Balance of mechanical properties of Mg-8Li-3Al-2Zn-0.5Y alloy by solution and low-temperature aging treatment

2019 ◽  
Vol 791 ◽  
pp. 655-664 ◽  
Author(s):  
Hao Ji ◽  
Xiang Peng ◽  
Xiaolong Zhang ◽  
Wencai Liu ◽  
Guohua Wu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Low Temperature ◽  
Aging Treatment ◽  
Low Temperature Aging ◽  
Temperature Aging

CAD/CAM Zirconia for Dental Application

2013 ◽  
Vol 320 ◽  
pp. 505-511
Author(s):  
Ning Li ◽  
Zhi Kai Wu ◽  
Chao Jian ◽  
Wan Qian Zhao ◽  
Jia Zhen Yan
Keyword(s):  
Mechanical Properties ◽  
Low Temperature ◽  
Key Words ◽  
20Th Century ◽  
Dental Materials ◽  
Tetragonal Zirconia ◽  
Dental Application ◽  
Cad Cam ◽  
Low Temperature Aging ◽  
Temperature Aging

During the 20th century, both dental materials and dental technologies for the fabrication of dental prosthesis progressed remarkably. Owing to the increased demand of safety and aesthetics, 3 mol% yttria stabilized tetragonal zirconia polycrystalline has been recently introduced in prosthetic dentistry for the fabrication of crowns and fixed partial dentures, in combination with CAD/CAM technique. This greatly changed the conventional dental laboratory work which is labor-intensive and experience-dependent. This review mainly introduced the state of dental zirconia and the application of CAD/CAM technology in dentistry. Key words: Dental Zirconia; CAD/CAM Technique; Mechanical Properties; Transformation Toughing; Low Temperature Aging;

Mechanical properties and low-temperature aging of tetragonal zirconia polycrystals processed by hot isostatic pressing

2003 ◽  
Vol 18 (10) ◽  
pp. 2415-2426 ◽  
Author(s):  
J. Muñoz-Saldaña ◽  
H. Balmori-Ramírez ◽  
D. Jaramillo-Vigueras ◽  
T. Iga ◽  
G. A. Schneider
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Low Temperature ◽  
Hot Isostatic Pressing ◽  
Tetragonal Zirconia ◽  
Hot Water ◽  
Full Density ◽  
Isostatic Pressing ◽  
Low Temperature Aging ◽  
Temperature Aging

The influence of grain size and density of yttria-tetragonal zirconia polycrystals (Y-TZPs) ceramics on mechanical properties and on low-temperature aging degradation (LTD) in air and in hot water was investigated. A TZP powder containing 3 mol% Y2O3 was consolidated by slip casting and densified by the sintering/hot isostatic pressing (HIP) method. Only the presintered samples that contained less than 0.15% open porosity reached near full density after HIP. The best conditions to reach full density were found to be attained by presintering and HIP both at 1400 °C. At these conditions, some of the best mechanical properties such as modulus of rupture and Weibull modulus reached 1397 ± 153 MPa and, 10.6, respectively. These values were clearly higher than those obtained from sintered bodies and samples hot isostatically pressed at 1600 °C. Aging degradation of 3Y-TZP materials can be avoided through microstructural design. Fully dense materials with a critical grain size <0.36 μm did not show any evidence of degradation after extreme aging conditions at pressurized autoclaving in hot water at 100, 200, and 260 °C for 8 h. We propose a criterion to predict degradation in air as well as in hot water for the characterized materials based on the microstructure and density control of the samples.

scholarly journals A Novel Design to Enhance the Mechanical Properties in Cu-Bearing Antibacterial Stainless Steel

Materials ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 403
Author(s):  
Shaoheng Sun ◽  
Zhiyong Xue ◽  
Licong An ◽  
Xiaohua Chen ◽  
Yifei Liu
Keyword(s):  
Stainless Steel ◽  
Low Temperature ◽  
Antibacterial Properties ◽  
Aging Treatment ◽  
Copper Precipitation ◽  
The Matrix ◽  
Novel Method ◽  
Low Temperature Aging ◽  
Novel Design ◽  
Temperature Aging

A novel method based on nano-scale precipitation hardening has been studied to strengthen copper-bearing ferrite antibacterial stainless steel. Bimodal precipitations can be observed after antibacterial annealing and low temperature aging treatment, which are large rod-shaped precipitates and nano-sized spherical precipitates, respectively. Due to two different morphological precipitates, the strength of the material is significantly improved without sacrificing formability, and at the same time, the excellent antibacterial properties remain. Under low temperature aging treatment, there is no obvious evidence to show the segregation at the interface between the rod-shaped copper precipitation and the matrix due to the low segregation coefficient of copper. The nano-sized copper precipitation uniformly nucleated and distributed on the matrix. The optimized heat treatment process is antibacterial annealing at 800 °C for half an hour followed by one-hour-aging treatment at 550 °C.

Sign in / Sign up

Export Citation Format

Share Document