE for the EU-15 is calculated to be over 7,5% of total electricity production. Additionally heat and the metal recoveries could be doubled.


Sign in / Sign up

Export Citation Format

Share Document