The rise time of the change of cometary brightness during its outburst

Icarus ◽  
2021 ◽  
pp. 114847
Author(s):  
Wesołowski Marcin
Keyword(s):  
2020 ◽  
Vol 7 (2) ◽  
pp. 127-134
Author(s):  
Safah Tasya Aprilyani ◽  
Irianto Irianto ◽  
Epyk Sunarno

Penggunaan kontrol sangat diperlukan dalam pengaturan kecepatan motor DC. Dalam pengaturan kecepatan motor DC, salah satu jenis kontrol yang digunakan adalah kontrol Proportional Integral (PI). Untuk 4 jenis metode pada kontrol PI yang digunakan adalah metode Ziegler Nichole, Chien Servo 1, Chien Regulator 1 dan perhitungan secara analitik yang telah diperoleh dari data yang sudah ada.  Namun kontrol dengan PI 4 metode yang digunakan  sebagai pembanding memiliki waktu respon kecepatan saat stabil cenderung lambat baik dari nilai settling time, rise time dan steady state. Maka dari itu dilakukan komparasi antara 4 metode kontrol PI dengan penggunaan kontrol fuzzy. Dalam membandingkan antara 4 metode kontrol PI dan kontrol fuzzy terdapat beberapa parameter sebagai perbandingan yaitu maximum overshoot, steady state, rise time dan settling time. Hasil dari perbandingan tersebut adalah kontrol fuzzy dapat menghasilkan performa lebih baik jika dibandingkan dengan 4 metode pada kontrol PI. Kontrol fuzzy memiliki nilai rise time sebesar 0,015 detik, nilai settling time sebesar 0,025 detik dengan kecepatan sebesar 2900 rpm serta error steady state sebesar 3,33% tanpa adanya overshoot dan osilasi.


JURNAL ELTEK ◽  
2018 ◽  
Vol 16 (2) ◽  
pp. 125
Author(s):  
Oktriza Melfazen

Buck converter idealnya mempunyai keluaran yang stabil, pemanfaatandaya rendah, mudah untuk diatur, antarmuka yang mudah dengan pirantiyang lain, ketahanan yang lebih tinggi terhadap perubahan kondisi alam.Beberapa teknik dikembangkan untuk memenuhi parameter buckconverter. Solusi paling logis untuk digunakan pada sistem ini adalahmetode kontrol digital.Penelitian ini menelaah uji performansi terhadap stabilitas tegangankeluaran buck converter yang dikontrol dengan Logika Fuzzy metodeMamdani. Rangkaian sistem terdiri dari sumber tegangan DC variable,sensor tegangan dan Buck Converter dengan beban resistif sebagaimasukan, mikrokontroler ATMega 8535 sebagai subsistem kontroldengan metode logika fuzzy dan LCD sebagai penampil keluaran.Dengan fungsi keanggotaan error, delta error dan keanggotaan keluaranmasing-masing sebanyak 5 bagian serta metode defuzzifikasi center ofgrafity (COG), didapat hasil rerata error 0,29% pada variable masukan18V–20V dan setpoint keluaran 15V, rise time (tr) = 0,14s ; settling time(ts) = 3,4s ; maximum over shoot (%OS) = 2,6 dan error steady state(ess) = 0,3.


2012 ◽  
Vol 132 (10) ◽  
pp. 838-843 ◽  
Author(s):  
Nobuaki Kikuchi ◽  
Yoshihiro Suyama ◽  
Satoshi Okamoto ◽  
Osamu Kitakami

Author(s):  
Junji Maeda ◽  
Takashi Takeuchi ◽  
Eriko Tomokiyo ◽  
Yukio Tamura

To quantitatively investigate a gusty wind from the viewpoint of aerodynamic forces, a wind tunnel that can control the rise time of a step-function-like gust was devised and utilized. When the non-dimensional rise time, which is calculated using the rise time of the gusty wind, the wind speed, and the size of an object, is less than a certain value, the wind force is greater than under the corresponding steady wind. Therefore, this wind force is called the “overshoot wind force” for objects the size of orbital vehicles in an actual wind observation. The finding of the overshoot wind force requires a condition of the wind speed recording specification and depends on the object size and the gusty wind speed.


2016 ◽  
Vol 30 (06) ◽  
pp. 1650063 ◽  
Author(s):  
Jingwen Sun ◽  
Jian Sun ◽  
Yunji Yi ◽  
Lucheng Qv ◽  
Shiqi Sun ◽  
...  

A low-cost and high-speed electro-optic (EO) switch using the guest–host EO material Disperse Red 1/Polymethyl Methacrylate (DR1/PMMA) was designed and fabricated. The DR1/PMMA material presented a low processing cost, an excellent photostability and a large EO coefficient of 13.1 pm/V. To improve the performance of the switch, the in-plane buried electrode structure was introduced in the polymer Mach–Zehnder waveguide to improve the poling and modulating efficiency. The characteristic parameters of the waveguide and the electrodes were carefully designed and the fabrication process was strictly controlled. Under 1550 nm, the insertion loss of the device was 12.7 dB. The measured switching rise time and fall time of the switch were 50.00 ns and 54.29 ns, respectively.


2021 ◽  
Vol 1826 (1) ◽  
pp. 012103
Author(s):  
Pedro Oliveira Costa Machado Neto ◽  
Paulo Cesar Ramalho Brandão ◽  
Juan Carlos Mateus Sanchez ◽  
Lúnia Coelho de Almeida de Lima ◽  
Carlos Eduardo Cardoso Galhardo

1991 ◽  
Author(s):  
Fred J. Zutavern ◽  
Guillermo M. Loubriel ◽  
Marty W. O'Malley ◽  
Dan L. McLaughlin ◽  
Wesley D. Helgeson

Sign in / Sign up

Export Citation Format

Share Document