scholarly journals Experimental study of submerged hydraulic jumps generated downstream of rectangular plunging jets

2021 ◽  
Vol 137 ◽  
pp. 103579
Author(s):  
José M. Carrillo ◽  
Francisca Marco ◽  
Luis G. Castillo ◽  
Juan T. García
2020 ◽  
Vol 55 (4) ◽  
pp. 477-487
Author(s):  
A. Asadi ◽  
S. M. Malek Jafarian ◽  
A. R. Teymourtash

Author(s):  
N.G.P.B. Neluwala ◽  
K.T.S. Karunanayake ◽  
K.B.G.M. Sandaruwan ◽  
K.P.P. Pathirana

2019 ◽  
Vol 81 (6) ◽  
Author(s):  
Djoko Legono ◽  
Roby Hambali ◽  
Denik Sri Krisnayanti

The utilization of the side channel spillway as the primary component of dam is generally due to the limitation of the available space to construct conventional spillway with design discharge capacity. Some impacts may only be identified through the hydraulic physical model study; these include the presence of the chaotic jumps at the downstream of the spillway crest, the cross flow on the steep channel, as well as the performance of the energy dissipation in the stilling basin. This paper presents the result of the experimental study of three-dimensional behaviour of flow over the entire components of the side channel spillway of Bener Dam, Indonesia. The main dam and its appurtenant components, i.e., the reservoir, the spillway crest, the spillway channel, and the energy dissipaters were built, and various discharges were introduced to study the hydraulic performance of the spillway crest, the stilling basin, the chute, and the energy dissipater. The observed data were collected and then analysed. The results show that firstly, some chaotic hydraulic jumps were found at the stilling basin at downstream spillway crest. These chaotic hydraulic jumps would produce significant vibration that may endanger the nearby structures.  Secondly, the presence of the cross flow along the steep channel downstream of the stilling basin may also need to be eliminated in such that its impact on the rise of water surface level does not create any objection. This may be carried out through the installation of baffles along the spillway channel bed. Thirdly, the presence of the hydraulic jumps at the energy dissipater basin under the design discharge has proven that the energy dissipater has performed well where local scour around the downstream structure was found to be not significant. However, to anticipate the raising of the water surface elevation at the energy dissipater basin, increasing the elevation of energy dissipater wall from +212.50 m to +215.00 m is highly recommended.


1996 ◽  
Vol 228 (1-2) ◽  
pp. 1-10 ◽  
Author(s):  
Tomas Bohr ◽  
Clive Ellegaard ◽  
Adam Espe Hansen ◽  
Anders Haaning

Author(s):  
Norio Baba ◽  
Norihiko Ichise ◽  
Syunya Watanabe

The tilted beam illumination method is used to improve the resolution comparing with the axial illumination mode. Using this advantage, a restoration method of several tilted beam images covering the full azimuthal range was proposed by Saxton, and experimentally examined. To make this technique more reliable it seems that some practical problems still remain. In this report the restoration was attempted and the problems were considered. In our study, four problems were pointed out for the experiment of the restoration. (1) Accurate beam tilt adjustment to fit the incident beam to the coma-free axis for the symmetrical beam tilting over the full azimuthal range. (2) Accurate measurements of the optical parameters which are necessary to design the restoration filter. Even if the spherical aberration coefficient Cs is known with accuracy and the axial astigmatism is sufficiently compensated, at least the defocus value must be measured. (3) Accurate alignment of the tilt-azimuth series images.


Sign in / Sign up

Export Citation Format

Share Document