Long-term no tillage management impact on soil hydro-physical properties in coffee cultivation

Geoderma ◽  
2021 ◽  
Vol 404 ◽  
pp. 115306
Author(s):  
Ayodele Ebenezer Ajayi ◽  
Diego Tassinari ◽  
Cezar Francisco Araujo-Junior ◽  
Oluwaseun Temitope Faloye ◽  
Fashina Abayomi ◽  
...  
2009 ◽  
Vol 103 (1) ◽  
pp. 158-164 ◽  
Author(s):  
Karina Maria Vieira Cavalieri ◽  
Alvaro Pires da Silva ◽  
Cassio Antonio Tormena ◽  
Tairone Paiva Leão ◽  
Anthony R. Dexter ◽  
...  

Agronomy ◽  
2019 ◽  
Vol 9 (11) ◽  
pp. 750 ◽  
Author(s):  
Ripendra Awal ◽  
Mohammad Safeeq ◽  
Farhat Abbas ◽  
Samira Fares ◽  
Sanjit K. Deb ◽  
...  

Spatial variability of soil physical and hydrological properties within or among agricultural fields could be intrinsically induced due to geologic and pedologic soil forming factors, but some of the variability may be induced by anthropogenic activities such as tillage practices. No-tillage has been gaining ground as a successful conservation practice, and quantifying spatial variability of soil physical properties induced by no-tillage practices is a prerequisite for making appropriate site-specific agricultural management decisions and/or reformulating some management practices. In particular, there remains very limited information on the spatial variability of soil physical properties under long-term no-tillage corn and tropical soil conditions. Therefore, the main objective of this study was to quantify the spatial variability of some selected soil physical properties (soil surface temperature (ST), volumetric water content (θv), soil resistance (TIP), total porosity (θt), bulk density (ρb), organic carbon, and saturated hydraulic conductivity (Ksat)) using classical and geostatistical methods. The study site was a 2 ha field cropped no-tillage sweet corn for nearly 10 years on Oahu, Hawaii. The field was divided into 10 × 10 and 20 × 20 m grids. Soil samples were collected at each grid for measuring ρb, θt, and soil organic carbon (SOC) in the laboratory following standard methods. Saturated hydraulic conductivity, TIP at 10 and 20 cm depths, soil surface temperature, and θv were also measured. Porosity and ρb have low and low to moderate variability, respectively based on the relative ranking of the magnitude of variability drawn from the coefficient of variation. Variability of the SOC, TIP, and Ksat ranges from moderate to high. Based on the best-fitted semivariogram model for finer grid data, 9.8 m and 142.2 m are the cut off beyond which the measured parameter does not show any spatial correlation for SOC, and TIP at 10 cm depth, respectively. Bulk density shows the highest spatial dependence (range = 226.8 m) among all measured properties. Spatial distribution of the soil properties based on kriging shows a high level of variability even though the sampled field is relatively small.


2016 ◽  
Vol 160 ◽  
pp. 53-64 ◽  
Author(s):  
Wagner Henrique Moreira ◽  
Cássio Antonio Tormena ◽  
Douglas L. Karlen ◽  
Álvaro Pires da Silva ◽  
Thomas Keller ◽  
...  

2018 ◽  
Vol 10 (12) ◽  
pp. 4696 ◽  
Author(s):  
Amin Nouri ◽  
Jaehoon Lee ◽  
Xinhua Yin ◽  
Donald D. Tyler ◽  
Sindhu Jagadamma ◽  
...  

A better understanding of the effect of long-term tillage management on soil properties and yield is essential for sustainable food production. This research aimed to evaluate the 37-year impact of different tillage systems and cover cropping on soil hydro-physical properties at 0–15 and 15–30 cm, as well as on soybean [Glycine max (L.) Merr] yield. The long-term experiment was located in Jackson, TN, and the different treatments involved in this study were no-tillage (NT), disk (DP), chisel (CP), moldboard plow (MP), and no-tillage with winter wheat [Triticum aestivum (L.)] cover crop (NTW). Forty-five days after the tillage operation, MP showed a comparable bulk density (BD) with NT, NTW, and CP at 0–15 cm depth. At surface depth, No-tillage systems increased cone penetration resistance (PR) by 12% compared with the reduced tillage systems, and 47% relative to MP. Wet aggregate stability (WAS) at surface depth was 27% and 36% greater for NT systems than for reduced and conventional tillage systems, respectively. Similarly, the geometric mean diameter (GMD) of aggregates was significantly higher under NT and NTW. However, water infiltration and field-saturated hydraulic conductivity (Kfs) did not differ significantly among tillage systems. The greatest soybean yield was obtained from CP and DP, producing 10% higher yield than NTW. Overall, 37 years of no-tillage, with or without simplified cover cropping did not result in a consistent improvement in soybean yield and soil physical properties with the exception of having improved soil aggregation.


Alloy Digest ◽  
2010 ◽  
Vol 59 (1) ◽  

Abstract Kubota KNC-03 is a grade with a combination of high strength and excellent resistance to oxidation. These properties make this alloy suitable for long-term service at temperature up to 1250 deg C (2282 deg F). This datasheet provides information on physical properties, hardness, elasticity, tensile properties, and compressive strength as well as creep. It also includes information on high temperature performance as well as casting and joining. Filing Code: Ni-676. Producer or source: Kubota Metal Corporation, Fahramet Division. See also Alloy Digest Ni-662, April 2008.


Alloy Digest ◽  
2011 ◽  
Vol 60 (12) ◽  

Abstract Kubota Alloy HD (UNS J93005) is a heat-resisting stainless steel casting alloy suitable for long-term service at temperatures up to 1095 deg C (2000 deg F). The nearest wrought equivalent is type 327. This datasheet provides information on composition, physical properties, hardness, and tensile properties as well as creep. It also includes information on corrosion resistance as well as casting and joining. Filing Code: SS-1110. Producer or source: Kubota Metal Corporation, Fahramet Division.


Alloy Digest ◽  
2010 ◽  
Vol 59 (5) ◽  

Abstract Kubota Alloy HC is a heat resisting stainless steel casting suitable for long term service at temperatures up to 1093 deg C (2000 deg F). This alloy can maintain resistance to sulfur bearing environments up to 1093 deg C (2000 deg F). This datasheet provides information on composition, physical properties, hardness, and tensile properties. It also includes information on corrosion resistance as well as casting and joining. Filing Code: SS-1065. Producer or source: Kubota Metal Corporation, Fahramet Division.


Sign in / Sign up

Export Citation Format

Share Document