Coal mining under difficult geological conditions: The Can lignite open pit (Canakkale, Turkey)

2012 ◽  
Vol 135-136 ◽  
pp. 66-82 ◽  
Author(s):  
A. Kayabasi ◽  
C. Gokceoglu
2020 ◽  
Vol 243 ◽  
pp. 293
Author(s):  
Roman Shishkov ◽  
Valerii Fedorin

The article considers one actual method for development coal deposits in the Kuzbass by open-underground mining. The scientific and practical advantages of the proposed method due to the use of common infrastructure of coal mine and a modular mine site (subsequently transformed into a mining and technological structure operating according to the mine – longwall scheme) are presented. Currently, a development strategy for Kuzbass until 2035 has been developed. As part of the strategy, a draft program for subsoil use is being formed in the coal industry department. The program should take into account all the positive and negative aspects associated with coal mining in cities and municipal areas and also their prospects. In the Kuznetsk coal basin, 42 mines and 52 opencast mines are mining, of which 12 enterprises use partially unified infrastructure. According to the results of open-underground mining work conducted by the laboratory of the Institute of Coal and Coal Chemistry of the Siberian Branch of the Russian Academy of Sciences (Institute of Coal SB RAS), the list of sites includes favorable mining and geological conditions with incidence angles of up to 18 degrees. As open-pit coal production increases, many sites encounter such a parameter as maximum allowable (boundary) strip ratio. At the stage of preparing the feasibility study for the development of a coal deposit, this coefficient is calculated first of all, since duration of enterprise’s work and its economic component depend on it. In order to increase parameters, it is necessary to carry out transition from open works to underground. As a result, coal mine will not work at a loss, providing production with an economically disadvantageous strip ratio.


2012 ◽  
Vol 57 (2) ◽  
pp. 363-373
Author(s):  
Jan Macuda

Abstract In Poland all lignite mines are dewatered with the use of large-diameter wells. Drilling of such wells is inefficient owing to the presence of loose Quaternary and Tertiary material and considerable dewatering of rock mass within the open pit area. Difficult geological conditions significantly elongate the time in which large-diameter dewatering wells are drilled, and various drilling complications and break-downs related to the caving may occur. Obtaining higher drilling rates in large-diameter wells can be achieved only when new cutter bits designs are worked out and rock drillability tests performed for optimum mechanical parameters of drilling technology. Those tests were performed for a bit ø 1.16 m in separated macroscopically homogeneous layers of similar drillability. Depending on the designed thickness of the drilled layer, there were determined measurement sections from 0.2 to 1.0 m long, and each of the sections was drilled at constant rotary speed and weight on bit values. Prior to drillability tests, accounting for the technical characteristic of the rig and strength of the string and the cutter bit, there were established limitations for mechanical parameters of drilling technology: P ∈ (Pmin; Pmax) n ∈ (nmin; nmax) where: Pmin; Pmax - lowest and highest values of weight on bit, nmin; nmax - lowest and highest values of rotary speed of bit, For finding the dependence of the rate of penetration on weight on bit and rotary speed of bit various regression models have been analyzed. The most satisfactory results were obtained for the exponential model illustrating the influence of weight on bit and rotary speed of bit on drilling rate. The regression coefficients and statistical parameters prove the good fit of the model to measurement data, presented in tables 4-6. The average drilling rate for a cutter bit with profiled wings has been described with the form: Vśr= Z ·Pa· nb where: Vśr- average drilling rate, Z - drillability coefficient, P - weight on bit, n - rotary speed of bit, a - coefficient of influence of weight on bit on drilling rate, b - coefficient of influence of rotary speed of bit on drilling rate. Industrial tests were performed for assessing the efficiency of drilling of large-diameter wells with a cutter bit having profiled wings ø 1.16 m according to elaborated model of average rate of drilling. The obtained values of average rate of drilling during industrial tests ranged from 8.33×10-4 to 1.94×10-3 m/s and were higher than the ones obtained so far, i.e. from 181.21 to 262.11%.


