scholarly journals Simple shear behavior and constitutive modeling of 304 stainless steel over a wide range of strain rates and temperatures

2021 ◽  
Vol 154 ◽  
pp. 103896
Author(s):  
B. Jia ◽  
A. Rusinek ◽  
R. Pesci ◽  
R. Bernier ◽  
S. Bahi ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Simple Shear ◽  
Constitutive Modeling ◽  
Shear Behavior ◽  
304 Stainless Steel ◽  
Strain Rates ◽  
Wide Range

Comparison of Recovery and Recrystallization in Stainless Steel Following Plane-Wave Shock Loading and Explosive Forming

1970 ◽  
Vol 28 ◽  
pp. 428-429 ◽  
Author(s):  
J. A. Korbonski ◽  
L. E. Murr
Keyword(s):  
Stainless Steel ◽  
Shock Loading ◽  
Pressure Pulse ◽  
Shock Pressure ◽  
304 Stainless Steel ◽  
Strain Rates ◽  
Two Dimensional ◽  
Aisi 304 Stainless Steel ◽  
Aisi 304 ◽  
Explosive Forming

Comparison of recovery rates in materials deformed by a unidimensional and two dimensional strains at strain rates in excess of 104 sec.−1 was performed on AISI 304 Stainless Steel. A number of unidirectionally strained foil samples were deformed by shock waves at graduated pressure levels as described by Murr and Grace. The two dimensionally strained foil samples were obtained from radially expanded cylinders by a constant shock pressure pulse and graduated strain as described by Foitz, et al.

Evolution of microstructure of 304 stainless steel joined by brazing process

2010 ◽  
Vol 1276 ◽  
Author(s):  
F. García-Vázquez ◽  
I. Guzmán-Flores ◽  
A. Garza ◽  
J. Acevedo
Keyword(s):  
Tensile Strength ◽  
Stainless Steel ◽  
Holding Time ◽  
304 Stainless Steel ◽  
Commercial Application ◽  
Wide Range ◽  
Unique Method ◽  
Brazed Joints ◽  
Brazed Joint ◽  
Evolution Of Microstructure

AbstractBrazing is a unique method to permanently join a wide range of materials without oxidation. It has wide commercial application in fabricating components. This paper discusses results regarding the brazing process of 304 stainless steel. The experimental brazing is carried out using a nickel-based (Ni-11Cr-3.5Si-2.25B-3.5Fe) filler alloy. In this process, boron and silicon are incorporated to reduce the melting point, however they form hard and brittle intermetallic compounds with nickel (eutectic phases) which are detrimental to the mechanical properties of brazed joints. This investigation deals with the effects of holding time and brazing temperature on the microstructure of joint and base metal, intermetallic phases formation within the brazed joint as well as measurement of the tensile strength. The results show that a maximum tensile strength of 464 MPa is obtained at 1120°C and 4 h holding time. The shortest holding times will make boron diffuse insufficiently and generate a great deal of brittle boride components.

Constitutive modeling of polycarbonate over a wide range of strain rates and temperatures

2016 ◽  
Vol 21 (1) ◽  
pp. 97-117 ◽  
Author(s):  
Haitao Wang ◽  
Huamin Zhou ◽  
Zhigao Huang ◽  
Yun Zhang ◽  
Xiaoxuan Zhao
Keyword(s):  
Constitutive Modeling ◽  
Strain Rates ◽  
Wide Range

Wear and Friction of Nitrogen Ion Implanted Steel

1983 ◽  
Vol 105 (2) ◽  
pp. 239-244 ◽  
Author(s):  
J. A. Kirk ◽  
G. W. Egerton ◽  
B. D. Sartwell
Keyword(s):  
Stainless Steel ◽  
Ion Implantation ◽  
Wear Behavior ◽  
304 Stainless Steel ◽  
Nitrogen Ion Implantation ◽  
Wide Range ◽  
Wear And Friction ◽  
Nitrogen Ion ◽  
Contact Pressures ◽  
Ion Implanted

A pin on disk wear test apparatus was used to evaluate wear and friction properties for nitrogen ion implanted and non-ion implanted steel disks in the presence of a lubricant. Both AISI/1018 mild steel and 304 stainless steel were examined. Typical fluence levels for ion implantation were above 1017 ions/cm2. In this paper disk wear is measured directly by a Talysurf profilometer tracing of the disk wear scar. By varying the contact area of the pin it was possible to evaluate wear behavior of both unimplanted and implanted disks over a wide range of contact pressures. It is shown that stainless steel disk wear can be decreased by nitrogen ion implantation, provided that contact pressures remain less than the yield strength of the substrate material. No significant wear improvements were observed for 1018 steel. To evaluate improvements in hardness due to nitrogen ion implantation, very low penetration depth microhardness measurements were made and the indentation diagonals were measured in a scanning electron microscope. These results and their limitations are also presented.

High Strain-Rate Compressive Behavior and Constitutive Modeling of Selected Polymers Using Modified Ramberg-Osgood Equation

2014 ◽  
Vol 566 ◽  
pp. 80-85
Author(s):  
Kenji Nakai ◽  
Takashi Yokoyama
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
Compressive Stress ◽  
Constitutive Modeling ◽  
High Strain ◽  
Strain Rates ◽  
Stress Strain ◽  
Strain Behavior ◽  
Least Squares Fit ◽  
Wide Range

The present paper is concerned with constitutive modeling of the compressive stress-strain behavior of selected polymers at strain rates from 10-3 to 103/s using a modified Ramberg-Osgood equation. High strain-rate compressive stress-strain curves up to strains of nearly 0.08 for four different commercially available extruded polymers were determined on the standard split Hopkinson pressure bar (SHPB). The low and intermediate strain-rate compressive stress-strain relations were measured in an Instron testing machine. Six parameters in the modified Ramberg-Osgood equation were determined by fitting to the experimental stress-strain data using a least-squares fit. It was shown that the monotonic compressive stress-strain behavior over a wide range of strain rates can successfully be described by the modified Ramberg-Osgood constitutive model. The limitations of the model were discussed.

Sign in / Sign up

Export Citation Format

Share Document