Land ◽  
2021 ◽  
Vol 10 (6) ◽  
pp. 658
Author(s):  
Pratiwi ◽  
Budi H. Narendra ◽  
Chairil A. Siregar ◽  
Maman Turjaman ◽  
Asep Hidayat ◽  
...  

Tropical forests are among the most diverse ecosystems in the world, completed by huge biodiversity. An expansion in natural resource extraction through open-pit mining activities leads to increasing land and tropical forest degradation. Proper science-based practices are needed as an effort to reclaim their function. This paper summarizes the existing practice of coal mining, covering the regulatory aspects and their reclamation obligations, the practices of coal mining from various sites with different land characteristics, and the reclamation efforts of the post-mining landscapes in Indonesia. The regulations issued accommodate the difference between mining land inside the forest area and outside the forest area, especially in the aspect of the permit authority and in evaluating the success rate of reclamation. In coal-mining practices, this paper describes starting from land clearing activities and followed by storing soil layers and overburden materials. In this step, proper handling of potentially acid-forming materials is crucial to prevent acid mine drainage. At the reclamation stage, this paper sequentially presents research results and the field applications in rearranging the overburden and soil materials, controlling acid mine drainage and erosion, and managing the drainage system, settling ponds, and pit lakes. Many efforts to reclaim post-coal-mining lands and their success rate have been reported and highlighted. Several success stories describe that post-coal-mining lands can be returned to forests that provide ecosystem services and goods. A set of science-based best management practices for post-coal-mine reforestation is needed to develop to promote the success of forest reclamation and restoration in post-coal-mining lands through the planting of high-value hardwood trees, increasing trees’ survival rates and growth, and accelerating the establishment of forest habitat through the application of proper tree planting technique. The monitoring and evaluation aspect is also crucial, as corrective action may be taken considering the different success rates for different site characteristics.


2018 ◽  
Vol 41 ◽  
pp. 01007
Author(s):  
Yuriy Kutepov ◽  
Aleksandr Mironov ◽  
Maksim Sablin ◽  
Elena Borger

This article considers mining and geological conditions of the site “Blagodatny” of the mine named after A.D. Ruban located underneaththe old open pit coal mine and the hydraulic-mine dump. The potentially dangerous zones in the undermined rock mass have been identified based onthe conditions of formation of water inflow into mine workings. Safe depthof coal seams mining has been calculated depending on the type of water body – the hydraulic-mine dump.


2021 ◽  
Vol 303 ◽  
pp. 01029
Author(s):  
Alexander Katsubin ◽  
Victor Martyanov ◽  
Milan Grohol

Information about the geological structure of Kuznetsky coal basin (Kuzbass) allows us to note that coal deposits developed by open-cast method are characterized by complicated conditions and have the following features: large length of deposits at significant depths of occurrence; coal series bedding of different thicknesses (from 1 to 40 m); different dip angles (from 3 to 90º); a significant number of dip and direction disturbances; different thickness of unconsolidated quaternary sediments (from 5 to 40 m); a wide range of strength values of rocks. In addition, there is a thickness irregularity and frequent variability of elements of occurrence of coal seams within the boundaries of a quarry field both in length and depth of mining. From the point of view of open-pit mining, such deposits are complex-structured. The factors listed above have a decisive influence on the choice of technical means, the order of development and the possibility of carrying out surface mining operations. Therefore, there is a need for a systematization of mining and geological conditions for the development of coal deposits, the purpose of which is to ensure a process of evaluation of complex-structured coal deposits for the development of coal-bearing zones by various complexes of equipment.


Industry 4.0 ◽  
2021 ◽  
pp. 235-248
Author(s):  
Victor I. Efimov ◽  
Natalia V. Efimova

Sign in / Sign up

Export Citation Format

Share Document